STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
Add stm32746g-eval_defconfig for stm32746g evaluation board to
build U-Boot proper.
Full board description can be found here :
https://www.st.com/en/evaluation-tools/stm32746g-eval.html
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace CONFIG_SUPPORT_SPL by CONFIG_SPL_BUILD to allow
dram_init() execution when using none SPL defconfig
(stm32f746-disco_defconfig).
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The current stm32f769-disco_defconfig file supports SPL, rename it to
stm32f769-disco_spl_defconfig to reflect the supported configuration.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The current stm32f746-disco_defconfig file supports SPL, rename it to
stm32f746-disco_spl_defconfig to reflect the supported configuration.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Always consider USB cable is connected when USB boot device is detected.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add missing \n at the end of the error trace
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
On this platform DM_I2C and SPL_DM_I2C enabled.
Remove legacy code.
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove Masami Hiramatsu from MAINTAINERS since he will leave
Linaro and his email will be not available anymore.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, we need to stop using board_network_enable() and instead
use the DM registered MDIO device to configure switch in
last_stage_init().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables the Kconfig symbols needed for full ethernet support
on the NIC23. Additionally board specific setup is done, mostly GPIOs
related to SFP / GPIO configuration. With this, ethernet can be used on
this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
Using ethernet-mac-nexus@11800e2000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.247
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
9.7 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <sr@denx.de>
To quote the author:
U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.
This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.
Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.
Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
MPP55 is used as a reset connected to the L3 switch chip. This doesn't
matter for u-boot as it doesn't use the L3 switch but it is useful to
be able to toggle the switch in/out of reset for the OS.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
PCIe Mini CEM 2.1 spec added support for USB3.0 mode on MiniPCIe cards.
USB3.0 and PCIe share same pins and only one function can be active at the
same time. PCIe Mini CEM 2.1 spec says that determining function is
platform specific and spec does not define any dedicated pin which could
say if card is USB3.0-based or PCIe-based.
Implement this platform specific decision (USB3.0 vs PCIe) for WWAN
MiniPCIe slot on Turris Omnia via U-Boot env variable "omnia_wwan_slot",
similarly like is implemented forced mode for MiniPCIe/mSATA slot via
"omnia_msata_slot" env variable. Value "usb3" for "omnia_wwan_slot" would
mean to set USB3.0 mode and value "pcie" original PCIe mode.
A385 SoC on Turris Omnia has configurable fifth SerDes line (exported to
MiniPCIe WWAN slot with SIM card) either to USB3.0 or PCIe functionality,
so implementation of this new PCIe Mini CEM 2.1 feature is simple, by just
configuring SerDes to USB 3.0 mode.
Other twos MiniPCIe slots on Turris Omnia do not have this new
functionality as their SerDes lines cannot be switched to USB3.0
functionality.
Note that A385 SoC does not have too many USB3.0 blocks, so activating
USB3.0 in MiniPCIe cause that one external USB3.0 USB-A port would loose
USB3.0 functionality and would be downgraded just to USB2.0.
By default this MiniPCIe WWAN slot is in PCIe mode, like before.
To set this MiniPCIe WWAN slot to USB3.0 mode, call U-Boot commands:
=> setenv omnia_wwan_slot usb3
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
Show error message when DT file does not contain sata or pcie node which
should be explicitly disabled. This can happen when U-Boot code for finding
those nodes is incomplete or when those DT nodes are in different
unexpected location. In any case it is needed to know if DT not was not
explicitly disabled as it could mean that combo slots where setup
incorrectly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Move code for disabling sata and pcie DT nodes to own functions, so this
code can be called from other places in follow up patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Some PCIe-based MiniPCIe cards are broken and they do not ground PIN 43
which is required by PCIe mini CEM specs. Such broken cards are incorrectly
detected as mSATA cards because SATA specs requires that PIN 43 on mSATA
cards has to be disconnected.
PIN 43 on Turris Omnia is used only for MiniPCIe/mSATA card detection by
software in U-Boot SPL. Allow to override that U-Boot SPL detection by a
new "omnia_msata_slot" env variable (to value "pcie" or "sata") so broken
MiniPCIe cards can be used in combo mSATA/MiniPCIe slot too.
As configuration of PCIe vs SATA functionality is done in U-Boot SPL,
it is required to change env variable in permanent storage and reset the
board to take effect.
To force PCIe mode for broken MiniPCIe cards, call U-Boot commands:
=> setenv omnia_msata_slot pcie
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
By default use primary serdes map with PCIe function in combined
miniPCIe/mSATA slot. When SATA is detected change serdes map variable at
runtime.
Signed-off-by: Pali Rohár <pali@kernel.org>
BootROM maps SPI Flash to fixed address 0xD4000000 and this mapping is
active also when BootROM is executing binary kwbimage headers, which
includes also U-Boot SPL.
Therefore no initialization code is required to access SPI Flags from
U-Boot SPL. In proper U-Boot it is remapped to other location.
So in mvebu implementation of env_sf_get_env_addr() function returns
0xD4000000 when running in SPL and NULL when in proper U-Boot.
This change would allow to use U-Boot ENV in U-Boot SPL. Normally it is not
possible to read ENV because it is too big and U-Boot SPL does not have
such big malloc() pool to real all ENV variables.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This function is empty, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Manish Tomar's email bounces. Remove it, and reassign the config he was
maintaining to the primary maintainer for the board.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Whole section about USB/eLBC configuration seems to be P1020 specific. So
add ifdefs to not compile it on other platforms (e.g. P2020).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like for first 1G SDRAM map, do not enable Caching-inhibited nor Guarded
attribute for second 1G SDRAM mapping. Whole 2G SDRAM should use caches and
also allow speculative loading (by not setting Guarded attribute).
Also enable Memory Coherency attribute for second 1G SDRAM map. In commit
316f0d0f8f ("powerpc: mpc85xx: Fix static TLB table for SDRAM") it was
enabled for all SDRAM maps on all other boards, just missed this one case.
As a last thing, first 1G SDRAM map has wrong comment, so adjust it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When MPC85xx_PMUXCR_SDHC_WP is set then SDHC controller automatically makes
inserted SD card readonly if GPIO[9] is active.
In some design GPIO[9] pin does not have to be connected to SD card
write-protect pin and can be used as GPIO.
So do not set MPC85xx_PMUXCR_SDHC_WP bit when GPIO[9] is not used for
SDHC_WP functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like in all other checks in checkboard() function, do not hang on error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
