This patch changes the initialization of the AHCI controller to not
enable the default interrupts (DEF_PORT_IRQ). As interrupts are
not used in U-Boot in general, this should not break the common AHCI
driver operation.
This change is needed to support the Marvell Armada 38x AHCI
controller. With interrupts enabled, this results in timeouts in
ahci_device_data_io(). Not enabling these interrupts fixes this
problem and the common AHCI driver works fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the
following problem occured. The SPL runs in internal SRAM which is
the L2 cache locked to memory. When the MMC buffers now are located
on the stack (or bss), the SDIO controller (SDHCI) can't write into
this L2 cache memory.
This patch introduces a method to use a fixed buffer that will be
used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER.
This way, the board can use this buffer address located in SDRAM
for all transfers. This solves this SPL problem on the A38x and
should only be used in the SPL U-Boot version.
Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The loop counter based timeout detection does not work on the Armada
38x based board (DB-88F6820-GP). At least with dcache enabled a
timeout is detected. Without dcache enabled, the timeout does not
occur. Increasing the loop counter solves this issue. But a better
solution is to use a timer based timeout detection instead. This
patch now implements this timer based detection.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When driver model is not used the current code does not correctly select
the pinmux for the I2C bus. This bug was introduced by this commit:
8dfcbaa dm: i2c: s3c24x0: adjust to dm-i2c api
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When compling under 64bit platforms, there are lots of warnings,
like:
drivers/block/ahci.c:114:18: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
u8 *port_mmio = (u8 *)probe_ent->port[port].port_mmio;
^
drivers/block/ahci.c: In function ?.hci_host_init?.
drivers/block/ahci.c:218:49: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
probe_ent->port[i].port_mmio = ahci_port_base((u32) mmio, i);
......
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
commit f566c99 "net: Update hardware MAC address if it changes in env"
removes writing MAC address to designware controller after soft reset.
This makes designware ethernet port fail to work. Actually the MAC
address should always be programmed after soft reset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Added UART DCC support for armv8
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The LPC32XX GPIO driver platdata currently contains GPIO state information,
which should go into priv_data. Thus rename lpc32xx_gpio_platdata to
lpc32xx_gpio_priv and convert to use dev_get_priv() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
This patch makes the code compatible with FIFO depths other than 4
bytes. It also simplify read/write FIFO loops.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
There is no need to re-configure sram partition for every read/write for
better full use of sram for read or write. This patch divides the half
sram for read & half for write once at initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Added TEGRA20_SLINK entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added TEGRA20_SFLASH entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added TEGRA114_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added ICH_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Added FSL_QSPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
DM supported spi drivers are enbled only when DM_SPI enabled,
so added DM_SPI if condition in Kconfig to show thoese only
when it enabled.
Also re-order the config items as incresing alphabetic order.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch includes asm/io.h for readl and writel calls.
build errors:
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_probe':
drivers/spi/xilinx_spi.c:119:2: warning: implicit declaration of function 'writel' [-Wimplicit-function-declaration]
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_xfer':
drivers/spi/xilinx_spi.c:193:2: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>
This converts the xilinx spi driver to use the driver model.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
This converts the zynq spi driver to use the driver model.
Minimal functional changes like using meaningful name on
structure members wrt mainlined dm spi drivers.
- input_hz -> frequency
- req_hz -> freq
- base -> regs
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Arrange driver code in more readable format[1] for easy accessing
and readable.
[1] http://patchwork.ozlabs.org/patch/265683/
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Move the header code into driver for more readable and
easy to access it.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Move the header code into driver for more readable and
easy to access it.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Zap oc_tiny_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Zap ftssp010_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Axel Lin <axel.lin@ingics.com>
Zap andes_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Macpaul Lin <macpaul@andestech.com>
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Patch 33fe2fb8df titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.
Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.
