Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid
getting a warning that the mx6sabresd_spl is not maintained.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move MX5 specific set_chipselect_size function into generic i.MX part,
such that MX6 based boards are able to use this function as well.
While doing this the iomuxc gpr member needed to be consolidated between
MX5 and MX6.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Many boards use a minimal .cfg file in the SPL case.
Introduce spl_sd.cfg so that we can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit 3ff46cc4 fixed exception vectors setting in
the general ARM case, by either copying the exception
and indirect vector tables to normal (0x00000000) or
high (0xFFFF0000) vectors address, or setting VBAR to
U-Boot's base if applicable.
i.MX27 SoC is ARM926E-JS, thus has only normal and
high options, but does not provide RAM at 0xFFFF0000
and has only ROM at 0x00000000; it is therefore not
possible to move or change its exception vectors.
Besides, i.MX27 ROM code does provide an indirect
vectors table but at a non-standard address and with
the reset and reserved vectors missing.
Turn the current vector relocation code into a weak
routine called after relocate_code from crt0, and add
strong version for i.MX27.
Series-Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Tested-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Philippe Reynes <tremyfr@yahoo.fr>
Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to
1. So modify the default mmcdev in environment variables to dev 1.
Signed-off-by: Ye.Li <B37916@freescale.com>
The PFUZ probe failed with the following msg:
" wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=0
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=1
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=2
i2c_init_transfer: give up i2c_regs=021a0000
Can't find PMIC:PFUZE100 "
board_early_init_f is too early to call i2c related setting, because
init_func_i2c is called after board_early_init_f being invoked. Thus
move setup_i2c into board_init.
Also PFUZ is connected to I2C bus 0, so change "1" -> "0".
Using this patch PFUZ can be correctly probed:
"PMIC: PFUZE100 ID=0x11"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mkimage -T mxs now support new flag in config file:
DISPLAYPROGRESS - makes boot process print HTLLC characters for each BootROM
instruction.
Signed-off-by: Alexey Ignatov <lexszero@gmail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add support for using spl code on at91sam9260 and at91sam9g45
based boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[adopt Bo's change in spl.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
- compile mpddrc ram init code also for AT91SAM9M10G45
based boards.
- in CONFIG_SAMA5D3 case, look for the ATMEL_MPDDRC_CR_DECOD_INTERLEAVED
in the cr configuration
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
use the configure value for computing the ba_off value
not the value from the cr register. This leaded in a
wrong ram configuration on the upcoming corvus spl board
support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The clock source for master clock can be slow clock, main clock,
plla clock or upll clock. So, make the clock source selection
field in mckr can be configured.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
We need to make sure the main clock ready field in MCFR is set
after switch to main crystal oscillator.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Common part of config for lager, koelsch, alt and gose board will be able to
replace rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Gose board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koesch board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
