Folder names corresponds to DT name. These boards have been renamed from
zc1275 to zcu1275 by commit shown below and this should be the part of that
commit.
Fixes: 420d446781 ("arm64: zynqmp: Rename zc1275 to zcu1275")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enable i2c controller clock from driver probe function
by calling clk_enable().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add clock enable functionality in versal clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock enable functionality in zynqmp clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to clear reset reason register because it is protected by
PMUFW already which is reported when verbose log is enabled as:
pm_core.c@733 APU> No write permission to 0xFF5E0220
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to pointer arithmetic, "sizeof(u32) * ARCH_DMA_MINALIGN" is
subtracted. It seems that the original intention was to just subtract
ARCH_DMA_MINALIGN. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both Zynq and ZynqMP can show silicon versions in SPL boot flow. It is
useful to be aware.
The patch is also fixing possition of these bits on ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix bug introduced by commit listed below. It is for cases where Versal or
ZynqMP don't have DDR mapped. Later SPL was also excluded by
commit a672b9871b ("xilinx: common: Do not touch
CONFIG_XILINX_OF_BOARD_DTB_ADDR in SPL").
Fixes: 506009fc10 ("xilinx: common: Change macro handling in board_fdt_blob_setup()")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dm_spi_ops.xfer() API does not support dual and quad SPI modes. It
also doesn't allow the zynqmp_gqspi driver to calculate the correct
number of dummy cycles for some NOR ops (as doing so also requires the
buswidth).
Port the zynqmp_gqspi driver to spi_controller_mem_ops, which gives us
the buswidth values to correctly support all SNOR_PROTO_X_X_X commands
and to properly calculate dummy cycles.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit dd5c954e91 ("travis/gitlab/azure: Use -W to avoid warnings check")
added -W to avoid warnings check, but it mistakenly dropped -E for
the world build script in the azure pipelines.
This caused builds on the azure pipelines fail to report warnings. Let's
add it back.
Fixes: dd5c954e91 ("travis/gitlab/azure: Use -W to avoid warnings check")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The implementation of pytest_runtest_protocol() must call
pytest_runtest_logstart() and pytest_runtest_logfinish(). This appears to
be necessary even in pytest 5.2.1 judging by the default version of
pytest_runtest_protocol(), but evidently some form of code reorganization
in pytest only made this have a practical effect in the newer version. I'd
previously been under the impression that 100% of the required work of
pytest_runtest_protocol() was handled by the fact it called
runtestprotocol() as its implementation. However, it appears that custom
implementations do need to do a little more than this.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add myself as co maintainer to network subsystem
Acked-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixes issues when switching from GPT to MBR partition tables.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Config allows to disable printing contents of fitImage to optimize boottime.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The load command should not silently return to the console prompt if an
invalid block device is specified and no file is loaded.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
No version information is used in armv8/fwcall.c therefore do not include
version.h header file. This change prevents recompiling fwcall.o when
SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
With the recent addition of ACPI generation, the image size has got beyond
its current limit.
Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enhance the debugging to show the next stage being booted as well as a
dump of the start of the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should be done even if not using TPL, since BSS may be in use or
boards that only use SPL. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if the command line is very long it is truncated by the
printf() statement, which works within a limited buffer. Use puts()
instead. Also show better debugging with the command-line setup
fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present it is possible to dump an image within the zimage command, but
it is also useful to be able to dump it from elsewhere, for example in a
loader that has special handling for the different zimage stages.
Export this feature as a new function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Global Non-Volatile Storage struct has some fields with particular
meanings. Rename these to make things easier to follow. Also add a few
more boot flags.
GNVS should not be confused with GNVQ (Going Nowhere Very Quickly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present BSS is always placed in SDRAM. If a separate BSS is not in use
this means that BSS doesn't work as expected. Make the setting conditional
on the SEPARATE_BSS option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The part of U-Boot that actually ends up in u-boot-nodtb.bin is not built
with any particular alignment. It ends at the start of the BSS section.
The BSS section selects its own alignment, which may larger.
This means that there can be a gap of a few bytes between the image
ending and BSS starting.
Since u-boot.bin is build by joining u-boot-nodtb.bin and u-boot.dtb (with
perhaps some padding for BSS), the expected result is not obtained. U-Boot
uses the end of BSS to find the devicetree, so this means that it cannot
be found.
