This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
lowlevel_init.S: Assembler messages:
lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local.
Looking at codes, the `memtest' and `clearmem' are intentional mixed
use of `global symbols' and `label' for debugging purpose. To make it
build, just disable global-symbols-use for now. As a result `memtest'
still remains as unused, but leave it be...
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
gth2.c: In function 'misc_init_r':
gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Ugh. I *hate* to back this change out, but these compiler flags don't
work for relocation on all versions of GCC. I've not been able to
reproduce the environment in my setup (and hence, not been able to
find a combination that *does* work), so I've got no choice but to go
back to the old gcc flags and linker script.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch has been sent on:
- 29 Sep 2007
Although mips_io_port_base is currently a part of IDE command, it is quite
fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
it to MIPS general part, and introduce `set_io_port_base()' from Linux.
This patch is triggered by multiple definition of `mips_io_port_base' build
error on gth2 (and tb0229 also needs this fix.)
board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
/home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
make: *** [u-boot] Error 1
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch adds changes needed for Makalu rev 1.1:
- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup
Signed-off-by: Stefan Roese <sr@denx.de>
usb_cpu_init() configures GPS USB pins, clocks, etc. and
is required for proper operation of kernel USB subsystem.
This setup was previously done in the kernel by the fixup
code which is being removed, thus low level init must be
done by U-boot now.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
To get the IDS8247 board working following are done:
- FCC2 is deactivated
- FCC1 is activated
- I2C is activated
- CFI driver is activated
- Adapted for use with LIBFDT
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch also adds a note to the fixed DDR setup for Bamboo NAND booting:
Note:
As found out by Eugene O'Brien <eugene.obrien@advantechamt.com>, the fixed
DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM
modules are still plugged in. So it is recommended to remove the DIMM
modules while using the NAND booting code with the fixed SDRAM setup!
Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Change all linker scripts to reference the changed driver name 4xx_uart.o.
Note: In most cased all these explicit referencing of these object files
in the linker scripts is not neccessary. Only for manually embedded
environment into the U-Boot image, which is not done is most cases.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
The size was initilized wrong. Instead of 256MB, the DDR2 controller
was setup to 512MB. Now the correct values is used.
This patch also does a little cleanup and adds a comment here.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.
This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:
pcie_mode=RP:EP:EP
This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.
Per default Yucca will be configured as:
pcie_mode=RP:EP:EP
Per default Katmai will be configured as:
pcie_mode=RP:RP:REP
Per default Kilauea will be configured as:
pcie_mode=RP:RP
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.
This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.
Signed-off-by: Stefan Roese <sr@denx.de>
