The pci_ftpci_init() function is implemented
in 'drivers/pci/pci_ftpci100.c' however it is
always called by external code.
Add function declaration into ftpci100.h to
make it visible for external code.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Add a const keyword to the sect_buf argument of
ide_write_data to fix the following warning:
cmd_ide.c: In function '__ide_output_data':
cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type
/devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *'
Also modify the driver-model documentation to
match with the new prototype.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Faraday FTI2C010 is a multi-function I2C controller
which supports both master and slave mode.
This patch simplily implements the master mode only.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Heiko Schocher <hs@denx.de>
This patch adds support for Vybrid VF610 platform.
There are some differences between i.MX6 and Vybrid for I2C controller.
(1) The registers' offset are different.
(2) The I2C clock divider values are different.
(3) In I2C control register, the enable/disable/reset bit is inverted for Vybrid comparing to i.MX6.
(4) In I2C status register, the interrupt flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
(5) In I2C status register, the arbitration lost flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
Signed-off-by: Alison Wang <b18965@freescale.com>
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Rather than using a variable in various places, add a single function,
tegra_i2c_get_bus(), which returns a pointer to information about a
bus.
This will make it easier to move to the new i2c framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.
Set the SUPPORTED_1000baseX_Half flag instead.
Acked-by: Charles Coldwell <coldwell@gmail.com>
Reviewed-By: Sascha Silbe <t-uboot@infra-silbe.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.
Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Atmel TPM devices with two wire interface.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
if alen is 0: no longer start a write cycle before reading data.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The driver triggered a BUG() in nand_base.c:3214/nand_scan_tail()
because the ecc.strength was not set in NAND_ECC_HW_SYNDROME ECC
mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.
This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
The DFU's state machine original implementation author and copyright were
missing.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case
Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Code for checking "splashpos" environment variable is
duplicated in drivers, move it to the common function.
Call this function also in the bmp display command to
consider "splashpos" settings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Add support for disabling battery charging with ctrl+C keyboard
combination pressed.
Moreover the battery update is done more frequently.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For the first eMMC read of data for upload, use the "large" dfu_buf (now
configurable) instead of usb request buffer allocated at composite layer
(which is 4KiB) [*].
For eMMC the whole file is read, which usually is larger than the buffer [*]
provided with usb request.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
In the following commit:
"dfu: Support larger than memory transfers."
SHA1: ea2453d56b
The ext4{read|write} command formatting has been changed. It removed
a write mandatory [sizebytes] parameter.
It extents DFU_FS_EXT4 case at mmc_file_op to provide mandatory
parameter for DFU write.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch fix the omap access to the transceiver
configuration registers using the ulpi bus. As reported by
the documentation the bit31 is used only to check if the
transaction is done or still running and the reading and
writing operation have different offset and have different
values. What we need to do at the end of a transaction is
leave the bus in done state. Anyway an error using the ulpi
omap register is not recoverable so any error give out the
usage of this interface.
Tested on a custom OMAP5430 board with a TUSB1210 ULPI PHY
on USBB1.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Create splash.c/h to put the function and any future common splash
screen code in.
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch change 'data_to_send' array to static to avoid
unaligned access exeption on some platforms (ex Trats2).
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Anatolij Gustschin <agust@denx.de>
This trivial patch adds the definition of the vid/pid for the Ver C1 of the
USB Ethernet adapter D-Link DUB-E100.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Marek Vasut <marex@denx.de>
This subtle change fix problem with too small amount of allocated
memory to store DFU function pointers.
One needs to allocate extra space for sentinel NULL pointer in this array
of function pointers.
