Commit graph

5014 commits

Author SHA1 Message Date
Wenyou Yang
2c62c56a86 gpio: atmel: Add the PIO4 driver support
The PIO4 is introduced from SAMA5D2, as a new version
for Atmel PIO controller.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2015-11-30 22:27:52 +01:00
Vignesh R
71cbed31f4 am33xx: Remove serial_init in s_init for QSPI/NOR XIP boot
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().

Tested on AM437x IDK EVM with QSPI XIP boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-23 11:01:53 -05:00
Tom Rini
80d307d115 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-11-22 08:20:03 -05:00
Jelle de Jong
aa56cb374d sunxi: Add support for the Lamobo R1 board
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.

The dts file is identical to the one submitted upstream.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:43:58 +01:00
Hans de Goede
d6e6d4b3a9 sunxi: Add H3 dts[i] files
These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Siarhei Siamashka
52d093112a sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
0404d53f2f sunxi: Add H3 DRAM initialization support
Based on existing A23/A33 code and the original H3 boot0.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
1c27b7dcd0 sunxi: Add basic H3 support
Add initial sun8i H3 support, only uart + mmc are supported for now.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:30:59 +01:00
Thomas Chou
9e39003e7f ns16550: move CONFIG_SYS_NS16550 to Kconfig
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2015-11-21 21:50:18 -05:00
Thomas Chou
1874626b2b ns16550: unify serial_tegra
Unify serial_tegra, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-21 21:50:16 -05:00
Thomas Chou
98a51fc3d7 ns16550: unify serial_rockchip
Unify serial_rockchip, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-21 21:50:15 -05:00
Simon Glass
1fa4bfde18 dm: cros_ec: Convert cros_ec keyboard driver to driver model
Adjust the cros_ec keyboard driver to support driver model. Make this the
default for all Exynos boards so that those that use a keyboard will build
correctly with this driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:13:40 -07:00
Simon Glass
f77f5e9be7 dm: tegra: Convert keyboard driver to driver model
Adjust the tegra keyboard driver to support driver model, using the new
uclass. Make this the default for all Tegra boards so that those that use
a keyboard will build correctly with this driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:13:40 -07:00
Tom Rini
9ef671c9d4 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-11-19 13:27:26 -05:00
Michal Simek
a7bcd4c32a zynqmp: mp: Add support for booting R5 from any address
Put jump trampoline to TCM at 0 and setup R5 reset address to 0.
Jump trampoline ensures that jump to the right location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-11-19 10:42:45 +01:00
Nikita Kiryanov
a1e56cf6d4 spl: mmc: add support for BOOT_DEVICE_MMC2
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.

Make SPL take into account the correct mmc device.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-18 14:50:05 -05:00
Nikita Kiryanov
36afd45136 spl: change return values of spl_*_load_image()
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.

Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-18 14:50:02 -05:00
Kipisz, Steven
74cc8b097d board: ti: beagle_x15: Rename to indicate support for TI am57xx evms
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).

Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728

The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.

Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.

NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.

As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-11-18 08:47:03 -05:00
Kevin Smith
490753ace3 arm: mvebu: a38x: serdes specification cleanup
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it.  Also, allow the board to only specify the lanes that are
used instead of including unused lanes.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-11-17 23:41:41 +01:00
Kevin Smith
18c202aa54 arm: mvebu: a38x: Add const to some function calls
Functions that do not modify the pointer passed should declare it
as const.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-11-17 23:41:41 +01:00
Kevin Smith
544acb07ec arm: mvebu: a38x: Remove unsupported topologies
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support.  Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM.  If this needs to be done, it should be
handled in the board file, not in core code.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-11-17 23:41:41 +01:00
Vignesh R
2d13459721 ARM: am43xx: Enable QUAD read and EDMA support for ti_qspi
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-17 23:43:29 +05:30
Tom Rini
98e73c8344 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-11-16 08:35:38 -05:00
Tom Rini
bc80109b11 Merge branch 'master' of git://git.denx.de/u-boot-tegra 2015-11-12 19:32:51 -05:00
Prabhakar Kushwaha
4e4ad6d140 driver: gpio: hikey: Fix pointer conversion warnings for hikey
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
  bank->base = (u8 *)plat->base;

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2015-11-12 15:58:59 -05:00
Peng Fan
f978559c05 imx: mx7: compile misc.c for mx7
Compile misc.c for mx7, since we need related function for
lcdif and nand.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:40:54 +01:00
Peng Fan
623787fd58 imx: imx-common: power down lcdif before boot os
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:40:54 +01:00
Peng Fan
eb111bb31d imx: mx6: implement reset_misc
We need to power down lcdif before uboot reset to make reset can pass
stress test.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:53 +01:00
Peng Fan
a3c252d6d6 video: mxsfb: introduce lcdif_power_down
Introudce a new function lcdif_power_down.

1. Waits for a VSYNC interrupt to guarantee the reset is done at the
   VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
   and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.

