This Freescale logo is a 340 x 128 x 4bpp BMP file
that can be displayed by the DIU Framebuffer driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch implements general ULi 526x Ethernet driver.
Until now, it is the only native Ethernet port on
MPC8610HPCD board, but it could be used on other boards
with ULi 526x Ethernet port as well.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and
"miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which
returns non-zero iff the PHY registers are configured for 1000BASE-X. The
"mii info" command is modified to distinguish between 1000BASE-T and -X.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
The scan code of the key 'z' is 0x1d, which should be handled.
The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
controller.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
The configuration file has already enabled USB, but it
missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
on MPC8641HPCN can not work because of the wrong USB
register endian.
And add the USB command to U-Boot commands list.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
usb_cpu_init() configures GPS USB pins, clocks, etc. and
is required for proper operation of kernel USB subsystem.
This setup was previously done in the kernel by the fixup
code which is being removed, thus low level init must be
done by U-boot now.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Since December 2003 the timer_interrupt_cpu() function in
cpu/mpc824x/interrupts.c contains what seems to be a superfluous
parameter. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
To get the IDS8247 board working following are done:
- FCC2 is deactivated
- FCC1 is activated
- I2C is activated
- CFI driver is activated
- Adapted for use with LIBFDT
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang is right: It's not a good idea to set up default initial
ethernet addresses for a board, even though they belong to the local
range.
This will change the failure mode from "IT manager screams at you for
using duplicate ethernet addresses" to a nice error message explaining
that the ethernet address hasn't been set properly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This is a multi-part message in MIME format.
commit e6e505eae94ed721e123e177489291fc4544b7b8
Author: Justin Flammia <jflammia@savantav.com>
Date: Mon Oct 29 17:19:03 2007 -0400
Found a bug in the way the DHCP Request packet is built, where the IP address
that is offered by the server is bound to prematurely. This patch is a fix of
that bug where the IP address offered by the DHCP server is not used until
after the DHCP ACK from the server is received.
Signed-off-by: Justin Flammia <jflammia@savantav.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Since the cache handling functions were moved from start.S into cache.S
the acadia NAND booting Makfile needs to be adapted accordingly.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Now with caches enabled (i- and d-cache) on 44x, we need a chance to
disable the cache for the CPU POST tests, since these tests consist
of self modifying code. This is done via the new change_tlb() function.
Signed-off-by: Stefan Roese <sr@denx.de>
I lately noticed, that newer 4xx board with GBit support sometimes don't
finish link autonegotiation in 4 seconds. Changing this timeout to 5
seconds seems fine here.
Signed-off-by: Stefan Roese <sr@denx.de>
