Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.
The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.
Additionally, the following board intentionally omits the property
because VBUS is always enabled:
- Nintendo_NES_Classic_Edition_defconfig /
sun8i-r16-nintendo-nes-classic
The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The vexpress64 board family now relies on OF_CONTROL and
OF_HAS_PRIOR_STAGE, so platform-specific configuration requirements
are minimal.
The vexpress_aemv8a_semi_defconfig file defines many flags that are not
needed for a minimal boot, such as flash memory configuration.
Therefore create vexpress_fvp_defconfig which contains the minimum
configuration required to boot on an Arm v8a FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
- watchdog: arm_smc_wdt: add watchdog support (Lionel)
- watchdog: ftwdt010: return a previously deleted driver now ported to
DM (Sergei)
- watchdog: Add a watchdog driver for Raspberry Pi boards (Etienne)
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
enable commands for i2c/pmic/regulator and relevant configs.
also drop configs for unused regulators.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using DMA to load TF-A into SRAM fails when booting from eMMC on RK3588.
## Checking hash(es) for Image atf-3 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-3' image node
spl_load_simple_fit: can't load image loadables index 2 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
Fix this by using PIO mode in SPL and limit the number of blocks used in
a single read command to avoid triggering Data End Bit Error interrupt.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from a SD-card on ROCK 5 Model B fails to load atf using
DMA and prints debug_uart messages.
<debug_uart>
<debug_uart>
U-Boot SPL 2023.04-rc3 (Mar 12 2023 - 00:30:16 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-1' image node
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Use fifo-mode to disable DMA in SPL, add same-as-spl to boot-order and
remove DEBUG_UART_ANNOUNCE option to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable usb support in the mk808_defconfig.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the Rockchip rk3066a u-boot-tpl.bin file needs
to add the characters "RK30", while the other SoCs replace
the first 4 bytes. Bring this in line with the rest by
lowering CONFIG_TPL_TEXT_BASE and update rockchip.rst
instructions.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on RK3588 SoCs using U-Boot TPL
and instead an external TPL binary must be used to generate a bootable
u-boot-rockchip.bin image.
Enable ROCKCHIP_EXTERNAL_TPL by default for RK3588, add build steps for
RK3588 to documentation and clean up CONFIG_BINMAN_FDT options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Puma RK3399 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Without CONFIG_EFI_CAPSULE_AUTHENTICATE=y the following tests are skipped:
* test/py/tests/test_efi_capsule/test_capsule_firmware_signed_fit.py
* test/py/tests/test_efi_capsule/test_capsule_firmware_signed_raw.py
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the initial basic config for StarFive VisionFive v2 board. It
includes consol, Norflash, sdio, ddr etc.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
With some USB devices connected on USB HUB for the STMicroelectronics
boards, set the usb_pgood_delay=2 is not enough to ensure a correct
detection for all cases; but it is solved with USB_HUB_DEBOUNCE_TIMEOUT=2s.
For example, issue encountered with the USB flash disk:
ID 058f:6387 Alcor Micro Corp. Flash Drive
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The early malloc usage increased so the associated defined
CONFIG_SYS_MALLOC_F_LEN need to be increased.
For example, for stm32mp15_defconfig and
stm32mp157c-dk2-scmi.dtsi, we have:
Early malloc usage: 280b8 / 80000
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The ftwdt010 watchdog driver was deleted by
commit 11232139e3 ("nds32: Remove the architecture")
Return it to the codebase in a DM compatible form. Enable it in
sandbox_defconfig to test compilability.
Another platform using ftwdt010 will be submitted later.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
-----BEGIN PGP SIGNATURE-----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=Vf7Q
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20230417' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add initial support for BPI-CM4
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----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=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
Add configuration for the Beelink GT1 Ultimate board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Karl Chan <exxxxkc@getgoogleoff.me>
Link: https://lore.kernel.org/r/e3c87efd-4ac1-24a7-503d-71669aae5177@yahoo.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configurations for the WeTek Hub and WeTek Play2 boards.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-14-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration for the BananaPi M2-Pro board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-5-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for both the BananaPi BPI-CM4 module and the BananaPi
baseboard which is compatible with the RaspberryPi CM4IO baseboard.
The BananaPi BPI-CM4 module follows the CM4 specifications at [1],
but with a single HDMI port and a single DSI output.
The current CM4IO baseboard DT should work fine on the Raspberry CM4
baseboard and other derivatives baseboards, but proper DT should
be written for other baseboards.
[1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Link: https://lore.kernel.org/r/20230307-u-boot-cm4-v1-2-43f5a393cd37@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable Renesas RSwitch driver, matching SERDES PHY driver and Marvell
10G ethernet PHY driver in R8A779F0 S4 Spider board configuration to
make ethernet available via the RSwitch ports.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current shell prompt '->' interferes with CI matching on 'bdinfo'
output. When CI test.py attempts to locate memory information in the
'bdinfo' output, it matches on '->' prefix which is identical to the
shell prefix. Switch the prompt to default '=>' one to avoid this
interference.
Suggested-by: Tom Rini <trini@konsulko.com> # found the CI oddity
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the early days of the Allwinner A64 U-Boot support, we relied on a
vendor provided "boot0" binary to perform the DRAM initialisation. This
replaced the SPL, and required to equip the U-Boot (proper) binary with
a vendor specific header to be recognised as a valid boot0 payload.
Fortunately these days are long gone (we gained SPL and DRAM support in
early 2017!), and we never needed to use that hack on any later 64-bit
Allwinner SoC.
Since this is highly obsolete by now, remove that option from the
defconfigs of all A64 boards. We leave the code still in here for now,
since some people expressed their interest in this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Part of the code, previously known as "unknown feature", also doesn't
have constant values. They are derived from TPR0 parameter in vendor
DRAM code.
Let's move that code to separate function and introduce TPR0 parameter
here too, to ease adding new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These values are highly board specific and thus make sense to add
parameter for them. To ease adding support for new boards, let's make
them same as in vendor DRAM settings.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor DRAM settings use TPR10 parameter to enable various features.
There are many mores features that just those that are currently
mentioned. Since new will be added later and most are not known, let's
reuse value from vendor DRAM driver as-is. This will also help adding
support for new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While ODT values for same memory type are similar, they are not
necessary the same. Let's parameterize them and make parameter same as
in vendor DRAM settings. That way it will be easy to introduce new board
support.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