But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We want to see if the requested start or total block count are
unaligned. We discard the whole numbers and only care about the
remainder. Update the code to use div_u64_rem here and add a comment.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The AHCI driver currently waits 5s before timing out when sending a
data command to a drive. Some drives take upwards of 8s to respond to
the initial data command while they're spinning up. Increase the
data io timeout to 10s so that those drives can be found on initial
scsi scan.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow SPL to be built with this option so that we can support device tree
control. Disable the simple bus for now in SPL. It may be needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature should be deprecated for new boards, and significantly adds
to SPL code size. Drop it. Instead, we can use stdout-path in the /chosen
node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is used by some boards, so support it with driver model. This
is really ugly - we should rewrite this driver once all users are moved to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
We try to avoid typedefs and these ones are easy enough to remove. Before
changing this header in the next patch, remove the typedefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the legacy i2c_reg_read/write() functions to the compatibility layer
so that they can be used when CONFIG_DM_I2C_COMPAT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Use the oscillator as the source clock when we cannot achieve a low-enough
speed with the peripheral clock. This happens when we request 3MHz on a SPI
clock, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present the driver does not properly honour the requested SPI CS
deactivation delay since the SPI bus is changed in the claim_bus() method.
Everything the claim_bus() method does can be done when the device is probed
(setting the speed and mode) and at the start of a new transfer (where the
fifo_status is already cleared). So drop this method.
Also, until the delay is complete, we should not touch the bus, so make sure
that spi_cs_activate() is called before other things are done in the xfer()
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This change decreases the interval of calls to:
- display busy indicator
- check ctrlc()
- check cable connection
By this change, breaking the UMS command is more easy on Odroid XU3.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.
This code is used thereafter in the board_usb_init() call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Add a weak function board_ehci_hcd_init which can be used by the board
file for board specific initialisation.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Like SPI and I2C few GPIO controllers also have
multiple chip instances. This patch adds the
flag 'DM_UC_FLAG_SEQ_ALIAS' in gpio_uclass driver
to control device sequence numbering. By defalut
the dev->r_seq for gpio_uclass will alwalys
returns -1, which leads the gpio driver probe
failure when using the driver with device trees.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Return if USB_MAX_CONTROLLER_COUNT hence the index of the controller
to be initialised is incorrect
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Add "allwinner,sun8i-a33-pinctrl", this is used by the latest upstream
linux sunxi dts files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Commit 9cc36a2 'dm: core: Add a flag to control sequence numbering' changed
the default uclass behaviour to not support bus numbering. This is incorrect
for PCI and that commit should have enabled the flag for PCI.
Enable it so that PCI buses can be found and the 'pci' command works again.
Also add a test for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
The legacy IDE device has a BAR4 (Bus Master Interface BAR) which
needs to be configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Remove the '#undef DEBUG' in pci_auto.c so that we can enable debug
message output via '-DDEBUG'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no reason to prevent CONFIG_VIDEO_VESA driver working on
non-x86 boards, so remove such limitation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
pci_hose_phys_to_bus() is needed by several drivers. Move it to
pci_common.c to avoid a broken build when CONFIG_DM_PCI is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This has been tested to the extent that I can enumerate
a asix usb networking adapter and boot a kernel over usb
on the 96boards hikey u-boot port I'm currently doing.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Update the ci_udc driver to support bulk transfer
and also added capability of having multiple dtds
if requested data is more than 16K.
These changes are tested for both the DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Since i've been married, i also have a new surname.
Mr. Petermaier moved to Mr. Schmelzer.
In this patch i update all files in which my (old) name is present.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Function 'sprintf' does not check buffer boundaries but outputs
to the buffer of fixed size which could potentially cause buffer
overflow. Use a safer function to replace it.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
If we are displaying detected PCI devices (CONFIG_PCI_SCAN_SHOW) display
a 'PCI:' header prior to scan.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Due to a misunderstanding, in 698a12b we reverted changes that we in
fact wanted to keep. So lets fix that mistake and bring the code back
to how it should have been.
This reverts commit 698a12bef9.
