Commit graph

32 commits

Author SHA1 Message Date
Lokesh Vutla
37be54fd13 ARM: BeagleBoard-x15: Enable i2c5 clocks
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-15 10:57:26 -04:00
Lokesh Vutla
eda6fbcc8c ARM: DRA7: Add support for IO delay configuration
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.

It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.

IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-06-12 13:02:05 -04:00
Dileep Katta
f12467d1a5 ARM: DRA7: Set serial number environment variable
This patch populates serial number environment variable from
die_id_0 and die_id_1 register values for DRA7xx boards.

The function is added in omap common code so that this can be re-used.

Serial# environment variable will be useful to show correct
information in "fastboot devices" commands.

Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c

Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-23 13:59:19 -04:00
Kishon Vijay Abraham I
d3cfcb3e2c ARM: DRA7: Enable clocks for USB OTGSS and USB PHY
Enabled clocks for dwc3 controller and USB PHY present in DRA7.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:08 +02:00
Felipe Balbi
113d7e88cb arm: dra7xx: prcm: add missing registers
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:13 -05:00
Lokesh Vutla
02847fcc92 ARM: DRA7xx: ctrl: Fix efuse register addresses
Efuse register addresses are wrongly programmed.
Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
Nishanth Menon
82da4410f8 DRA7: fix ABB efuse offset for OPP_NOM
commit 194dd74ad9
(DRA7: add ABB setup for MPU voltage domain)

Made an offset typo error by using 0x4A003B24 as the efuse offset
for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and
0x4A003B20 is for OPP_NOM. Fix the same.

Reported-by: Praveen Rao <prao@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2014-02-21 13:55:41 -05:00
Nishanth Menon
194dd74ad9 DRA7: add ABB setup for MPU voltage domain
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Roger Quadros
5afded6a4c ARM: DRA7xx: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on DRA7xx.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
8ffcf74bb0 ARM: OMAP5: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on OMAP5.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Wolfgang Denk
16641d52fc Coding Style cleanup: drop some excessive empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Matt Porter
c97a9b3275 omap5: add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:50 +05:30
Lokesh Vutla
e22cc0cf13 ARM: OMAP5: Avoid writing into LDO SRAM bits
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.

Boot tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
f986d97208 ARM: DRA7xx: Enable GMAC clock control
Enabling CPSW module by enabling GMAC clock control

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Lokesh Vutla
65e9d56fb9 ARM: DRA7xx: Lock DPLL_GMAC
Locking DPLL_GMAC

[mugunthanvnm@ti.com:Configure only if CPSW is selected]

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lubomir Popov
ee28edac43 OMAP5: Enable access to auxclk registers
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.

Also remove unrelated TPS62361 defines from clocks.h

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10 08:54:46 -04:00
Sricharan R
92b0482c17 ARM: DRA7xx: EMIF: Change settings required for EVM board
DRA7 EVM board has the below configuration. Adding the
settings for the same here.

   2Gb_1_35V_DDR3L part * 2 on EMIF1
   2Gb_1_35V_DDR3L part * 4 on EMIF2

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lubomir Popov
e0a8c99e61 OMAP5: Fix bug in omap5_es1_prcm struct
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.

Add .prm_rsttime address init to the ES1.0 struct.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
e69c585d76 OMAP5: add ABB setup for MPU voltage domain
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
0b1b60c779 ARM: OMAP5: Fix warm reset with USB cable connected
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-05-10 08:25:55 -04:00
Lokesh Vutla
8b12f1779e arm: dra7xx: Add control module changes
Control module register addresses are changed from OMAP5
to DRA7XX socs.
So adding the necessary changes for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4e4129c31 arm: dra7xx: clock: Add the prcm changes
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX.
So adding the necessary register changes for DRA7XX socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
d4d986ee27 ARM: OMAP5: srcomp: enable slew rate compensation cells after powerup
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
	 The 1 in wkup domain is not enabled because smart i/os
	 of wkup domain work with default compensation code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
SRICHARAN R
afc2f9dcf1 ARM: OMAP5: clock: Add the prcm register changes required for ES2.0
PRCM register addresses are changed from ES1.0 to ES2.0 due to
PER power domain getting moved to CORE power domain.

So adding the nessecary register changes for the same.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
Lokesh Vutla
c43c8339fe ARM: OMAP4+: Make control module register structure generic
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
01b753ff7b ARM: OMAP4+: Change the PRCM structure prototype common for all Socs
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.

Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11 11:06:09 -04:00