Synchronize R-Car R8A77970 V3M DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7792 V2H DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It may be necessary to set breakpoints etc. on a specific fault handler in SPL.
Add a Kconfig option to separate the different handlers into their own individual infinite loops.
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Use device specific naming for functions so as to not overlap
with common function names.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix compilation issue with overlapping lwip and march defines.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
all network drivers return 0 on the successful
transmission.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a new eDPU revision that uses Marvell 88E6361 switch onboard.
We can rely on detecting the switch to enable and fixup the Linux DTS
so a single DTS can be used.
There is currently no support for the 88E6361 switch and thus no working
networking in U-Boot, so we disable both ports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
The ATF implementation for AC5/AC5X ends up with bl31 living in some
internal SRAM. This is in the middle of the large MMIO region that we
were using. Adjust this to be finer grained blocks based on the address
map from the AC5X Family Control and Management Subsystem Functional
Datasheet.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Select CONFIG_SUPPORT_ACPI to allow usage of ACPI tables with RISC-V.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add fields for the location of ACPI tables to the global data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add fields for the location of ACPI tables to the global data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fields X_FIRMWAE_CTRL and X_DSDT must be 64bit wide. Convert pointers to
to uintptr_t to fill these.
If field X_FIRMWARE_CTRL is filled, field FIRMWARE must be ignored. If
field X_DSDT is filled, field DSDT must be ignored. We should not fill
unused fields.
See the field definitions in chapter "5.2.9 Fixed ACPI Description Table
(FADT)" of the ACPI Specification 6.5.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox uses an API to map between addresses and pointers. This allows
it to have (emulated) memory at zero and avoid arch-specific addressing
details. It also allows memory-mapped peripherals to work.
As an example, on many machines sandbox maps address 100 to pointer
value 10000000.
However this is not correct for ACPI, if sandbox starts another program
(e.g EFI app) and passes it the tables. That app has no knowledge of
sandbox's address mapping. So to make this work we want to store
10000000 as the value in the table.
Add two new 'nomap' functions which clearly make this exeption to how
sandbox works.
This should allow EFI apps to access ACPI tables with sandbox, e.g. for
testing purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754 ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Manorit Chawdhry <m-chawdhry@ti.com> says:
K3 devices have firewalls that are used to prevent illegal accesses to
memory regions that are deemed secure. The series prevents the illegal
accesses to ATF and OP-TEE regions that are present in different K3
devices.
AM62X, AM62AX and AM64X are currently in hold due to some firewall
configurations that our System Controller (TIFS) needs to handle.
The devices that are not configured with the firewalling nodes will not
be affected and can continue to work fine until the firewall nodes are
added so will be a non-blocking merge.
Test Logs: https://gist.github.com/manorit2001/4cead2fb3a19eb5d19005b3f54682627
CICD Run: https://github.com/u-boot/u-boot/pull/442
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For readability during configuring firewalls, adding k3-security.h file
and including it in k3-binman.dtsi to be accessible across K3 SoCs
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Principle is exactly the same as on T124, testing of register
which behaves differently in secure and non-secure states.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu secure proxy node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The dummy_clock node is used to help the drivers probe the IO needed to
setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the
mcu domain. So move it from cbass_mcu to the root node to avoid any
confusion.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
These aliases are not needed in U-Boot. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we have duplicate
properties in the root node. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate vtt_pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mdio node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The pinmux for usb0 is missing from the Linux board dtb file. Remove it
until we can introduce it in Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate ospi0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have
a duplicate sdhci0 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate main_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate mcu_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
[0] https://lore.kernel.org/r/20231213135138.929517-2-vigneshr@ti.com
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_udmap node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
