System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.
All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.
Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).
NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).
i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
Linux requires to describe nand structure under nand controller.
If it is not described nand device is not detected by Linux.
Error shown by Linux kernel:
pl35x-nand-controller e1000000.nand-controller: Incorrect number of NAND chips (0)
pl35x-nand-controller: probe of e1000000.nand-controller failed with error -22
When wired:
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3fcd68ccdfed5e6c079681e3b29e06583ec8a375.1695378830.git.michal.simek@amd.com
The DPSUB DT bindings now specify ports to model the connections with
the programmable logic and the DisplayPort output. Add them to the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1c91420e90bc823d7529834c33438216857c7161.1695378830.git.michal.simek@amd.com
Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/02f308c774d4f2a798a9a8c066824114a19841a7.1695378830.git.michal.simek@amd.com
All zynqmp boards have been already described via mdio node that's why also
convert the rest of the boards. With using mdio node there is an option to
add reset property for the whole mdio bus which is reflected by
's/phy-reset-gpios/reset-gpios/g' for some boards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ff165281a70a38e2b76fee91e6255ce95ce8021b.1695378830.git.michal.simek@amd.com
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all
to required pinctrl nodes to simplify use of the prevent booting on
power plug-in option in SPL.
With the following Kconfig options and nodes in u-boot.dtsi the prevent
booting on power plug-in option can work in SPL.
CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PMIC_RK8XX=y
&i2c0 {
bootph-pre-ram;
};
&rk817 {
bootph-pre-ram;
regulators {
bootph-pre-ram;
};
};
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Add support for generating a LZMA-compressed U-boot binary with the
help of binman, if CONFIG_SPL_LZMA is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for generating a GZIP-compressed U-boot binary with the
help of binman, if CONFIG_SPL_GZIP is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on rk3308 SoC using U-Boot
TPL or SPL, and therefore an external TPL binary must be used to
package a bootable u-boot-rockchip.bin image.
Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308.
Remove useless TPL_SERIAL.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Enable CONFIG_TPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_TPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_SPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which eventually calls
dm_timer_init() to grab the tick-timer, which is mcu_timer0. Since we
need to set up the clocks before using the timer, move clk_k3 driver
probe before k3_sysfw_loader to ensure we have all necessary clocks set
up before.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
U-Boot uses mcu_timer0 as the tick-timer, so add it to device list.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warnings:
<stdout>: Warning (reg_format): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f4000/ethernet@8000000/mdio@f00: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0100:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0000:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (phys_property): /bus@f4000/ethernet@8000000/ethernet-ports/port@2:phys: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move cbass_mcu node to -r5-sk.dts as it is only required
for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----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=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
stm32mp135f-dk board has a type-c connector to retrieve the connection
state. For now, simply force an active peripheral mode in u-boot for
flashing.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v6.6.rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
commit 6b443faa313c519db755ff90be32758fd9c66453 Linux upstream.
This is a preparation patch for the upcoming support to manage CAN
peripherals in single configuration.
The addition ensures backwards compatibility.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 559a6e75b4bcf0fc9e41d34865e72cf742f67d8e Linux upstream.
Add pin configurations for using CAN controller on stm32f469-disco
board. They are located on the Arduino compatible connector CN5 (CAN1)
and on the extension connector CN12 (CAN2).
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230328073328.3949796-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7355ad1950f41e755e6dc451834be3b94f82acd4 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F429. The
chip contains two CAN peripherals, CAN1 the primary and CAN2 the secondary,
that share some of the required logic like clock and filters. This means
that the secondary CAN can't be used without the primary CAN.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230328073328.3949796-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 10a970bc3ebfa ("ARM: dts:
stm32: support display on stm32f746-disco board") and removes the same
settings from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit e4e724099f04072053cf411456e3e9aae48c4af1 Linux upstream.
In the schematics of document UM1907, the power supply for the micro SD
card is the same 3v3 voltage that is used to power other devices on the
board. By generalizing the name of the voltage regulator, it can be
referenced by other nodes in the device tree without creating
misunderstandings.
This patch is preparatory for future developments.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 008ef8b3a1a00 ("Add LTDC
(Lcd-tft Display Controller) support") and removes the same settings
from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit f0215440069c4fb12958d2d321e05faa2708a11d Linux upstream.