Signed-off-by: Tom Rini <trini@konsulko.com>
The CPU temperature grade from OTP is now used to define the critical
threshold at which point we busyloop until we are below, however this
threshold is still too low.
Instead of 20C below the max CPU temperature, change it to 5C defined now
by TEMPERATURE_HOT_DETLA for clarity. Rename 'passive' to 'critical'
as that better defines our use case here. Additionally change the output
of the busyloop message to show the max CPU temperature as well as current.
Before:
CPU Temperature is 101 C, too hot to boot, waiting...
CPU Temperature is 101 C, too hot to boot, waiting...
After:
CPU Temperature (101C) too close to max (105C) waiting...
CPU Temperature (101C) too close to max (105C) waiting...
Cc: Stefan Roese <sr@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Ye Li <b37916@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Peng Fan <b51431@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The break after return is unreachable code, remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
pwm_id_to_reg() can return NULL, so add NULL testing to prevent NULL pointer
dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).
Signed-off-by: Stefan Agner <stefan@agner.ch>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
the special handling of OOB (spareonly).
Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.
However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.
Signed-off-by: Stefan Agner <stefan@agner.ch>
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Freeing allocated memory to priv before returning
from the function
Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.
This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).
I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Remove the calls to net_random_ethaddr() that some boards and some
drivers are calling. This is now implemented inside of net/eth.c
Enable the feature for all boards that previously enabled it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-By: Michael Walle <michael@walle.cc> (for the lsxl board part)
Series-changes: 2
-Fixed bfin build errors
We really don't want boards defining fixed MAC addresses in their config
so we just remove the option to set it in a fixed way. If you must have
a MAC address that was not provisioned, then use the random MAC address
functionality.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers passed to phy_register
function.
This patch was tested on Microblaze architecture.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RTL8211F needs to enalbe TXDLY for RGMII during
phy initialization, so move it to rtl8211f_config
for early initialization.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When the ethaddr changes in the env, the hardware should also be updated
so that MAC filtering will work properly without resetting U-Boot.
Also remove the manual calls to set the hwaddr that was included in a
few drivers as a result of the framework not doing it.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
RTL8211F has different registers from RTL8211E.
This patch adds support for RTL8211F PHY which
can be found on Freescale's T1023 RDB board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We've never tested the lvds panel support on sun6i+ SoCs until now, and
unsurprisingly the lvds code needed some fixes to work on my ga10h A33
tablet with lvds panel. This makes the panel on that tablet actually work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Replace the hard-coded values for min/max/passive with values derived from
the CPU temperature grade.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Prevent overflow by casting duty_ns to ull first. This bug came up when trying to create a 200 Hz PWM
Signed-off-by: Brecht Neyrinck <bnrn@psicontrol.com>
Acked-by: Heiko Schocher<hs@denx.de>
This commit adds emulation of sandbox PMIC device, which includes:
- PMIC I2C emulation driver
- PMIC I/O driver (UCLASS_PMIC)
- PMIC regulator driver (UCLASS_REGULATOR)
The sandbox PMIC has 12 significant registers and 4 as padding to 16 bytes,
which allows using 'i2c md' command with the default count (16).
The sandbox PMIC provides regulators:
- 2x BUCK
- 2x LDO
Each, with adjustable output:
- Enable state
- Voltage
- Current limit (LDO1/BUCK1 only)
- Operation mode (different for BUCK and LDO)
Each attribute has it's own register, beside the enable state, which depends
on operation mode.
The header file: sandbox_pmic.h includes PMIC's default register values,
which are set on i2c pmic emul driver's probe() method.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
The function get_emul() in sandbox i2c bus driver, always returns
first child as i2c emul device. This may only work for i2c devices
with a single child, which is an only i2c emul device.
In case when i2c device has more than one child (e.g. PMIC), and
one is i2c emul, then the function should search it by check uclass
id for each child. This patch add this change to the get_emul().
