The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.
It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.
Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Add code to get the FPGA type for Altera's SoCFPGA family of FPGA. The code
uses the scan manager to send jtag pulses that will return the FPGA ID.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Factor out the code which sends JTAG instruction followed by data
into separate function to tidy the code up a little.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Clean up the horrible macros present in the scan_manager.h . Firstly,
the function scan_mgr_io_scan_chain_prg() is static, yet all the macros
are used only within it, thus there is no point in having them in the
header file. Moreover, the macros are just making the code much less
readable, so remove them instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce generic function for accessing the JTAG scan chains in the
SCC manager. Make use of this function throughout the SCC manager to
replace the ad-hoc writes to registers and make the code less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Rework this function so it's clear that it is only polling for certain
bits to be cleared. Add kerneldoc. Fix it's return value to be either
0 on success and -ETIMEDOUT on error and propagate this through the
scan manager code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Zap non-existent functions and place function prototypes at the
beginning of the header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.
The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that the SPL structure is organised such that it matches the
U-Boot's SPL design, it is possible to use the option of relocating
GD to RAM. And since we have GD in RAM, move malloc area to RAM as
well. We point the malloc base pointer 1 MiB past U-Boot's load
address. We use simple malloc for SPL because it is 3kiB smaller
in terms of code size than regular malloc which was used thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Reset the GMAC ethernets based on the "resets" OF node instead of ad-hoc
hardcoded values in the U-Boot code. Since we don't have a proper reset
framework in place yet, we have to do this slightly ad-hoc parsing of the
OF tree instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
setenv an environment variable called "bootmode" , which contains the
board boot mode. This can be in turn used in scripts to determine from
where to load kernel and such.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for printing from which device the SoCFPGA board booted.
This decodes the BSEL settings and prints it in human readable form.
Signed-off-by: Marek Vasut <marex@denx.de>
Write necessary magic value into the Warm Boot from ON-Chip RAM
group Enable register to enable Warm reset support. Instead of
doing this in the reset_cpu() function, we do it in arch early
init to avoid breaking old kernel code which expects this magic
value to be already written into this register.
This magic is originally excavated from common/spl/spl.c in the
u-boot port from altera, where this value was written just before
the SPL jumped to actual U-Boot in the RAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework spl_boot_device() such that it reads the BSEL settings from
system manager and decides from where to load U-Boot based on this
information.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from QSPI NOR.
Enable support for booting from QSPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from RAW
SD/MMC card as well as for ext4/vfat filesystems. Enable support
for booting from SD/MMC card, but don't enable the filesystem
support just yet to retain compatibility with old SoCFPGA card
format.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove the custom SPL linker script, use the generic one instead.
The custom script doesn't bring in anything new and is only burden
to maintain.
Signed-off-by: Marek Vasut <marex@denx.de>
The code in spl_board_init() should have been in board_init_f()
from the beginning, since it is code which configures system and
then starts DRAM. Thus, it cannot be in spl_board_init(), which
is called from board_init_r() , which already expects a working
DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Make sure that all the peripherals are correctly reset and then
brought out of reset in the SPL. Not going through proper reset
cycle might leave the IP blocks in inconsistent state.
Signed-off-by: Marek Vasut <marex@denx.de>
Configure the ARM SCU and NIC301 very early. The ARM SCU SNSAC register
must be configured, so we can access all peripherals. The NIC-301 must
be configured so that the BootROM is not mapped into the SDRAM address
space.
Signed-off-by: Marek Vasut <marex@denx.de>
Synchronise the SPL behavior with the original Altera code and
toggle the Warm Reset Config I/O bit accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement new accessor, sysmgr_get_pinmux_table(), used to obtain pinmux
table and it's size from the QTS-generated pinmux_config.c. The target
here is again to get rid of poluting global namespace by including the
pinmux_config.h into it.
Furthermore, the pinmux_config.h declares some CONFIG_HPS_* macros,
which are explicitly useless to us in U-Boot. Instead, U-Boot does
use DT to detect exactly these configuration options. This patch
makes sure that while this QTS-generated file can stay in the tree,
these obscure macros do not ooze into the namespace anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework sysmgr_enable_warmrstcfgio() into sysmgr_config_warmrstcfgio(),
which allows both enabling and disabling the warm reset config I/O
functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce accessor iocsr_get_config_table() for retrieving IOCSR config
tables. This patch is again trimming down the namespace polution.
The IOCSR config tables are used only by scan manager, they are generated
by qts and are board specific. Before this patch, the approach to use
these tables in scan manager was to define an extern variable to silence
the compiler and compile board-specific iocsr_config.c into U-Boot which
defined those extern variables. Furthermore, since these are tables and
the scan manager needs to know the size of those tables, iocsr_config.h
is included build-wide.