The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-11-12 17:40:53 +01:00
Peng Fan
ad153782e0 imx: mx6: add clock api for lcdif
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:53 +01:00
Peng Fan
64ffef05e0 imx: mx6: crm_reg: add LCDIF related macros
Add i.MX6UL/SX LCDIF related macros. Discard uneccessary
'#ifdef xxx'.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:52 +01:00
Peng Fan
b1ce1fb527 imx: mx6: fix register address
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
   LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
   building error for mxsfb.c, since mxsfb.c use imx-regs.h.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:52 +01:00
Peng Fan
8702f5ab5d imx: lcdif: use one register structure for i.MXes
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:38:09 +01:00
Peng Fan
04acd0e5d9 imx: imx-common: move lcdif structure and macro definition to imx-common
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:38:09 +01:00
Peng Fan
eacb287523 imx: include linux/types.h for regs-common.h
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:38:08 +01:00
Peng Fan
6014598f9e mxs: regs-common.h must be wrapped with !__ASSEMBLY__
regs-common.h must be wrapped with #ifndef __ASSEMBLY__

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:38:08 +01:00
Peng Fan
95ae700044 mxs: add parameter base_addr for mxs_set_lcdclk
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-11-12 17:38:08 +01:00
Peng Fan
7de4703691 mx7: psci: add basic psci support
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:31:16 +01:00
Peng Fan
d47cb0b61a arm: discard relocation entries for secure text
The code such as PSCI in section named secure is bundled with
u-boot image, and when bootm, the code will be copied to their
runtime address same to compliation/linking address -
CONFIG_ARMV7_SECURE_BASE.

When compile the PSCI code and link it into the u-boot image,
there will be relocation entries in .rel.dyn section for PSCI.
Actually, we do not needs these relocation entries.

If still keep the relocation entries in .rel.dyn section,
r0 at line 103 and 106 in arch/arm/lib/relocate.S may be an invalid
address which may not support read/write for one SoC.
102         /* relative fix: increase location by offset */
103         add     r0, r0, r4
104         ldr     r1, [r0]
105         add     r1, r1, r4
106         str     r1, [r0]

So discard them to avoid touching the relocation entry in
arch/arm/lib/relocate.S.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-11-12 17:31:02 +01:00
Stephen Warren
e1cf527802 ARM: tegra: note that p2371-2180 is Jetson TX1
p2371-2180 is the engineering board name for the Jetson TX1 developer
kit. Update Kconfig description and help text to make this obvious to
everyone.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:27:16 -07:00
Alexandre Courbot
eca676bd67 ARM: tegra: rename GPU functions
Rename GPU functions to less generic names to avoid potential name
collisions.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Alexandre Courbot
d6bf06c0c7 ARM: tegra: simplify GPU setup
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.

Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Alexandre Courbot
36e5f7ce1c ARM: tegra: remove vpr_configured() function
There is no justification for this function, especially in exported
form.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Stephen Warren
f35cb12511 ARM: tegra: error check Tegra210 XUSB padctl waits
Add code to detect timeouts when waiting for HW events such as PLL
lock done. Any errors are logged and trigger an error return code.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Stephen Warren
4e4b5574fb ARM: tegra: add lane tables to Tegra210 XUSB padctl
Add the tables defining which pads and mux options exist in the Tegra210
XUSB padctl hardware.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Stephen Warren
7a908c7e01 ARM: tegra: switch Tegra210 to common XUSB padctl
This change simply deletes code from the Tegra210 XUSB padctl driver that
is already present in the common XUSB padctl code. Since all the arrays
in tegra210_socdata are empty, this update may leave the Tegra210 XUSB
padctl driver non-functional at run-time. However, (a) this driver is not
used yet so no regression can be observed and (b) the next commit will
immediately fix this up.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00
Stephen Warren
095e65839e ARM: tegra: parameterize common XUSB code
There are some differences between the Tegra124 and Tegra210 XUSB padctl
code. So far, the common XUSB padctl code only supports Tegra124. Add
some parameters etc. so that it can work for both chips.

This also allows moving Tegra124's process_nodes() into the common file;
something that would have requires edits during the move if done in the
previous commit.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00
Stephen Warren
1680d7b6de ARM: tegra: create common XUSB padctl driver file
A fair amount of the XUSB padctl driver will be common between Tegra124
and Tegra210. To avoid cut/paste between the two chips, create a new
file that will contain the common code, and convert the Tegra124 code to
use it. This change doesn't move every last piece of code that can/will be
shared, but rather concentrates on moving code that can be moved with zero
changes, so there are no other diffs mixed in.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00
Stephen Warren
057fd32ffc ARM: tegra: clean up XUSB padctl error() calls
This file defines pr_fmt(), so the individual error() calls don't need to
include the prefix in their format strings. Doing so results in duplicate
text in any error messages. Remove the duplication.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00
Stephen Warren
aae52c000f ARM: tegra: rename dummy XUSB padctl implementation
A future patch will soon move some of the XUSB padctl code into a common
file in arch/arm/mach-tegra. Rename the existing dummy XUSB padctl file
to avoid conflicting with that, or being confusing.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00