With the previous code, the NULL value overwrites malloc internal data
and afterwards free(f_dfu->function) crashes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
- set in to_dfu_mode() f_dfu->dfu_state = DFU_STATE_dfuIDLE
as after every to_dfu_mode call this is done, so move
this into to_dfu_mode
- switch in dfu_bind() into dfu mode:
This fixes wrong "dfu-util -l" output, when calling
"dfu-util -l" after a board reset, without doing a
download before. See also discussion here:
http://lists.denx.de/pipermail/u-boot/2013-June/157272.html
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch memcpy is used instead of an assignment to
avoid unaligned access execption on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch use get|put_unaligned_le16 to access structure data
to avoid data abort on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marex@denx.de>
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable through environment variable "dfu_bufsiz".
Defaut value is configurable through CONFIG_SYS_DFU_DATA_BUF_SIZE
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
Currently we have the following on boot:
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
DRAM: 128 MiB
MMC: MXS MMC: 0
Video: MXSFB: 'videomode' variable not set!In: serial
Break the line of the warning message in order to have a better reading format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
The spi clock divisor is of the form x * (2**y), or x << y, where x is
1 to 16, and y is 0 to 15. Note the similarity with floating point numbers.
Convert the desired divisor to the smallest number which is >= desired divisor,
and can be represented in this form. The previous algorithm chose a divisor
which could be almost twice as large as needed.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Fix two issues with the calculation of pre_div and post_div:
1. pre_div: While the calculation of pre_div looks correct, to set the
CONREG[15-12] bits pre_div needs to be decremented by 1:
The i.MX 6Dual/6Quad Applications Processor Reference Manual (IMX6DQRM
Rev. 0, 11/2012) states:
CONREG[15-12]: PRE_DIVIDER
0000 Divide by 1
0001 Divide by 2
0010 Divide by 3
...
1101 Divide by 14
1110 Divide by 15
1111 Divide by 16
I.e. if we want to divide by 2, we have to write 1 to CONREG[15-12].
2. In case the post divider becomes necessary, pre_div will be divided by
16. So set pre_div to 16, too. And not 15.
Both issues above are tested using the following examples:
clk_src = 60000000 (60MHz, default i.MX6 ECSPI clock)
a) max_hz == 23000000 (23MHz, max i.MX6 ECSPI read clock)
-> pre_div = 3 (divide by 3 => CONREG[15-12] == 2)
-> post_div = 0 (divide by 1 => CONREG[11- 8] == 0)
=> 60MHz / 3 = 20MHz SPI clock
b) max_hz == 2000000 (2MHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 1 (divide by 2 => CONREG[11- 8] == 1)
=> 60MHz / 32 = 1.875MHz SPI clock
c) max_hz == 1000000 (1MHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 2 (divide by 4 => CONREG[11- 8] == 2)
=> 60MHz / 64 = 937.5kHz SPI clock
d) max_hz == 500000 (500kHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 3 (divide by 8 => CONREG[11- 8] == 3)
=> 60MHz / 128 = 468.75kHz SPI clock
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
This patch adds the driver for keyboard that's controlled by ChromeOS EC.
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds LPC support for carrying out the cros_ec protocol.
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds SPI support for carrying out the cros_ec protocol.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds I2C support for carrying out the cros_ec protocol.
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds the cros_ec driver that implements the protocol for
communicating with Google's ChromeOS embedded controller.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Current code had writel arguments the wrong way around, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
add atheros ar803x phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
add natsemi dp83630 phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.
Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
commit 39695029bc15041c809df3db4ba19bd729c447fa
Author: Charles Coldwell <coldwell@ll.mit.edu>
Date: Tue Feb 19 08:27:33 2013 -0500
Changes to support the Xilinx 1000BASE-X phy (GTX/MGT)
Signed-off-by: Charles Coldwell <coldwell@ll.mit.edu>
Add support for Micrel PHY KSZ9031 in phylib,
including small rework for KSZ9021 to avoid
code duplication
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Joe Herschberger <joe.hershberger@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.
Call an arch specific function to take control of specific mdio lines at
runtime.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Marvell Dove also uses mvgbe as ethernet driver, therefore add support
for Dove to reuse the current driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
before writing the received buffer to nand, erase the nand
sectors. If not doing this, nand write fails. See for
more info here:
http://lists.denx.de/pipermail/u-boot/2013-June/156361.html
Using the nand erase option "spread", maybe overwrite
blocks on, for example another mtd partition, if the
erasing range contains bad blocks.
