We should not have exported functions in a driver. The i8042_disable()
function is used to disable the keyboard. Provide a remove() method
instead, which is the standard way of disabling a device.
We could potentially add a method to flush input but that does not seem
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are no users of the 64-byte v2 context. The v1 context is
only 16 bytes long and currently an error is raised if too much data is
returned from the EC.
Update the code to limit the size to 16 bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot is started from SPL or TPL, then those earlier phases deal with
the reset cause. On real hardware this cause may be lost once it is read.
Emulate that behaviour in sandbox by reporting a warm reset when a
previous phase has run since start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
We cannot be sure that the interface name takes up the full length of the
space available to it. Use strcpy() instead of memcpy() in this case. This
corrects a valgrind warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
The macros used to set the direction of the GPIO pins are misused,
resulting in a wrong behavior when trying to read the GPIO input level
from U-Boot.
A better macro is also used when setting the output direction.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop BMP_ALIGN_CENTER define in lcd.c and video_bmp.c as it is
already defined by splash.h. Include splash.h in bmp code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.
Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.
Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:
Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 6f57c34473 since it
does not seem to work at least on rk3399.
The Rockchip Technical Reference Manual (TRM) for the rk3399 says the baud
rate prescaler register is readable only when USR[0] is zero. Since this
bit is defined as "reserved" in the socfpga cylcone5 TRM, let's rather
drop this than making the ns16550 debug uart more platform specific.
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
At present line_length is always calculated in video_post_probe(). But
some hardware may use a different line length, e.g. with a 1366-wide
display.
Allow the driver to set this value if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch adds a DM driver for the MPC8xx watchdog.
Basically, the watchdog is enabled by default from the start and
SYPCR register has to be writen once to set the timeout and/or
deactivate the watchdog. Once written, it cannot be written again.
It means that wdt_stop() can be called before wdt_start() to stop the
watchdog, but cannot be called if wdt_start() has been called.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
After this change the m41t62.c can be used with RTC subsystem (i.e. date
command) which uses device model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This change facilitates the conversion of m41t62 RTC driver to device
model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch moves the RTC M41T62 config define to Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds 64-bit addressing support for zynq gem.
This means it can perform send and receive operations on
64-bit address buffers.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the HS400 mode to SDHI driver. This uses the up-tune
mechanism from already supported HS200 tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration
offset, into private data, so it can be passed around. This is done in
preparation for the HS400 mode, which needs to adjust this value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Filter out HS400 support on SoCs where HS400 is not supported yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reorder the tmio_sd_set_clk_rate() function such that it handles all
of the clock requiests correctly. Specifically, before this patch,
clock request with (mmc->clock == 0 && mmc->clk_disable) could leave
the clock enabled, as the function would exit on if (!mmc->clock)
condition on top and will not handle the mmc->clk_disable at all.
Rather than band-aid fixing just that particular problem, reorder
the entire function to make it easier to understand and verify that
all the cases are covered. The function has three sections now:
First, if mmc->clock != 0, we calculate divider for the SD block.
Second, if mmc->clock != 0 and SD block clock are enabled and
current divider is not equal to the new divider, then
stop the clock and update the divider.
Third, if mmc->clk_disable is set, disable the clock, otherwise
enable the clock. This happens independently of divider
update now.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a feature where it can automatically disable clock output
when the bus is not in use. While this is useful, it also interferes with
switching the bus to 1.8V and other background tasks of the SD/MMC cards,
which require clock to be enabled.
This patch respects the mmc->clk_disable and only disables the clock when
the MMC core requests it. Otherwise the clock are continuously generated
on the bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a quirk where divider == 1 must not be set in DDR modes.
Handle this by setting divider to 2, as suggested in the documentation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Switch the driver to using clk_get_rate()/clk_set_rate() instead of
caching the mclk frequency in it's private data. This is required on
the SDHI variant of the controller, where the upstream mclk need to
be adjusted when using UHS modes.