This patch wraps all this into a single accessor which takes the scan
chain ID and returns pointer to the table and it's size. All this is
wrapped in wrap_iocsr_config.c board-specific file. The file includes
the iocsr_config.c (!) to access the original tables and transitively
iocsr_config.h . It is thus no longer necessary to include iocsr_config.h
build-wide and the namespace polution is trimmed some more.
Signed-off-by: Marek Vasut <marex@denx.de>
It is sufficient to pass in the scan chain ID into the function to determine
the remaining two parameters, so drop those params and determine them locally
in the function. The big-ish switch in the function is temporary and will be
replaced by a proper function call in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is never used outside of scan_manager.c , so make it static.
Zap the prototype in scan_manager.h and move the documentation above the
function. Make the documentation kerneldoc compliant.
Signed-off-by: Marek Vasut <marex@denx.de>
Extract the clock configuration horribleness caused by pll_config.h in
the following manner.
First of all, introduce a few new accessors which return values of
various clocks used in clock_manager.c and use them in clock_manager.c .
These accessors replace those few macros which came from pll_config.h
originally. Also introduce an accessor which returns the struct cm_config
default configuration for the clock manager used in SPL.
The accessors are implemented in a board-specific wrap_pll_config.c
file, whose sole purpose is to include the qts-generated pll_config.h
and provide only the necessary values to the clock manager.
The purpose of this design is to limit the scope of inclusion for the
pll_config.h , which thus far was included build-wide and poluted the
namespace. With this change, the inclusion is limited to just the new
wrap_pll_config.c file, which in turn provides three simple functions
for the clock_manager.c to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Add socfpga_per_reset_all() function to reset all peripherals
but the L4 watchdog. This is needed in the SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
The current bridge reset code, which de-asserted the bridge reset,
was activelly polling whether the FPGA is programmed and ready and
in case it was (!), the code called hang(). This makes no sense at
all. Repair it such that the code instead checks whether the FPGA
is programmed, but without any polling involved, and only if it is
programmed, it de-asserts the reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Replace all those ad-hoc reset functions, which were all copies
of the same invocation of clrbits_le32() anyway, with one single
unified function, socfpga_per_reset(), with necessary parameters.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement function socfpga_per_reset(), which allows asserting or
de-asserting reset of each reset manager peripheral in a unified
manner. Use this function throughout reset manager.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement macro SOCFPGA_RESET(name), which produces an abstract
reset number. Implement macros which allow extracting the reset
offset in permodrstN register and which permodrstN register the
reset is located in from this abstract reset number. Use these
macros throughout the reset manager.
Signed-off-by: Marek Vasut <marex@denx.de>
Move the structure prototype from sdram.h header file into sdram.c
source file, since it is used only there and for local purpose only.
There is no point in having it global.
While at this move, fix the data types in the structure from uintNN_t
to uNN and fix the coding style a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch enables the SDRAM controller that is used on Altera's SoCFPGA
family. This patch configures the SDRAM controller based on a configuration
file that is generated from the Quartus tool, sdram_config.h.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add alias for the SD/MMC controller, so it can be located by U-Boot OF support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The SPI aliases are completely wrong. First, they point to non-existing
/spi@.* nodes instead of the correct /soc/spi@.* nodes. Second, the use
ad-hoc string instead of a handle. Furthermore, they are copied multiple
times in each board DTS.
So fix it such that we move these into socfpga.dtsi and make them use
the usual handles.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O
board. The combination contains SoC, DRAM, eMMC, SD card slot,
HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
a GPIO expansion header, and an analog audio jack.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM,
eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various
expansion modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Additionally, ARM64 devices typically run a secure monitor in EL3 and
U-Boot in EL2, and set up some secure RAM carve-outs to contain the EL3
code and data. These carve-outs are located at the top of 32-bit address
space. Restrict U-Boot's RAM usage to well below the location of those
carve-outs. Ideally, we would the secure monitor would inform U-Boot of
exactly which RAM it could use at run-time. However, I'm not sure how to
do that at present (and even if such a mechanism does exist, it would
likely not be generic across all forms of secure monitor).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present lower case is used for the regulator names in the device tree.
The kernel uses upper case and U-Boot will require this also since it will
move to a case-sensitive name check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
While the AP can access the main PMIC on snow, it must coordinate with the
EC which also wants access. Drop the old definition, which can in principle
generate collision errors. We will use the new arbitration driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The new driver supports driver model and configuration via device tree. Add
a node for pit, which needs this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a description of the snow memory layout to assist flashing tools which
want to be able to deal with any exynos image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Line up the display with the line below, e.g.:
CPU: Exynos5250 @ 1.7 GHz
Model: Google Spring
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0
Also show the speed as GHz where appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
On pit and pi the TPS65090 regulator is connected only to the EC and we
must use a tunnel to get to it. The existing U-Boot support relies on a
special driver. Add a tunnel definition so that the new device-model
TPS65090 driver can be used unmodified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Snow and smdk5250 use a max77686 PMIC. We have a driver for this, so add
the relevant node to the device tree so it can be used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The kernel uses upper case for I2C unit addresses. Follow the same
convention to reduce differences.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Added PLL variables (dividers mask/shift, lock enable/detect, etc.)
to new pllinfo struct for each Soc/PLL. PLLA/C/D/E/M/P/U/X.