So a limit option is added to nand_erase_opts()
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds FDT support to the serial s5p driver.
At present disabling the serial console (from the device tree) crashes
U-Boot. Add checks for this case, so that execution can continue without
a serial console.
It also enables the serial_s5p driver recognize the silent_console option.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch updates the function board_i2c_init() to add support for both
FDT and non-FDT for I2C, and initialise the I2C channels.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move common flash write code into spi_flash_write_common().
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flag status register polling is required for micron 512Mb flash
devices onwards, for performing erase/program operations.
Like polling for WIP(Write-In-Progress) bit in read status register,
spi_flash_cmd_wait_ready will poll for PEC(Program-Erase-Control)
bit in flag status register.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no other call other than spi_flash_cmd_wait_ready(),
hence removed spi_flash_cmd_poll_bit and use the poll status code
spi_flash_cmd_wait_ready() itself.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the existing spi_flash_addr() for 3-byte addressing
cmd filling in write call.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Defined bank addr code on CONFIG_SPI_FLASH_BAR macro, to reduce the
size for existing boards which has < 16Mbytes SPI flashes.
It's upto user which has provision to use the bank addr code for
flashes which has > 16Mbytes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch updated the spi_flash read func to support all
sizes of flashes using bank reg addr facility.
The same support has been added in below patch for erase/write
spi_flash functions:
"sf: Support all sizes of flashes using bank addr reg facility"
(sha1: c956f600cbb0943d0afe1004cdb503f4fcd8f415)
With these new updates on sf framework, the flashes which has < 16MB
are not effected as per as performance is concern and but the
u-boot.bin size incrased ~460 bytes.
sf update(for first 16MBytes), Changes before:
U-Boot> sf update 0x1000000 0x0 0x1000000
- N25Q256
16777216 bytes written, 0 bytes skipped in 199.72s, speed 86480 B/s
- W25Q128BV
16777216 bytes written, 0 bytes skipped in 351.739s, speed 48913 B/s
- S25FL256S_64K
16777216 bytes written, 0 bytes skipped in 65.659s, speed 262144 B/s
sf update(for first 16MBytes), Changes before:
U-Boot> sf update 0x1000000 0x0 0x1000000
- N25Q256
16777216 bytes written, 0 bytes skipped in 198.953s, speed 86480 B/s
- W25Q128BV
16777216 bytes written, 0 bytes skipped in 350.90s, speed 49200 B/s
- S25FL256S_64K
16777216 bytes written, 0 bytes skipped in 66.521s, speed 262144 B/s
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Updated the spi_flash framework to handle all sizes of flashes
using bank/extd addr reg facility
The current implementation in spi_flash supports 3-byte address mode
due to this up to 16Mbytes amount of flash is able to access for those
flashes which has an actual size of > 16MB.
As most of the flashes introduces a bank/extd address registers
for accessing the flashes in 16Mbytes of banks if the flash size
is > 16Mbytes, this new scheme will add the bank selection feature
for performing write/erase operations on all flashes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Read the flash bank addr register to get the state of bank in
a perticular flash. and also bank write happens only when there is
a change in bank selection from user.
bank read only valid for flashes which has > 16Mbytes those are
opearted in 3-byte addr mode, each bank occupies 16Mytes.
Suppose if the flash has 64Mbytes size consists of 4 banks like
bank0, bank1, bank2 and bank3.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bank/Extended addr commands are specific to particular
flash vendor so discover them based on the idocode0.