Platforms which do not support clock framework or do not support it
in eg. SPL default to 100 MHz clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
---
V2: - Fix build on certain platforms using SPL without clock framework
V3: - Turn clk_get_rate into a callback and fill it as needed on both
renesas and socionext platforms
Add HS400 properties parsing support to mmc_of_parse().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
The SDHI clock must be configured differently for HS200/HS400/SDR104
modes. Add support for reconfiguring the SDHI clock settings into the
clock driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The USB storage driver does not compile when CONFIG_BLK is set,
but DM_USB is not set, as we're missing the DM device links for
CONFIG_BLK enabled code paths.
So far it looks like nobody fell into this trap, because no board
enabled CONFIG_BLK and CONFIG_USB_STORAGE while not enabling
CONFIG_DM_USB, but we should still reflect that dependency properly
in Kconfig so that implicit enabling of CONFIG_USB_STORAGE works.
Signed-off-by: Alexander Graf <agraf@suse.de>
When an operating system started via bootefi tries to reset or power off
this is done by calling the EFI runtime ResetSystem(). On most ARMv8 system
the actual reset relies on PSCI. Depending on whether the PSCI firmware
resides the hypervisor (EL2) or in the secure monitor (EL3) either an HVC
or an SMC command has to be issued.
The current implementation always uses SMC. This results in crashes on
systems where the PSCI firmware is implemented in the hypervisor, e.g.
qemu-arm64_defconfig.
The logic to decide which call is needed based on the device tree is
already implemented in the PSCI firmware driver. During the EFI runtime
the device driver model is not available. But we can minimize code
duplication by merging the EFI runtime reset and poweroff code with
the PSCI firmware driver.
As the same HVC/SMC problem is also evident for the ARMv8 do_poweroff
and reset_misc routines let's move them into the same code module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Variable 'days' must be defined as signed int. Otherwise the conversion
fails for some dates, e.g. 2004-08-25. Cf function rtc_time64_to_tm() in
the Linux kernel source.
Fixes: 992c1db455 "drivers: rtc: resolve year 2038 problem in rtc_to_tm"
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwBjx8ACgkQfxc6PpAI
rebWEAf+PMc/M3X6cCKm+8P9xTNFv0gv234HVke1eTDG3eyZB6WQnJn5CS0LwyPj
JUfwk4xK0Sqev/sQ6RuzmxmPAgla6UrEFB355tiZRBtFsMgf8bfevOqbxVqMbZl/
bOe4YsFJ3sAgQDuhi2C5xzm2speGtaB8Qy8s1Zlv2sx3zEnLgRqVgeEVHzulZsk3
gAlWKN3ys6EueYnOladjrrvrfOX8SQKYbThI+ACy7suZbtasGRITwP/4fQoXtmOl
39e9WsiW6DBRW1sxNxpixrOS5trgWjOOFiKlY3GNWP+N34+9vYASwuBWwRWqfgXo
cmelT6AcGiPUbHyr4k0CJHKCJlSbaQ==
=p83K
-----END PGP SIGNATURE-----
Merge tag 'pull-30nov18' of git://git.denx.de/u-boot-dm
Fix sound on sandbox
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The "Flamingo" carrier-board for the RK3399-Q7 has a RV3029 populated
and the application will use the off-module RV3029 RTC including the
battery backed SRAM.
To support this use case, this commit includes the following changes:
* updates the rv3029 driver to use DM
* implements the read8/write8 operations
This syncs the implementation with the Linux code (based on 4.17),
porting the trickle-charger support from there (with improvements to
avoid unnecessary EEPROM updates) and adheres to the Linux DTS
binding.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The MicroCrystal RV3029 driver didn't have a Kconfig entry and was not used
anywhere. Add it to Kconfig to make it selectable.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was an incorrect check when looping and finding the first
fast enough frequency in the freq_rang table. The code did
actually return the first that was either exactly correct or
too slow.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was a copy and paste error where the data
enable setting was written to the version register.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Currently the else part of ofnode_get_addr_index function
does not fetch addresses based on the index but rather just
returns the base address. Fix that.
Signed-off-by: Keerthy <j-keerthy@ti.com>
At present these functions are not accessible outside the TPM library, but
in some cases we need to call them. Export them in the header file and add
a define for the SHA1 digest size.