Used pllinfo struct in all clock functions, validated on T210.
Should be equivalent to prior code on T124/114/30/20. Thanks
to Marcel Ziswiler for corrections to the T20/T30 values.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs
to be measured - should be close to 700MHz (1.4G/2).
Note that some freqs aren't in the PLLU table in T210 TRM
(13, 26MHz), so I used the 12MHz table entry for them. They
shouldn't be selected since they're not viable T210 OSC freqs.
Since there are now 2 new OSC defines, all tables (pll_x_table,
PLLU) had to increase by two entries, but since 38.4/48MHz are
not viable osc freqs on T20/30/114, etc, they're just set to 0.
Signed-off-by: Tom Warren <twarren@nvidia.com>
CPU board (E2530) has a fan - turn it on via GPIO to keep
the SoC cool.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL's cache line size is 64bytes, need to
define the macro CONFIG_SYS_CACHELINE_SIZE to 64 for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Update imx register base address for i.MX6UL.
2. Remove duplicated MXS_APBH/GPMI/BCH_BASE.
3. Remove #ifdef for register addresses that equal to
"AIPS2_OFF_BASE_ADDR + 0x34000" for different chips.
4. According fuse map, complete fuse_bank4_regs.
5. Move AIPS3_ARB_BASE_ADDR and AIPS3_ARB_END_ADDR out of #ifdef CONFIG_MX6SX,
because we can use runtime check
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime from
DIGPROG register. But the value has been occupied by MXC_CPU_MX6D which
is not real id from DIGPROG register, so change i.MX6D to value 0x67 which
was not occupied.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since the i.MX6QP has fixed the issue in boot ROM, so remove the workaround
for i.MX6QP.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.
In c files, use runtime check and discard #ifdef.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add cpu type for i.MX6QP/DP.
This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Added routine mmu_set_region_dcache_behaviour() to set a
particular region as non cacheable.
Define dummy routine for mmu_set_region_dcache_behaviour()
to handle incase of dcache off.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All based off of Tegra124. As a Tegra210 board is brought
up, these may change a bit to match the HW more closely,
but probably 90% of this is identical to T124.
Note that since T210 is a 64-bit build, it has no SPL
component, and hence no cpu.c for Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Moved Tegra config options to mach-tegra/Kconfig so that both
32-bit and 64-bit builds can co-exist for Tegra SoCs.
T210 will be 64-bit only (no SPL) and will require a 32-bit
AVP/BPMP loader.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon's 'tegra124: Implement spl_was_boot_source()' needs
a prototype for save_boot_params_ret() to build cleanly
for 64-bit Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
A subsequent patch will enable the use of the architected timer on
ARMv8. Doing so implies that udelay() will be backed by this timer
implementation, and hence the architected timer must be ready when
udelay() is first called. The first time udelay() is used is while
resetting the debug UART, which happens very early. Make sure that
arch_timer_init() is called before that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On 64-bit SoCs the I-cache isn't enabled in early code, so the default
cache enable functions for 64-bit ARM can be used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most peripherals on Tegra can do DMA only to the lower 32-bit
address space, even on 64-bit SoCs. This limitation is
typically overcome by the use of an IOMMU. Since the IOMMU is
not entirely trivial to set up and serves no other purpose
(I/O protection, ...) in U-Boot, restrict 64-bit Tegra SoCs to
the lower 32-bit address space for RAM. This ensures that the
physical addresses of buffers that are programmed into the
various DMA engines are valid and don't alias to lower addresses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
While generating the page tables, a running integer index is shifted by
SECTION_SHIFT (29) and causes overflow for any integer bigger than 7.
The page tables therefore alias to the same 8 sections and cause U-Boot
to hang once the MMU is enabled.
Fix this by making the index a 64-bit unsigned integer and so avoid the
overflow.
swarren notes: currently "i" ranges from 0..8191 on all ARM64 boards, and
"j" varies depending on RAM size; from 4 to 11 for a board with 4GB at
physical address 2GB, as some Tegra boards have.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds the two MIO connected pushbuttons on the zc702 board to the
devicetree as a single multi-key device for us with the gpio-keys driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add pl310 interrupt to the Zynq devicetree.
Signed-off-by: Alex Wilson <alex.david.wilson@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unneeded address-cells form intc node because it is already setup
in parent node.