Assign the discovered bank commands to spi_flash members
so-that the bank read/write will use their specific operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch provides support to program a flash bank address
register.
extended/bank address register contains an information to access
the 4th byte addressing in 3-byte address mode.
reff' the spec for more details about bank addr register
in Page-63, Table 8.16
http://www.spansion.com/Support/Datasheets/S25FL128S_256S_00.pdf
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change slightly improves readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This change slightly improves readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Use the exact names for W25Q 0x40XX ID's flash parts, as the same
sizes of flashes comes with different ID's. so-that the distinguishes
becomes easy with this change.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Corrected the name of S25FL128S 64K sector part SPI flash,
S25FL128S supported has been added in below commit
"sf: spansion: Add support for S25FL128S"
(sha1: 1bfb9f156a)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch fixes a bug introduced while adding DT support
to Exynos FIMD driver:
commit c23f3157d6
Author: Ajay Kumar <ajaykumar.rs@samsung.com>
Date: Thu Feb 21 23:53:01 2013 +0000
video: exynos_fb: add DT support for FIMD driver
Even though this part of code was missing, things were working
fine on Exynos5250 because, samsung_get_base_fimd() used
to give the correct base address for Exynos5250 FIMD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit dfe64e2c89
Author: Sergey Lapin <slapin@ossfans.org>
Date: Mon Jan 14 03:46:50 2013 +0000
mtd: resync with Linux-3.7.1
changed the initialization of BBT options. Fix drivers
jz4740 and s3c2410 which have not been updated yet and
cause compile errors.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Commit dfe64e2c89:
mtd: resync with Linux-3.7.1
broke the docg4 driver. Specifically:
- some of the prototypes of the ecc methods changed
- the NAND_NO_AUTOINCR flag was removed
- the ecc.strength element was added.
This patch fixes these. Tested on the docg4 on my palmtre680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch corrected the nr_blocks used for W25Q32DW SPI flash.
nr_blcoks are incorrectly assigned on below patch
"sf: winbond: add W25Q32DW"
(sha1: 772ba15474)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support for Winbond W25Q80BW SPI flash.
This patch corrected the flash name, nr_blocks and
also commit message header from below patch.
"sf: winbond: add W25Q32"
(sha1: c969abc470)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
As the per the ID tabl the flash is under Uniform 64-kB sector
architecture, hence updated with proper name.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
It's done in spi_alloc_slave(), thus remove the redundant code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch implements the mux_addr bit fields defined in tmu_control
register (used for debugging purpose)
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch does the folowing
1. change the data types for unsigned int variable to unsigned
2. change the tmu_base type to struct exynos5_tmu_reg *
3. Add timer functionality for get_cur_temp()
4. error handling in the get_tmu_fdt_values()
5. Add check for curr_temp reading
6. some cosmotic changes.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Without this, second usb_composite_register() call fails always
with -EINVAL.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Commit 8f62ca6 "usb: ehci: Support interrupt transfers via periodic list"
didn't include any cache management in the new interrupt transfer path.
It also added an extra write to or_asynclistaddr in usb_lowlevel_init(),
without having flushed out the data there.
Add the missing cache management calls, so that the code works again.
This allows the USB keyboard on Tegra's Seaboard/Springbank boards to
work.
Cc: Patrick Georgi <patrick@georgi-clan.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Faraday FOTG210 is an OTG chip which could operate
as either an EHCI Host or a USB Device at a time.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
There is at least one non-EHCI compliant controller (i.e. Faraday EHCI)
not only leave RESERVED and CONFIGFLAG registers un-implemented
but also has their address spaces removed.
As an result, the PORTSC register of Faraday EHCI always
starts from 0x30 instead of 0x44 in standard EHCI.
So that we'll need a weak-aliased function for abstraction.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
1. The 'index' of ehci_submit_root() is not always > 0.
e.g.
While it gets invoked from usb_get_descriptor(),
the 'index' is always a '0'. (See ch.9 of USB2.0)
2. The PORTSC register is not always required, and thus it
should only report a port error when necessary.
It would cause a port scan failure if the ehci_submit_root()
always gets terminated by a port error.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
Use get_unaligned() while fetching wMaxPacketSize to avoid
voilating any alignment rules.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Dalek <luk0104@gmail.com>
Cc: Marek Vasut <marex@denx.de>
The ASIX driver calls a basic_init() function during get_info(), so that
not all initialization tasks need to be redone on every init().