Also adjust tpm_open() to call tpm_close() first so that the TPM is in a
known state before opening (e.g. by a previous phase of U-Boot).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this value is hard-coded in the function that generates a
square wave. Since sample rates vary between different hardware, it makes
more sense to have this as a parameter.
Update the function and its users.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently outputs twice as much data as it should and
overwrites its buffer as a result. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some RTC chips have child drivers, e.g. to provide access to their
non-volatile RAM. Scan for these when binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox i2c works using emulation drivers which are currently children of
the i2c device:
rtc_0: rtc@43 {
reg = <0x43>;
compatible = "sandbox-rtc";
emul {
compatible = "sandbox,i2c-rtc";
};
};
In this case the emulation device is attached to i2c bus on address 0x43
and provides the Real-Time-Clock (RTC) functionality.
However this is not ideal, since every device on an I2C bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
A better approach seems to be to add a separate node on the bus, an
'emulation parent'. This can be given a bogus address (such as 0xff) and
hides all the emulators away. Then we can use a phandle to point from the
device to the correct emualtor, and only on sandbox. The code to find an
emulator does not interfere with normal i2c operation.
Add a new UCLASS_I2C_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. This will be used in a
follow-on patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add two functions which can find a child device by uclass or by name.
The first is useful with Multi-Function-Devices (MFDs) to find one of a
particular type. The second is useful when only the name is known.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function may be useful to code outside of the code driver-model
implementation. Export it and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a newline missing from quite a few printf() strings in these pmic
files. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As a preparation for merging the socfpga gen5 devicetree files
from Linux, this patch makes the dwapb gpio driver work correctly
without the 'bank-name' property on the gpio-controller nodes.
This property is not present in the Linux drivers and thus is not
present in the Linux devicetrees. It is only used to access pins
via bank name.
This fallback is necessary since without it, the driver will
return an error code which will lead to an error in U-Boot
startup.
The bank names will still be added to the default board device
trees in follow-up patch, but other boards using this driver and
not including the bank name should also work with the socfpga.dtsi
without adding the bank-name property.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch adds a DDR3 driver for MT7629 SoC.
Signed-off-by: Wu Zou <wu.zou@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many SoCs from MediaTek have a high-speed uart. This UART is compatible
with the ns16550 in legacy mode. It has extra registers for high-speed
mode which can reach a maximum baudrate at 921600.
However this UART will no longer be compatible if it's in high-speed mode.
Some BootROM of MediaTek's SoCs will change the UART into high-speed mode
and the U-Boot must use this driver to initialize the UART.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7623 SoC. And most of the
structures are used to hold the hardware configuration for each
pin.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a common driver for the Mediatek SoC integrated
watchdog.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock source and clock event for the timer found
on the Mediatek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a driver for MT7623 clock blocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock modules for MediaTek SoCs:
- Shared part: a common driver which contains the general operations
for plls, muxes, dividers and gates so that we can reuse it in future.
- Specific SoC part: the group of structures used to hold the hardware
configuration for each SoC.
We take MT7629 as an example to demonstrate how to implement driver if
any other MediaTek chips would like to use it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop non-dm code and migrate into DM_SPI.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[jagan: Move config menu in DM_SPI area]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Rename platform_data include file as spi_pl022.h from pl022_spi.h,
this is generic notation used for spi platdata include files.
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch can drop unnecessary include files in
pl022_spi driver.
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
pl022 spi driver support both OF_CONTROL and PLATDATA, this
patch is trying to simplify the code that differentiating
platdata vs of_control.
- Move OF_CONTROL code at one place
- Handle clock setup code directly in pl022_spi_ofdata_to_platdata
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This allows building the SPL without driver model for USB. Since
CONFIG_SPL_DM_USB is enabled if and only if CONFIG_DM_USB was enabled
before, this patch does not change the build behaviour.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This debug print was not designed to be active in non-debug mode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the Amlogic AXG SoC pinctrl and GPIO controller
using a specific set of pinctrl functions which differs from the GX SoCs.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson pinctrl needs generic pinctrl, rather than depending on it
select it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In preparation of supporting the new Amlogix AGX SoCs, we need to move
the Amlogic GX pinmux functions out of the common code to be able to
add a different set of SoC specific pinmux functions for AXG.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for disabling subpage write support via
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE.