The patch adds support for touchscreen on the stm32f746-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7a5f349e592c254f3c1ac34665b6c3905576efc2 Linux upstream.
The patch replaces the number 12 with the appropriate numerical constant
already defined in the file stm32f7-rcc.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 0920ccdf41e3078a4dd2567eb905ea154bc826e6 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
* CAN1: Primary bxCAN for managing the communication between a secondary
bxCAN and the 512-byte SRAM memory.
* CAN2: Secondary bxCAN with no direct access to the SRAM memory.
This means that the two bxCAN cells share the 512-byte SRAM memory and
CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
* CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
512-byte SRAM memory.
-------------------------------------------------------------------------
| features | CAN1 | CAN2 | CAN 3 |
-------------------------------------------------------------------------
| SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte |
-------------------------------------------------------------------------
| Filters | 26 filters shared between CAN1 & CAN2 | 14 filters |
-------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 011644249686f2675e142519cd59e81e04cfc231 Linux upstream.
Add pin configurations for using CAN controller on stm32f7.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize RZ R8A774E1 RZ/G2H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774C0 RZ/G2E DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774B1 RZ/G2N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774A1 RZ/G2M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Synchronize RZ R7S72100 RZ/A1 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77995 D3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77980 V3H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77965 M3-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77951 H3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7794 E2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7790 H2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 65cc0e2a65 ("global: Move remaining CONFIG_SYS_* to CFG_SYS_*")
renamed CONFIG_SYS_UBOOT_START to CFG_SYS_UBOOT_START. Unfortunately,
this meant that the value was no longer available to the Makefile. This
caused imxrt to fail to boot. All the other boards that used this
variable were unaffected because they were using the default value
which is CONFIG_TEXT_BASE.
This commit converts CFG_SYS_UBOOT_START to Kconfig and sets the default
value to CONFIG_TEXT_BASE.
Suggested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dm tree enhancement
adjust meaning of bootph-pre-ram/sram
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUPQXURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY1TAf+LeDzKKMhJmyo5ImQWlKPdFt9UGlWqthL
PBngUWV7GdQ5Kn+dLmKmySAmnQC4XNid565nJt8okmMfpHYUBhOnrnJmrXTZdDPJ
lYrpEAR7fTyTTTwjSVFcIXJ56bIT07AUX6jQATh383+Plm0U15tRBMguNsrTy1wL
EmJBVdeT0BZkpSkJyqAIkVuwjOYP+KSuVCectL5LRIpKtjOA+HmMGmELUirjuL00
uN2h/uucuSGFnjCmKW4l9sYrxxYgd/zN2Y8SOJwBebKyHxSgyvNdbjZxeG5o3gSS
ruUSEx4DHYVIRHeDBAnwB4wLdCOqfC2dy0ACReTg0Li+iSQN9qYtEg==
=Sl3P
-----END PGP SIGNATURE-----
Merge tag 'dm-next-23sep23' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
buildman file-keeping and build-progress improvements
dm tree enhancement
adjust meaning of bootph-pre-ram/sram
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
Trying to boot a fitImage after a successful hab_auth_img operation
causes the following error:
## Loading kernel from FIT Image at 88000000 ...
Using 'conf-imx7d-smegw01.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x8800010c
Data Size: 9901752 Bytes = 9.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80800000
Entry Point: 0x80800000
Hash algo: sha256
Hash value: 28f8779bbf010780f16dd3d84ecb9b604c44c5c2cf7acd098c264a2d3f68e969
Verifying Hash Integrity ... sha256Error in SEC deq
CAAM was not setup properly or it is faulty error!
The reason for this error is that the BootROM uses the CAAM Job Ring 0,
so disable its node in U-Boot to avoid the resource conflict.
imx8m dtsi files also have the Job Ring 0 disable since the following
kernel commit:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch?h=v6.5&id=dc9c1ceb555ff661e6fc1081434600771f29657c
For a temporary solution, disable the Job Ring 0 in imx7s-u-boot.dtsi.
Reported-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ivt_offset parameter is optional for both hab_auth_img_or_fail
and hab_auth_img commands.