Add 32-byte alignment of BSS so that the image size is correct and
appending the devicetree will place it at the end of BSS.
Example SPL output without this patch:
Sections:
Idx Name Size VMA LMA File off Algn
0 .text 000142a1 fef40000 fef40000 00001000 2**4
CONTENTS, ALLOC, LOAD, RELOC, READONLY, CODE
1 .u_boot_list 000014a4 fef542a8 fef542a8 000152a8 2**3
CONTENTS, ALLOC, LOAD, RELOC, DATA
2 .rodata 0000599c fef55760 fef55760 00016760 2**5
CONTENTS, ALLOC, LOAD, RELOC, READONLY, DATA
3 .data 00000970 fef5b100 fef5b100 0001c100 2**5
CONTENTS, ALLOC, LOAD, RELOC, DATA
4 .binman_sym_table 00000020 fef5ba70 fef5ba70 0001ca70 2**2
CONTENTS, ALLOC, LOAD, DATA
5 .bss 00000060 fef5baa0 fef5baa0 00000000 2**5
ALLOC
You can see that .bss is aligned to 2**5 (32 bytes). This is because of
the mallinfo struct in dlmalloc.c:
17 .bss.current_mallinfo 00000028 00000000 00000000 000004c0 2**5
ALLOC
In this case the size of u-boot-spl-nodtb.bin is 0x1ba90. This matches up
with the _image_binary_end symbol:
fef5ba90 g .binman_sym_table 00000000 _image_binary_end
But BSS starts 16 bytes later, at 0xfef5baa0, due to the 32-byte
alignment. So we must align _image_binary_end to a 32-byte boundary. This
forces the binary size to be 0x1baa0, i.e. ending at the start of bss, as
expected.
Note that gcc reports __BIGGEST_ALIGNMENT__ of 16 on this build, even
though it generates an object file with a member that requests 32-byte
alignment.
The current_mallinfo struct is 40 bytes in size. Increasing the struct to
68 bytes (i.e. just above a 64-byte boundary) does not cause the alignment
to go above 32 bytes. So it seems that 32 bytes is the maximum alignment
at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add more details in the commit message to help people understand]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move to log_debug() and make use of the new SPL function to find the
text base.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to know the TEXT_BASE value for the image being loaded in
TPL/SPL. Add a new spl_get_image_text_base() function to handle this.
Make use of this in the x86 SPL handler, instead of having the logic
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use a driver name in line with the compatible string so that of-platdata
can use this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some comments were provided after this patch was applied. Address them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a node for this so we can indicate that it is does not require any
ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present long delays such as msleep(2000) can cause an overflow in this
function. There is no need for this, since it already uses a 64-bit int.
Add a cast to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Trying to compile qemu-x86_64_defconfig with CONFIG_CMD_ACPI=y and
CONFIG_ACPIGEN=n fails with
ld.bfd: cmd/built-in.o: in function `do_acpi_items':
cmd/acpi.c:162: undefined reference to `acpi_dump_items'
Add the missing configuration dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useless and misleading to print the ret variable that is not set
by the dev_read_addr routine. Also, move the '\n' character after the
round bracket that contains the error code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With the fixes to the sun8i-emac driver, we can now enable Ethernet
support on the OrangePi Zero2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAV6K8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYERgf/QbwOL87yPbf9SyXBQ0EMTmn1ve9HCiv9
yeXrijvA0/wtTVoM44d/z7THb+7Zqw6LbsVOXUSicdGqaogy10xIuz5we0CoGJm6
iwYWV6kaAqjCxDTlSToGnR/TCjiOVgXC6u5QPCZC0LGbAmDbAl4jyCuQxxq2eXYD
hrLSzZPHDe0s2BeWZKRQJ26qyPfWIribXNJXG78/FsvDrdWPPc5K+/ZEb2IWawWR
nEZ8GTEYZpik/niEJ3gFozwCwpJQi3PyukjZvzTGn6tBqg12YXE4dbSzcj48Uj4o
prwUFAGKRR97zFB6c4+NUvd3VBUgPtPdZrtzZ1nNCppiMq1E4BKiDg==
=kijh
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-30jan21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
tpm fixes for coral
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