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This cleanup includes:
- remove of the preprocessor macros which pointed to long name functions
- update of the names of some regulator uclass driver functions
- cleanup of the function regulator_autoset()
- reword of some comments of regulator uclass header file
- regulator_get_by_platname: check error for uclass_find_* function calls
- add function: regulator_name_is_unique
- regulator post_bind(): check regulator name uniqueness
- fix mistakes in: regulator/Kconfig
- regulator.h: update comments
- odroid u3: cleanup the regulator calls
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
The cleanup includes:
- pmic.h - fix mistakes in a few comments
- pmic operations: value 'reg_count' - redefine as function call
- fix function name: pmic_bind_childs() -> pmic_bind_children()
- pmic_bind_children: change the 'while' loop with the 'for'
- add implementation of pmic_reg_count() method
- pmic_bind_children() - update function call name
- Kconfig: add new line at the end of file
- Update MAX77686 driver code
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This driver implements regulator operations for fixed Voltage/Current
value regulators. beside the standard regulator constraints, which are
put into the uclass platform data, a typical fixed regulator node provides
few additional properties like:
- gpio
- gpio-open-drain
- enable-active-high
- startup-delay-us
The only 'gpio' is used by this driver and is kept in structure of type
'fixed_regulator_platdata', as a device platform data (dev->platdata).
The driver implements:
- get_value
- get_current
- get_enable
- set_enable
The regulator calls and commands can be used for fixed-regulator devices,
and the proper error will be returned for prohibited.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds support to MAX77686 regulator driver,
based on a driver model regulator's API. It implements
almost all regulator operations, beside those for setting
and geting the Current value.
For proper bind and operation it requires the MAX77686 PMIC driver.
New file: drivers/power/regulator/max77686.c
New config: CONFIG_DM_REGULATOR_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is the implementation of driver model PMIC driver.
The max77686 PMIC driver implements read/write operations and driver
bind method - to bind its childs.
This driver will try to bind the regulator devices by using it's child
info array with regulator prefixes and driver names. This should succeed
when compatible regulator driver is compiled. If no regulator driver found,
then the pmic can still provide read/write operations, and can be used with
PMIC function calls.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the implementation of dm regulator API.
Device tree support allows for auto binding. And by the basic
uclass operations, it allows to driving the devices in a common
way. For detailed informations, please look into the header file.
Core files:
- drivers/power/regulator-uclass.c - provides regulator common functions api
- include/power/regulator.h - define all structures required by the regulator
Changes:
- new uclass-id: UCLASS_REGULATOR
- new config: CONFIG_DM_REGULATOR
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the PMIC uclass implementation.
It allows providing the basic I/O interface for PMIC devices.
For the multi-function PMIC devices, this can be used as I/O
parent device, for each IC's interface. Then, each PMIC particular
function can be provided by the child device's operations, and the
child devices will use its parent for read/write by the common API.
Core files:
- 'include/power/pmic.h'
- 'drivers/power/pmic/pmic-uclass.c'
The old pmic framework is still kept and is independent.
For more detailed informations, please look into the header file.
Changes:
- new uclass-id: UCLASS_PMIC
- new config: CONFIG_DM_PMIC
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
1. Introduce a new structure `struct mxc_i2c_bus`, this structure will
used for non-DM and DM.
2. Remove `struct mxc_i2c_regs` structure, but use register offset to access
registers based on `base` entry of `struct mxc_i2c_bus`.
3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform
flags. A new flag is introduced, I2C_QUIRK_FLAG.
4. Most functions use `struct mxc_i2c_bus` as one of the parameters.
Make most functions common to DM and non-DM, try to avoid duplicated code.
5. Support DM, but pinctrl is not included. Pinmux setting is still set
by setup_i2c, but we do not need bus_i2c_init for DM.
6. struct i2c_parms and struct sram_data are removed.
7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist
paramter of bus_i2c_init is modified to i2c index. Add new prototype
i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for
DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus.