Document it in their usage texts to make it clearer.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit ea91031b22 ("imx: hab: extend hab_auth_img to calculate
ivt_offset"), it is possible to call the hab_auth_img command without the
last ivt_offset argument.
Currently, calling hab_auth_img_or_fail without the last
ivt_offset parameter causes a failure and the command usage text is shown.
Fix this problem by adjusting the argc logic to allow
calling hab_auth_img_or_fail with only the address and size parameters.
This way, both hab_auth_img and hab_auth_img_or_fail have the same
behavior with respect to the allowed number of command parameters.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
If CMD_ELF disabled and IMX_BOOTAUX enabled, the u-boot building ends
up with a linking error [1]. Select LIB_ELF to fix the building
issue.
[1]
ld: /tmp/ccaF1rpv.ltrans0.ltrans.o: in function `do_bootaux':
arch/arm/mach-imx/imx_bootaux.c:108: undefined reference to `valid_elf_image'
Fixes: c0f037f6a2 ("mach-imx: bootaux: elf firmware support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Remember where these end up so that we can pass this information on to
the EFI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When CONFIG_CMD_USB and CONFIG_USB are disabled, still some compilation
errors are seen as below.
In file included from include/configs/xilinx_zynqmp.h:173,
from include/config.h:3,
from include/common.h:16,
from env/common.c:10:
include/config_distro_bootcmd.h:302:9: error: expected '}' before 'BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:302:9: note: in definition of macro
'BOOTENV_DEV_NAME_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:77:41: note: in expansion of macro
'BOOTENV_DEV_NAME'
77 | # define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
func(USB, usb, 1)
| ^~~~
include/configs/xilinx_zynqmp.h:168:9: note: in expansion of macro
'BOOT_TARGET_DEVICES_USB'
168 | BOOT_TARGET_DEVICES_USB(func) \
| ^~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:454:25: note: in expansion of macro
'BOOT_TARGET_DEVICES'
454 | "boot_targets=" BOOT_TARGET_DEVICES(BOOTENV_DEV_NAME) "\0"
| ^~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:474:9: note: in expansion of macro
'BOOTENV_BOOT_TARGETS'
474 | BOOTENV_BOOT_TARGETS \
| ^~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:179:9: note: in expansion of macro
'BOOTENV'
179 | BOOTENV
| ^~~~~~~
include/env_default.h:120:9: note: in expansion of macro
'CFG_EXTRA_ENV_SETTINGS'
120 | CFG_EXTRA_ENV_SETTINGS
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from env/common.c:32:
include/env_default.h:27:36: note: to match this '{'
27 | const char default_environment[] = {
| ^
scripts/Makefile.build:256: recipe for target 'env/common.o' failed
make[1]: *** [env/common.o] Error 1
Makefile:1853: recipe for target 'env' failed
make: *** [env] Error 2
make: *** Waiting for unfinished jobs....
Add CONFIG_USB_STORAGE as dependency for USB related macro's such as
BOOT_TARGET_DEVICES_USB() and DFU_DEFAULT_POLL_TIMEOUT and
CONFIG_THOR_RESET_OFF.
Remove CONFIG_ZYNQMP_USB from Kconfig and also from defconfig since it
is not used anywhere else.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230904031528.11817-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Correct the i2c address for si570 oscillator that generates the si570_user1
clock. i2c address was changed by commit b6a8c603d680 ("arm64: zynqmp: Fix
i2c addresses for vck190 SC") because address in node name wasn't aligned
with reg property. But actual 0x5f address is correct which is quite rare
because all other si570s are at 0x5d.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6f31881b0e2dd657f0d4ff0869c009c2e1224f22.1694441445.git.michal.simek@amd.com
Added no-wp DT property in OSPI flash node for all board dts & dtsi files
on which the WP# signal of the OSPI flash device is not connected. If this
property is set, then the software will avoid setting the status register
write disable (SRWD) bit in status register during status register
write operation.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e88dd7b9306bdf0738b2248bf9017e1997d25dc.1694441445.git.michal.simek@amd.com
xlnx,mio_bank was used in past but it was renamed to xlnx,mio-bank because
'_' in property shoudln't be used. There is no impact on the platform
because if the properly is not defined bank 0 is default. Bank 0 and 1 have
the same configuration that's why there shouldn't be any issue.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ace68d4b7701d1606a85cb18242409fce941b363.1694441445.git.michal.simek@amd.com
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
Revision 2 is SW compatible with revision 1 but it is necessary to reflect
it in model and compatible properties which are parsed by user space.
