Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fixed wrong PHY Interface Mode
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
The correct compatible for this eeproms is microchip,24aa02e48
The previous compatible string was working up to U-boot 2020.04.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
The USB support is not by default enabled on all designs, so it does not
make seance to have USB specific erratum's enabled on such a designs.
On our internal Hitachi-Powergrids design not using the USB controller
there is a crash when accessing those specific memory locations selected
by the erratum flags.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Check for NULL return value from fdt_getprop() in
fdt_fixup_remove_jr()
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
[Fixed checkpatch errors/warnings]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The AT91 architecture now has two possible timer blocks, the old PIT timer
and the new PIT64B.
The timer.c file has an old non DM driver that works for platforms
that do not use the ATMEL_PIT_TIMER DM-based driver.
Update the Makefile to select this old driver in case neither of the
ATMEL_PIT_TIMER and the MCHP_PIT64B_TIMER are selected.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA7G5 uses CCF driver under drivers/clk/at91/ and not the custom older
at91 clock.c driver. Remove it from the compilation list and adapt cpu.c
arch_cpu_init() to avoid calling at91_clock_init() which is wrong
anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Align the pin setup for sdhci0 with linux kernel.
This means to have slew rate enable and high drive strength.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
