This patch fixes a problem with the RGMII setup of the 460GT. The 460GT
has 2 RGMII instances and we need to configure the 2nd RGMII instance
for the EMAC2+3 channels.
Signed-off-by: Stefan Roese <sr@denx.de>
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
correctly configures the SATA/PCIe PHY for SATA usage when this jumper
is installed.
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the ptm1la, ptm1ms, ptm2la and ptm2ms
environment variables.
Cleanup pci_target_init.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This punts the old spi flash driver for a new/generalized one until the
common one can be integrated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds a driver for the following smsc network controllers:
LAN9115
LAN9116
LAN9117
LAN9215
LAN9216
LAN9217
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds the core support for Freescale mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
- Adapt register naming to recent TI spec (sprue26, March 2007)
- Fix reset_timer() handling
- As reported by Pieter [1] the overflow fix introduced a
delay of factor 16 (e.g 2 seconds became 32). While the
overflow fix is basically okay, it missed to divide udelay by
16, too. Fix this.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/38179
- Remove software division of timer count value (DIV(x)
macro) and do it in hardware (TIM_CLK_DIV).
Many thanks to Troy Kisky <troy.kisky@boundarydevices.com>
and Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl> for
the hints & testing!
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl>
SPARC has implemented __raw_readq, it reads 64-bit from any 32-bit address.
SPARC CPUs implement flash_read64 which calls __raw_readq.
For current SPARC architectures (LEON2 and LEON3) each read from the
FLASH must lead to a cache miss. This is because FLASH can not be set
non-cacheable since program code resides there, and alternatively disabling
cache is poor from performance view, or doing a cache flush between each
read is even poorer.
Forcing a cache miss on a SPARC is done by a special instruction "lda" -
load alternative space, the alternative space number (ASI) is processor
implementation spcific and can be found by including <asm/processor.h>.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Remove a few absolute references to CFG_MONITOR_BASE for ppc/mpc83xx
and use GOT relative reference.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 55774b512f broke the onboard USB
controller on the PCI bus in Linux on the MPC8323ERDB.
This fixes it by defining CONFIG_PCI_SKIP_HOST_BRIDGE in the board's
config file.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
delete ddr_clk and use mem_clk instead. Rename other ddr_*_clk to
mem_*_clk for consistency's sake.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enable the first two SATA interfaces on MPC837xEMDS board,
The two SATA ports are on LYNX1. (SATA0/1 on J4/5)
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
displays the current configuration upon bootup and changes the PCIe
init loop, to only initialize the availabel PCIe slots.
Signed-off-by: Stefan Roese <sr@denx.de>
Add entry for 512Kx16 AMD flash to jedec_table.
Read out 16bit device id if chipwidth is 16bit.
Fixed coding style after Stefans feedback
Signed-off-by: Tor Krill <tor@excito.com>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