Rev 2 has improved a power on boot reset and MIO34 shutdown glich
improvement done via an additional filter in the GreenPak chip.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6b9e68ebfb436da391daeb147f2a9985ac984c0c.1692951005.git.michal.simek@amd.com
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c052ddf39e392e97f87f1c57ea06f3508733c672.1692947486.git.michal.simek@amd.com
This moves the aes operation that is performed by the pmu into a
separate file. This way it can be called not just from the shell
command, but also e.g. from board initialization code.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Link: https://lore.kernel.org/r/20230725072658.16341-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
NOTE: sync with v6.6-rc1 will bring in this change naturally.
Signed-off-by: Nishanth Menon <nm@ti.com>
Introduce the new serdes header from kernel v6.6-rc1
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Signed-off-by: Nishanth Menon <nm@ti.com>
In 2cb43ef1c2 ("usb: ether: Fix error handling in usb_ether_init") the error
handling of usb_ether_init() was changed. Not a single other call site of this
function checks its return value, therefore follow suit in the am33xx code.
Do not cause the boot to halt if the usb gadget ethernet initialization fails:
initcall sequence 9ffdbd84 failed at call 808024b9 (err=-19)
### ERROR ### Please RESET the board ###
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Michal Suchánek <msuchanek@suse.de>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The usb_gadget_handle_interrupts() is no longer used anywhere,
replace the remaining uses with dm_usb_gadget_handle_interrupts()
which takes udevice as a parameter.
Some of the UDC drivers currently ignore the index parameter altogether,
those also ignore the udevice and have to be reworked. Other like the
dwc3_uboot_handle_interrupt() had to be switched from index to udevice
look up to avoid breakage.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
Signed-off-by: Marek Vasut <marex@denx.de>
To have the WDIOF_CARDRESET support for the TI AM65x platform watchdog,
this patch reserves some memories, which indicate if the current boot due
to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Update the DDR settings to those generated using 0.10 version of Jacinto
7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
baseline of base device tree is v6.5-rc1.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
While at this, drop the extraneous whitespace.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
The erratum is called locally, make it static, drop the #ifdeffery since
it will only be called in R5 build and mark it potentially unused to
stop compiler screaming at us.
While at this, drop the redundant return for a void function.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Drop the #ifdeffery and use IS_ENABLED() inline check and let the compiler
do it's thing.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Clean the function up a bit further. Return immediately on match
and return ARRAY_SIZE() - 1 on failure. Add proper comment in that
case.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This platform is behind on migrations (it is the sole user of the oldest
legacy version of the USB gadget stack and is long overdue for
migration) and with Pali no longer being a maintainer, we remove this
platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
If dram_init_banksize() is called from SPL, the rom_pointer, at that
point, is not correctly initialized. This causes wrong calculation of
DRAM start and size in dram_init_banksize(). The issue became apparent
only in Falcon Mode. Added an extra condition to prevent using
rom_pointer in SPL.
Signed-off-by: Elena Popa <elena.popa@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Use the misc_init_f event instead, which is designed for this purpose.
All boards with CONFIG_VID already enable CONFIG_EVENT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Add a newline at the end of the dts, without which the build fails
when including a dtsi file.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Button works out of the box now if the following config options are
enabled: CONFIG_BUTTON, CONFIG_BUTTON_GPIO, CONFIG_CMD_BUTTON,
CONFIG_DM_GPIO.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
If CONFIG_LED and CONFIG_LED_GPIO are enabled, it is not necessary to
initialize the RGB LED on the board by manually setting hardcoded GPIOs
anymore. Everything is well defined in dts and can be used like on
boards of other vendors.
Keep the old behaviour as fallback, though.
With all this in place enabling CONFIG_CMD_LED gives us a working 'led'
command on the U-Boot shell.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This reverts commit c5b68ef8af.
CONFIG_OPTEE_TZDRAM_SIZE is used by imx6-based SoCs as well. Move the
option back.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Adding a phandle to a template node is not allowed, since when the node is
instantiated multiple times, we end up with duplicate phandles.