Unfortunately, the most important one is still triggered too often: the
driver does a full port and MII reset on every asix_init(), requiring up
to several seconds to reestablish the link.
This patch confines that software reset into the asix_basic_init()
function so that it will only be executed once. This saves about a
second of boot time on systems using BOOTP.
Note: this patch was previously submitted many moons ago as:
usb: usbeth: asix: Do a fast init if link already established
That patch seens to have been lost or forgotten, so this is a rebased
version. It is tested on snow with a Asix USB dongle (Cisco).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This commit broke USB2 on link (Chromebook Pixel):
020bbcb usb: hub: Power-cycle on root-hub ports
However the root cause seems to be a missing mask and missing 'break'
in ehci-hcd.c. This patch fixes both.
On link, 'usb start' with a USB keyboard and memory stick inserted now
finds both. The keyboard works as expected. Also ext2ls shows a directory
listing from the memory stick.
Signed-off-by: Simon Glass <sjg@chromium.org>
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
(4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
OMAPs and derivatives as well. The only anticipated exception would
be the OMAP2420, which shall require driver modification.
- Rewritten i2c_read to operate correctly with all types of chips
(old function could not read consistent data from some I2C slaves).
- Optimised i2c_write.
- New i2c_probe, performs write access vs read. The old probe could
hang the system under certain conditions (e.g. unconfigured pads).
- The read/write/probe functions try to identify unconfigured bus.
- Status functions now read irqstatus_raw as per TRM guidelines
(except for OMAP243X and OMAP34XX).
- Driver now supports up to I2C5 (OMAP5).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Heiko Schocher <hs@denx.de>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
Add some useful functions, and the corresponding definitions.
Add support for powering on the dra7xx_evm SD/MMC LDO
(courtesy Lokesh Vutla <lokeshvutla@ti.com>).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.
Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.
Also add the new option into the configuration
files of the boards which needs that.
Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:
powerpc:
--------------------- SUMMARY ----------------------------
Boards compiled: 641
Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
----------------------------------------------------------
Note: the warnings for ELPPC and MPC8323ERDB are present even
without the actual patch.
x86:
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------
arm:
--------------------- SUMMARY ----------------------------
Boards compiled: 311
----------------------------------------------------------
nds32:
--------------------- SUMMARY ----------------------------
Boards compiled: 3
----------------------------------------------------------
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
[trini: Applied v1 of the series rather than v2, this commit is the
delta from v1 to v2]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
We know the exact property names that the code wants to process. Look
these up directly with fdt_get_property(), rather than iterating over
all properties within the node, and checking each property's name, in
a convoluted fashion, against the expected name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Initialized character arrays on the stack can cause gcc to emit code that
performs unaligned accessess. Make the data static to avoid this.
Note that the unaligned accesses are made when copying data to prefix[] on
the stack from .rodata. By making the data static, the copy is completely
avoided. All explicitly written code treats the data as u8[], so will never
cause any unaligned accesses.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds lpuart support for Vybrid VF610 platform.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
This patch adds FEC support for Vybrid VF610 platform.
In function fec_open(), RCR register is only set as RGMII mode. But RCR
register should be set as RMII mode for VF610 platform.
This configuration is already done in fec_reg_setup(), so this piece of
code could just leave untouched the FEC_RCNTRL_RGMII / FEC_RCNTRL_RMII /
FEC_RCNTRL_MII_MODE bits.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch does a similar code reogranzation from
http://patchwork.ozlabs.org/patch/132179/
which is based on an old version of code (fdt support and bus selection
still not in). It merges this tidy-up on top of the recent code. It does
not make any logical change.
tpm.c implements the interface defined in tpm.h based on underlying
LPC or I2C TPM driver. tpm.c and the underlying driver communicate
throught tpm_private.h.
Note: Merging the LPC driver with tpm.c is left to future patches.