Board file take the responsibility to implement this function, like this:
"
int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
{
if (i2c_bus->index == 0)
force_bus_idle(i2c_pads_info0);
else if (i2c_bus->index == 1)
force_bus_idle(i2c_pads_info1);
else
xxxxxx
}
"
8. Introduce a weak function, enable_i2c_clk
9. Tested on an i.MX7 platform. Log info:
=> dm tree
Class Probed Name
----------------------------------------
root [ + ] root_driver
simple_bus [ ] |-- soc
simple_bus [ ] | |-- aips-bus@30000000
simple_bus [ ] | | |-- anatop@30360000
simple_bus [ ] | | `-- snvs@30370000
simple_bus [ ] | |-- aips-bus@30400000
simple_bus [ ] | `-- aips-bus@30800000
i2c [ ] | |-- i2c@30a20000
i2c [ ] | `-- i2c@30a40000
simple_bus [ ] `-- regulators
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 08 50
=> i2c md 8 31
0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for interrupt queues to the ohci hcd code, bringing it inline
with the ehci and musb-new(host) code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add an ohci_alloc_urb() function, this is a preparation patch for adding
interrupt queue support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When submitting interrupt packets to an endpoint we only link in the ed
once to avoid some races surrounding unlinking of periodic endpoints,
but we share one ohci_device struct / one set of ed-s for all devices,
which means that if we have an interrupt endpoint at endpoint 1 with one
device, and a non interrupt endpoint 1 with another device we end up
with the same ed linked into both the periodic and async lists, which is
not good (tm).
This commit switches over to using separate ohci_device structs, and thus
separate ed-s for devices with interrupt endpoints, fixing this.
This fixes e.g. matching a usb storage device and keyboard on the same
usb-1 hub not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This printf() should have a newline at the end. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We can currently set this but there is no API function to get it. Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Heiko Schocher<hs@denx.de>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
For some reason the ohci code is full with:
#ifdef DEBUG
pkt_print(...)
#else
mdelay(1);
#endif
AFAICT there is no reason for the mdelay(1) calls. This commit disables them
when building the ohci code for new driver-model using boards. It leaves
the mdelay(1) calls in place when building for older boards, so as to avoid
causing any regressions there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb spec says that we must wait a minimum amount of time after port
power on (exact time is in the hub descriptor), this is something which
we must not only do for root ports but also for external hub ports, which
is why the common usb_hub code already waits a full second after powering
up ports. Having a separate wait for just the root hub in the ohci-hcd
code only leads to doing the waiting twice for the root ports, so drop the
wait from the ohci-hcd code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The u-boot usb code uses polling for all endpoints, including interrupt
endpoints, so urbs should never be automatically resubmitted.
This also fixes a leak of the urb, as submit_int_msg() did not check if
an already re-submitted urb exists before creating a new one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
USB scanning is slow, and there is no need to scan the companion buses
if no usb devices where handed over to the companinon controllers by any
of the main controllers.
This saves e.g. 2 seconds when booting a A10 OLinuxIno Lime with no USB-1
devices plugged into the root usb ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB companion controllers must be scanned after the main controller has
been scanned, so that any devices which the main controller which to hand
over to the companion have actually been handed over before we scan the
companion.
As there are no guarantees that this will magically happen in the right
order, split the scanning of the buses in 2 phases, first main controllers,
and then companion controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move printing of usb scan status to usb_scan_bus().
This is a preparation patch for adding companion controller support to the
usb uclass.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Interrupt endpoints typically are polled for a long time by the usb
controller before they return anything, so calls to submit_int_msg() can
take a long time to complete this.
To avoid this the u-boot code has the an interrupt queue mechanism / API,
add support for this to the driver-model usb code and implement it for the
dm ehci code.