Drop this invalid constructs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
CFG_STM32MP1_SCMI_SHM_SYSRAM will be disabled by default for STM32MP13x
SoCs in next OP-TEE version and the OP-TEE SMCI server uses the OP-TEE
native shared memory registered by clients.
To be compatible by default with this configuration this patch removes
the shared memory in the SCMI configuration and the associated reserved
memory in SRAM.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since OP-TEE commit 89ba3422ee80 ("plat-stm32mp1: scmi_server: default
use OP-TEE shared memory"), integrated in OP-TEE 3.22.0-rc1
the default configuration for STM32MP15x SoCs changes,
CFG_STM32MP1_SCMI_SHM_SYSRAM is disabled by default and the OP-TEE SMCI
server uses ithe OP-TEE native shared memory registered by clients.
To be compatible by default with this configuration and the next OP-TEE
version, this patch removes the SHMEM in the SCMI configuration and the
associated reserved memory in the last 4KByte page of SRAM,
in the STM32MP15 device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit 02be57caf7 ("riscv: qemu: Enable usb keyboard as an input
device") adds PCI xHCI support to QEMU RISC-V virtual machines and
enables using a USB keyboard as one of the input devices. Similarly,
enable those for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 608b80b5b8 ("riscv: qemu: Enable PRE_CONSOLE_BUFFER") enables
buffering console messages for QEMU RISC-V virtual machines so those
printed before the video console is available will still show up on the
display. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 716161663e ("riscv: qemu: Enable Bochs video support") enables
a video console for QEMU RISC-V virtual machines using an emulated Bochs
VGA card. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
In rmobile_cpuinfo_idx() there is an off-by-one error in accessing the
rmobile_cpuinfo array.
At the end of the loop, i is equal to the array size, i.e.
rmobile_cpuinfo[i] accesses one entry past the end of the array. The
last entry in the array is a fallback value so the loop should count to
ARRAY_SIZE(rmobile_cpuinfo) - 1 instead, this will leave i equal to the
index of the fallback value if no match is found.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmTfWrITHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYPFD/9hw40HjaAXf6cD960HWSlcGuNOIV99
A9JoSgHipCuhACr0z7s4MpbATjEgknZUblJNiVdhzCWAgW3Spy9JpSxMyKlpqdiH
7Z971DuaXFX9ZCilX9g6whZI/RDglpUEjt3cb4PWrznM6dpKA73voizo+czBeXd7
AhxTN/2I89VLz75RyR+X41bLLK1VuGND+uGHz/DDbpMXEW8gVRtZ8gnJPeR4zg1y
EUacNFc+PVjghMFZGmClnw0pXkq2akKp5cJ/A+11aa/Q7FII63v5/Np79kDtnUje
GPSdg4yqSr1ZE/6qK0qV58B2KKHfeg+6GC47s46KjzaUwL4De64zHtCt6t37zz8y
hngeeR5SYIKR8HkpXKM8DsMv0D1WciP2awggFPaPF802H/5GMVCnEFITmuFlOuAe
Q1lg2acywMo2NFINMOONuQahGIJZORpm2VMonMhlesyAuc89quslt/iYSAoV9E4/
Pt1AqgeOpUh5I236EygJJ11V2BAXkwzR6RazFDr3AHCqB9iFW/UNS1Y7A1pXwKYN
IVUWU8xkuYYSyxeGwuIrTj/JdQhwfO0jn+xn5g+rUPWNP5n4FJ2oBVPOInfEpled
k0HgxcGK6Z0hBCwd6/t03QQJWD47/r5jAd9x1eLRFWYV8ivl2Acvm+MlkPx81weG
E1h7UKdfvTZcDw==
=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
MT7988 has a t-phy and an x-phy controller. There is already a driver for
t-phy so we can add USB support for this phy type.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Builds for Raspberry Pi targets fail when CONFIG_DISPLAY_CPUINFO is
enabled and following error can be seen -
common/board_f.o:(.rodata.init_sequence_f+0x90):
undefined reference to `print_cpuinfo'
Added implementation of function "print_cpuinfo"
Signed-off-by: Naveen Kumar Chaudhary <naveenchaudhary2010@hotmail.com>