Change-Id: Ie1384f5f9e3935d3bc9a44adf8de80c5a70a5f2b
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Infineon's new SLB 9645 TT 1.2 I2C TPMs,
which supports clockstretching, combined reads and a bus speed of
up to 400khz. The device also has a new device id.
This is based on the kernel patch provided by Infineon :
https://gerrit.chromium.org/gerrit/42332
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Tom Wai-Hong Tam <waihong@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
The new name is more aligned with Linux kernel's naming of TPM driver.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Wai-Hong Tam <waihong@chromium.org>
This patch adds a print messages while using 'sf read' and
'sf write' commands to make sure that how many bytes read/written
from/into flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds a print messages while using 'sf erase' command
to make sure that how many bytes erased in flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Tom Rini <trini@ti.com>
Missing return after memcpy is done for memory-mapped SPI flashes,
hence added retun 0 after memcpy done.
The return is missing in below patch
"sf: Enable FDT-based configuration and memory mapping"
(sha1: bb8215f437)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Support interfaces with a preamble before each received message.
We handle this when the client has requested a SPI_XFER_END, meaning
that we must close of the transaction. In this case we read until we
see the preamble (or a timeout occurs), skipping all data before and
including the preamble. The client will receive only data bytes after
the preamble.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for Winbond's W25PXX SPI flash.
These devices is used on Faraday A369 evaluation board.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
CC: Tom Rini <trini@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for Winbond W25Q256 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This is a S25FL064A successor. It supports up to 104MHz bus
speed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
SPANSION recommend S25FL128S supersedes S25FL129P, and the two flash
memory have the same device ID and Memory architecture. So they can
use the same config parameters.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
TN80xx has same PHY ID as TN2020, but it needs different setting to register
30.93 which used to select line, so we read register 30.32 which has
bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2,
for TN80xx we will get 5 or 4.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When base address given was out of valid flash address ranges,
flash_get_info() function returned the pointer to the last
element of flash_info[i] array.
This patch changes this function to return NULL pointer
in such a case, which is more correct behaviour.
The function flash_protect_default() calls flash_protect()
immediately after flash_get_info() invocation.
With this correction, flash_protect() function would be
able to return soon, for NULL flash_info.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Linux Kernel Documentation/CodingStyle says:
Do not add a space after unary operators such as &, *, ...
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Packed structure cfi_qry contains unaligned 16- and 32-bits members,
accessing which causes problems when cfi_flash driver is compiled with
-munaligned-access option: flash initialization hangs, probably
due to data error.
Since the structure is supposed to replicate the actual data layout
in CFI Flash chips, the alignment issue can't be fixed in the structure.
So, unaligned fields need using of explicit unaligned access macros.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Stefan Roese <sr@denx.de>
When a all 0xFF buffer is passed to drop_ffs, the no-0xFF check loop
will loop forever.
After the fix, If ssize_t i = -1 and size_t l = i + 1, the value of l
will still be 0 as expected.
Signed-off-by: Tao Hou <hotforest@gmail.com>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: Scott Wood <scottwood@freescale.com>
When writelen is mtd->writesize - 1, it is still a partial page write
Signed-off-by: Tao Hou <hotforest@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
This avoids needing a separate U-Boot config when some revisions
of a board have small-page NAND and other revisions have large-page
NAND (except for NAND SPL targets).
CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and
it gets in the way of this change.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch enables the uart tx/rx fifo. Now that fifo is enabled,
the uart read/write functions are modfied to check the UFSTAT register
for fifo status instead of UTRSTAT (as required with fifo's enabled).
Tested by booting linux kernel. Before enabling tx/rx fifo
"Uncompressing linux" message is garbled and after enabling it is proper.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds driver for the gigabyte devices
GD25LQ and GD25Q64B required for Snow Board.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently the mxsfb driver takes the display timings from the 'videomode'
environment variable.
Provide an example on how to set 'videomode' for using splash screen on
mx23evk and mx28vk boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Marek Vasut <marex@denx.de>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