Add missing address-cells and size-cells to eth node to be shared for
every platform DTSes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass directly boot_addr which is LOVEC (0) or HIVEC (0xffff0000).
No reason to use magic values 0 and 1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynqmp Kconfig from board to arch
as there may be different boards under same
architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The encoding of the sub instruction used to handle CONFIG_SYS_MALLOC_F_LEN
can only accept certain values, and the set of acceptable values differs
between the AArch32 and AArch64 instructions sets. The default value of
CONFIG_SYS_MALLOC_F_LEN works with either ISA. Tegra uses a non-default
value that can only be encoded in the AArch32 ISA. Fix the AArch64 crt0
assembly so it can handle completely arbitrary values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[twarren: trimmed Thierry's patch to remove changes already present]
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, cleaned up patch, wrote description, re-wrote subject]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, stripped out changes not strictly related to warnings]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While most stm32f4 run at 168 MHz, stm32f429 can work till 180 MHz.
Add option to select 180 MHz through macro CONFIG_SYS_CLK_FREQ.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This cleans up the SPL boot devices for omap platforms and introduces support
for missing boot devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When core A turning of core B, via tetris DPSC it places the core
B DPSC into transitional state. The core B has to execute wfi instruction
to move its DPSC to the OFF state. This patch add such instruction.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This allows using devices plugged into both ports of the tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
At one point in time the utoo-p66 dts file in the kernel had a bogus
uart entry, and it seems like we synced with the kernel at just the wrong
moment.
This commit removes the bogus uart entry, which breaks booting the utoo-p66
when DM_SERIAL=y.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds basic SDIO/MMC booting support to MVEBU SoC's. Since
I don't know of a way to test the boot-device upon runtime, this patch
hardcodes the spl_boot_device instead.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the record, describe exactly which device of which vendor
is used on this board.
I2C EEPROM is bound by the generic compatible string, "i2c-eeprom",
so this commit has no impact on the functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x SPL support, which is not
compatible to the Armada XP SERDES init code, we need to introduce a new
directory infrastructure. So lets move the AXP serdes init code into
a new directory. This way the A38x code can be added in a clean way.
Signed-off-by: Stefan Roese <sr@denx.de>
Only with disabled MMU its possible to switch the base register address on
Armada 38x. Without this the SDRAM located at >= 0x4000.0000 is also not
accessible, as its still locked to cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Pin muxing needs to be done before UART output, since on A38x the UART
pins need some re-muxing for output to work.
Signed-off-by: Stefan Roese <sr@denx.de>
On A38x switching the regs base address without running from
SDRAM doesn't seem to work. So let the SPL still use the
default base address and switch to the new address in the
mail u-boot later.
Signed-off-by: Stefan Roese <sr@denx.de>
Without calling timer_init(), the xdelay() functions return immediately.
We need to call timer_init() early, so that these functions work and
the PHY and DDR init code works correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Since we want clk_ops to be used in U-Boot as a whole, rename the Zynq
version until it can be converted to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver-model I2C drivers can be picked up by the linker script rule for
legacy drivers. Change the order to avoid this.
We could make the legacy code depend on !CONFIG_DM_I2C but that is not
necessary and it is good to keep conditions to a minimum.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL device tree size must be minimised to save memory. Only include
properties that are needed by SPL - this is determined by the presence
of the "u-boot,dm-pre-reloc" property. Also remove a predefined list of
unused properties from the nodes that remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add dts source files for LS2085AQDS and LS2085ARDB boards.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bring in required device tree files for ls2085a from Linux. These are
initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR speed should be in MT/s, not MHz.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.
Note we've never shipped a final u-boot version with the old name, so this
is safe todo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The root cause of this problem should now be fixed.
This reverts commit a6a4c542d3.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
When CONFIG_SYS_THUMB_BUILD is defined these functions may be called from
Thumb code. Add the required ENTRY and ENDPROC bracketing so that BLX is
used to call these ARM functions, instead of plain BL, which will fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pavel Machek <pavel@denx.de>
Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2.
This adds a dts file for Sinlinx SinA33 dev board, and the required
changes in the .dtsi files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds the device tree binding doc for the cadence qspi controller &
also removes the not needed properties from the stv0991 device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch add the device tree entry for qspi controller & spi flash
memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, the device trees for UniPhier
SoCs and boards have already been dual-licensed in Linux.
Follow this trend in U-boot too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes code diff much easier.
Device trees describe hardware attributes, which are independent
of software architecture. It generally makes sense to synchronize
them beyond software projects.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Enabled CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH for zynq soc.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
Add a new revision CHIP_REV_2_0.
Introudce macro is_mx6dqp, dqp means Dual/Quad Plus.
Since Dual/Quad Plus use same cpu type with Dual/Quad, but different
revision(Major Lower), we use this macro for Dual/Quad Plus.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