Currently the Linux Arasan driver does not support subpage writes and in
case of running UBI and accessing the same UBI volume from both U-Boot
and Linux it is required to have the same subpage write configuration
else the location of the UBI headers (EC + VID) will be misaligned
(subpage vs page) and incompatible. Hence the need for disabling
subpage write support in the U-Boot Arasan NAND driver.
Signed-off-by: Martin Lund <malu@gomspace.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds MT7629 qspi driver for accessing SPI NOR flash.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Amlogic Meson SoCs embeds a Flash oriented SPI Controller name SPIFC.
This driver, ported from the Linux meson-spi-spifc driver, add support
for this controller on the Amlogic Meson GX SoCs in U-Boot.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Comment in Linux driver says that clock needs to be doubled only
if we use DDR modes, moreover divider has to be set accordingly.
U-boot driver doesn't declare support for any DDR modes and doesn't
set internal clock divider in CLKCR, so it doubles clock
unconditionally when new mode is used.
Some cards can't handle that and as result SPL fails to load u-boot.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
The initial layout for such NAND chips was the following:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 32 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
This layout has a weakness: reading empty pages trigger ECC errors
(this is expected), but the hardware ECC engine tries to correct the
data anyway and creates itself bitflips, hence bitflips are detected
in erased pages while actually there are none in the NAND chip.
Two solutions have been found at the same time. One was to enlarge the
free OOB area to 64 bytes, changing the layout to be:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 64 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
^^
The very big drawbacks of this solution are:
1/ It prevents booting from NAND.
2/ The current Linux driver (marvell_nand) does not have such problem
because it already re-reads possible empty pages in raw mode before
checking for bitflips. Using different layouts in U-Boot and Linux
would simply not work.
As this driver does support raw reads now and uses it to check for
empty pages, let's forget about this broken hack and return to the
initial layout with only 32 free OOB bytes.
Fixes: ac56a3b30c ("mtd: nand: pxa3xx: add support for 2KB 8-bit flash")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This only applies on BCH path.
When an empty page is read, it triggers an uncorrectable error. While
this is expected, the ECC engine might produce itself bitflips in the
read data under certain layouts. To overcome this situation, always
re-read the entire page in raw mode and check for the whole page to be
empty.
Also report the right number of bitflips if there are any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Raw read support is added by editing a few code sections:
->handle_data_pio() includes the ECC bytes that are not consumed
anymore by the ECC engine.
->prepare_set_command() is changed so that the ECC bytes are
requested as part of the data I/O length.
->drain_fifo() shall also avoid checking the R/B pin too often
when in raw mode.
->read_page_raw()/->read_oob_raw() are written from scratch.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It is useful to be able to invert the colours in some cases so that the
text matches the background colour. Add a parameter to the function to
support this.
It is strange that function takes a private data structure from another
driver as an argument. It seems better to pass the device and have the
function internally work out how to find its required information.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not normally useful, so change the code to avoid writing out every
data package. This can be enabled with #define DEBUG.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds new commands to the EC related to setting and clearing events
as well as controlling power-related settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
The LPC driver expects its buffer to be word-aligned. Add the required
flag to the uclass driver to ensure this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no advantage to using a u8 for function parameters. It forces
the compiler to mask values and can increase code size. Also the command
enum has been extended to 16 bits. Update the functions to use uint
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the device tree is missing a correct spi slave description below
the bus (compatible "spi-flash" or spi-max-frequency are missing),
the 'set_speed' callback can be called with 'speed' == 0 Hz.
At least with cadence qspi, this leads to a division by zero.
Prevent this by initializing speed to 100 kHz in this case (same
fallback value as is done in 'dm_spi_claim_bus') and issue a warning
to console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With drivers that have prefix names that are quite long (like
'versatile_') it is useful to have a wider column for the driver's
name when dumping the device driver tree.
