- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If we are running in EL2 skip PSCI implementation setup. This avoids an
exception if CONFIG_ARMV8_PSCI is set, but u-boot is started by TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a Kconfig for this erratum, but it is ignored for armv8.
Respect it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Based on current usage, migrate a number of DP-DDR related options to
Kconfig.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the semihosting_enabled function to determine whether or not to
enable semihosting devices. This allows for graceful fallback in the
event a debugger is not attached.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This register holds "pstate" which includes (among other things) the
instruction mode the CPU was in when the exception was taken. This is
necessary to correctly interpret instructions at elr.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ARMV8_SWITCH_TO_EL1
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This converts the following to Kconfig:
CONFIG_ARMV7_SECURE_BASE
CONFIG_ARMV7_SECURE_MAX_SIZE
CONFIG_ARMV7_SECURE_RESERVE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 88998f7775 ("arm: arm926ej-s: Add sunxi code") introduced
the ARM926 version of the code to save and restore some FEL state, to
be able to return to the BROM FEL code after the SPL has run.
However during review a change was made, that happened to mess up the
register restore part, so SCTLR and CPSR ended up with the wrong values,
breaking return to FEL.
Use the same offset that we actually save those registers to, to make
FEL booting actually work on the Lichee Pi Nano.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.
The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.
Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.
Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In ARMv8 we have the choice between two stack pointers to use: SP_EL0 or
SP_ELx, which is banked per exception level. This choice is stored in
the SP field of PState, and can be read and set via the SPSel special
register. When the CPU takes an exception, it automatically switches to
the SP_ELx stack pointer.
Trusted Firmware enters U-Boot typically with SPSel set to 1, so we use
SP_ELx all along as our sole stack pointer, both for normal operation and
for exceptions.
But if we now for some reason enter U-Boot with SPSel cleared, we will
setup and use SP_EL0, which is fine, but leaves SP_ELx uninitialised.
When we now take an exception, we try to save the GPRs to some undefined
location, which will usually end badly.
To make sure we always have SP_ELx pointing to some memory, set SPSel
to 1 in the early boot code, to ensure safe operation at all times.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv8 architecture describes the "SError interrupt" as the fourth
kind of exception, next to synchronous exceptions, IRQs, and FIQs.
Those SErrors signal exceptional conditions from which the system might
not easily recover, and are normally generated by the interconnect as a
response to some bus error. A typical situation is access to a
non-existing memory address or device, but it might be deliberately
triggered by a device as well.
The SError interrupt replaces the Armv7 asynchronous abort.
Trusted Firmware enters U-Boot (BL33) typically with SErrors masked,
and we never enable them. However any SError condition still triggers
the SError interrupt, and this condition stays pending, it just won't be
handled. If now later on the Linux kernel unmasks the "A" bit in PState,
it will immediately take the exception, leading to a kernel crash.
This leaves many people scratching their head about the reason for
this, and leads to long debug sessions, possibly looking at the wrong
places (the kernel, but not U-Boot).
To avoid the situation, just unmask SErrors early in the ARMv8 boot
process, so that the U-Boot exception handlers reports them in a timely
manner. As SErrors are typically asynchronous, the register dump does
not need to point at the actual culprit, but it should happen very
shortly after the condition.
For those exceptions to be taken, we also need to route them to EL2,
if U-Boot is running in this exception level.
This removes the respective code snippet from the Freescale lowlevel
routine, as this is now handled in generic ARMv8 code.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With the current configuration provided in mxsimage{-spl}.mx28.cfg the
size of SPL binary has been constrained to 32 KiB, due to "LOAD IVT"
command with 0x8000 offset.
The problem was that, the imx28 ROM takes the u-boot.sb and then
extracts from it the IVT header and places it on the 0x8000 OCRAM offset
overwriting any valid (i.e. loaded from eMMC or SPI-NOR) SPL code. This
bug was unnoticed as the overwrite size was just 32 bytes, so the
probability that some important code is altered was low.
However, in the XEA board (where the SPL size is ~39KiB), the overwritten
data was `(struct dm_spi_ops *) 0x800c <mxs_spi_ops>`, which is used
during the boot process.
As a result the SPL execution code hanged with "undefined instruction"
abort as callbacks (with wrong addresses) from it were called.
The fix is to change the OCRAM's offset where IVT is loaded to 0xE000,
so the SPL can grow up to ~57KiB (the maximal size of OCRAM memory
available is 0xE3FC).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The imx28 uses following voltage supplies hierarchy:
VDD_5V (VDD_BAT) -> VDDIO -> VDDA -> VDDMEM
\-----> VDDD
One shall first enable DCDC on the parent source (VDDIO) and then
follow with its children.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Some Allwinner SoCs use ARM926EJ-S core.
Add Allwinner/sunXi specific code to ARM926EJ-S CPU dircetory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both armv7 and arm926ejs use this timer code so move it to mach-sunxi.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv7 start code has support for saving some boot params at the
entry point, which is used by some SoCs to return to BROM.
Port this to ARM926EJ-S start code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.
The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is some code that tries to "reset" the SCTLR_ELx register early in
the boot process. The idea seems to be to guarantee some sane settings
that U-Boot actually relies on, for instance running in little-endian
mode, with the MMU off initially.
However the current code has multiple problems:
- For a start, no platform or config defines the symbol that would
enable that code.
- The code itself really only works if the bits that it tries to clear
are already cleared:
- If we run in big-endian mode initially, any previous loads would have
been wrong already. That applies to the (optional) relocation code,
but more prominently to the mask that it uses to clear those bits:
"ldr x1, =0xfdfffffa" looks innocent, but actually involves a memory
access to the literal pool, using the current endianness.
- If we run with the MMU enabled, we are probably doomed already. We
*could* hope that we are running with an identity mapping, but would
need to do some cache maintenance to avoid losing dirty cache lines.
- The idea of doing a read-modify-write of SCTLR is somewhat
questionable to begin with, because as the owner of the current
exception level we should initialise all bits of this register with a
certain fixed value.
- The code is unnecessarily complicated, and the function name is
misspelled.
While those problems *could* admittedly be fixed, the point that is does
not seem to be used at all at the moment tells me we should just remove
this code, and be it to not give a bad example.
If people care, I could introduce some proper SCTLR initialisation code.
We are about to work this out for the boot-wrapper[1] as we speak, but
apparently we got away without doing this in U-Boot ever since, so it
might not be worth the potential trouble.
[1] https://lore.kernel.org/linux-arm-kernel/20220114105653.3003399-7-mark.rutland@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Setting LINUX_KERNEL_IMAGE_HEADER=y attempts to include an ARM64 Linux
kernel image header at the start of both U-Boot proper and SPL binaries.
However, some definitions that the image header uses are not included by
the SPL linker script, resulting in a build error. Include them the way
they are included in U-Boot proper's linker script to fix the error.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Apple's ARMv8 cores don't implement EL3 and therefore don't
provide a PSCI implementation. So don't attempt to use
PSCI to reset on machines using Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