See the added doc comments for more details.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a preparation patch for adding interrupt-queue support to the
ehci dm code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Short circuit the retry loop in legacy_hub_port_reset() by returning an
error from usb_control_msg() when a device was handed over to a companion
by the ehci code. This avoids trying to reset low / fullspeed devices 5
times needlessly. Also do not print an error when a device has been handed
over.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When after a reset the port status connection bit is still set and the enable
bit is not then we're dealing with a full-speed device and should hand it over
to the companion controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add full link training as a fallback in case the fast link training
fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Connect up the clocks and the eDP driver to make these displays work with
Tegra124-based devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This interface is used on laptop devices based on Tegra. Add a driver which
provides access to the eDP interface. The driver uses the display port
uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The SOR is required for talking to eDP LCD panels. Add a driver for this
which will be used by the DisplayPort driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
eDP (Embedded DisplayPort) is a standard widely used in laptops to drive
LCD panels. Add a uclass for this which supports a few simple operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
With the full PMIC framework we may be able to avoid this. But for now
we need access to the PMIC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
As per the author, we don't need this patch really since the other patch
"stm32f4: fix serial output" superseded it.
This reverts commit 85e5f5b7a7.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree support for arm pl010/pl011 driver.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the stm32F4 board's serial ports support.
User can use it easily.
The user only need to edit the number of the usart.
The patch also fix the serial print out.
Last, this version of patch fix the first patch checkpatch.pl error.
Thanks to Kamil Lulko.
Signed-off-by: kunhuahuang <huangkunhua@gmail.com>
This patch fix the serial output.
The source is from Kamil Lulko's "stm32f429-discovery board support"
Thanks, Varcain. I learned a lot.
Signed-off-by: kunhuahuang <huangkunhua@gmail.com>
This patch adds a driver for the PCA9551 LED controller.
Originated-by: Timo Herbrecher <t.herbrecher@gateware.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cc: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Interrupts transfers timing out is normal, so do not log an error for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Add proper cache flushing / invalidating for non cache coherent cpus, for now
only enable this for new (driver-model) usb code to avoid regressions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Non static function and variable declarations do not belong in a .h file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
This is a preparation patch for adding driver-model support.
Note we do keep ohci_dev as a separate struct so that we can later add
support for interrupt-queues which requires allocating a separate ohci_dev
per interrupt-queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
devgone is never assigned a value, so the one comparisson reading it will
never be true, and devgone can be completely removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
The GPIO driver didn't correctly compute the bank offset
from the GPIO number and caused random writes into the
GPIO block address space. Fix the driver so it actually
does the writes correctly. While at it, make use of the
clrsetbits_le32() mechanisms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is a matter of simple additional ifdefery to cater
for the different register layout of the S3C2440 chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Without this usb-1 device descriptors do not get read properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ehci driver model code for finding the first upstream usb-2 hub before
this commit has a number of issues:
1) "if (!ttdev->speed != USB_SPEED_HIGH)" does not work because the '!'
takes presedence over the '!=' this should simply be
"if (ttdev->speed == USB_SPEED_HIGH)"
2) It makes ttdev point to the first upstream usb-2 hub, but ttdev should
point to the last usb-1 device before the first usb-2 hub (when going
upstream from the device), as ttdev is used to find the port of the
first usb-2 hub to which the the last usb-1 device is connected.
3) parent_devnum however should be set to the devnum of the first usb-2
hub, so we need to keep pointers around to both usb_device structs.
To complicate things further during enumeration usb_device.dev will point
to the parent udevice, where as during normal use it will point to
the actual udevice, we must handle both cases correctly.
This commit fixes all this making usb-1 devices attached to usb-2 hubs,
including usb-1 devices attached to usb-1 hubs attached to usb-2 hubs, work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use usb_get_bus in dm ehci code rather then re-implementing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make usb_get_bus easier to use for callers, by directly returning the bus
rather then returning it via a pass-by-ref argument.
This also removes the error checking from the current callers, as
we already have an assert() for bus not being NULL in usb_get_bus().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Do not use bus->seq before device_probe(bus), as bus->seq is not set until
after the device_probe() call. This fixes u-boot printing: "USB-1: " for
each bus it scans.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
dm_gpio_set_dir_flags() will also set gpio output value when switching to
gpio output. So it's not necessary to call dm_gpio_set_value() after
dm_gpio_set_dir_flags() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