Also update the tests to take into account the wider output format.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the PCIe specification recommend reading the Vendor ID register
to determine if a Function is present, read the Vendor ID of a
non-existent Function must not result in system error, so we'd better
make the first CFG read to Vendor ID instead of Header Type register
in the PCIe enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
clk81 divider is 0 based (meaning that 0 value in the register means
divide by 1). Fix clk81 rate calculation for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add two functions to ADC uclass's:
- adc_raw_to_uV() to ease ADC raw value conversion to microvolts
- adc_channel_mask() to get channels on consumer side
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds watchdog support for the Mediatek MT7621 SoC. The driver
is loosly based on the Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed merge conflict in drivers/watchdog/Kconfig]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The terminal escape sequence ESC [ <x> ; <y> H is used to set the cursor
position. According to the ECMA 48 standard the upper left corner in the
escape sequences is [1, 1]. The video uclass uses [0, 0] as upper left
corner.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix compiler warning
drivers/misc/fs_loader.c:193:9: warning: format ‘%d’ expects
argument of type ‘int’, but argument 5 has type ‘size_t
{aka long unsigned int}’ [-Wformat=]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of two staged ofnode_to_offset followed by
device_get_global_by_of_offset approach, direcly use the
device_get_global_by_ofnode to fetch the device.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add possibility to update the serial parity used.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
K3 based AM654 devices has DDR memory subsystem that comprises
Synopys DDR controller, Synopsis DDR phy and wrapper logic to
intergrate these blocks into the device. This DDR subsystem
provides an interface to external SDRAM devices. Adding support
for the initialization of the external SDRAM devices by
configuring the DDRSS registers and using the buitin PHY
routines.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Change static array to const when it is useful to save memory
(move stm32f7_setup=0x18 from .data to .rodata section)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add get_pin_mux ops support to display the pin muxing
description of the sandbox_pins[]
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds gpio get_function ops support.
This function reports the state of a gpio.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add get_pin_muxing() ops to obtain the pin muxing description
a given pin index.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_name ops to obtain a pin name given a
pin index of a specified pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pins_count ops to obtain the number of pins
owns by a pin-controller.
On STM32 SoCs bindings, each pin-controller owns
several gpio banks. Each GPIO bank can own up to 16 pins.
To obtain the total pins count, walk through each sub-nodes
(ie GPIO banks) and sum each GPIO banks pins number. For that
in probe() we build a list with each GPIO device reference found.
This list will also be used with future get_pin_muxing and get_pin_name
ops to speed up and optimize walk through all GPIO banks.
As this code is common to all STM32 SoCs, this code is put
under SPL_BUILD compilation flag to avoid to increase SPL code size
for STM32F7 which is limited to 32Ko.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Similarly to uclass_first_device_err(), add uclass_next_device_err()
which returns an error if there are no next devices in that uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add pinctrl_get_pin_name() and pinctrl_get_pins_count() methods
to obtain pin's name and pin's muxing given a pin reference.
This will be used by the new pinmux command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_muxing() which allows to display the muxing
of a given pin belonging to a pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.
The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Build option CONFIG_SYS_MAX_NAND_CHIPS is used by NXP LPC32xx NAND MLC
driver only, as a preparation for potential removal or replacement of
the option the change predefines CONFIG_SYS_MAX_NAND_CHIPS to 1, same
value is used by the single user Work Microwave Work 92105 board, thus
it will be safe now to remove the option as a board specific one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The pca953x_gpio driver uses default value of polarity inversion
register. For some devices like PCA9557 and MAX7310, their polarity
inversion register default value is 0xf0. So for high 4 ports, when
reading their values, the values are inverted as the actual level.
This patch clears the polarity inversion register to 0 at init, so
that the port read and write values are aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The earlier commit f4fcba5c5b ("clk: implement clk_set_defaults()")
which introduced the functionality for setting clock defaults such as
rates and parents will skip the processing when executing in a re-reloc
state. This for example can prevent the assigning of clock parents
when running in SPL code. Go ahead and remove this limitation.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
