The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This fixes the following genboardscfg.py warnings:
---8<---
WARNING: no status for 'at91sam9g20ek_2mmc'
WARNING: no maintainers for 'at91sam9g20ek_2mmc'
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This fixes following genboardscfg.py warning:
---8<---
WARNING: no status for 'at91sam9rlek_mmc'
WARNING: no maintainers for 'at91sam9rlek_mmc'
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
On these boards the DDR is connected to a dedicated controller and not
to chip select 1 of the EBI.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Tested-by: Erik van Luijk <evanluijk@interact.nl>
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase on ToT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The board select menu in arch/arm/Kconfig is still big.
To slim down it, this commit moves AT91 boards to
arch/arm/mach-at91/Kconfig.
Also, consolidate "config SYS_SOC" in each board Kconfig.
The Kconfig files under board/ directory were modified with the
following command:
find board -name Kconfig | xargs sed -i -e '
/config SYS_SOC/ {
N
/default "at91"/ {
N
d
}
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
Prefix mmu.h PAGE_xxx definitions with MMU_ in order to prevent a naming
conflict with other definitions.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
- "string" type for SYS_* is defined in arch/Kconfig
- SYS_CPU "armv7" has been replaced with "select CPU_V7"
- SYS_SOC "tegra124" is already defined in tegra124/Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The "S: Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")
For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
N
/S:[[:blank:]]Orphan/s/^/#/
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add NOR flash hardware init function, including SMC and PIO
configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Also we enable the mmc command in configuration file.
As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
It supports boot from NAND and SD/MMC card.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add NAND SPL boot support with hardware PMECC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add SPI SPL boot support for sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
- NAND flash
- SD/MMC card
- Two USB hosts
- Ethernet (one GMAC, one EMAC)
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[reorder boards.cfg]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.
Please note that this hooks up slot1 (MCI1) for SD. Not both.
Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).
CONFIG_ATMEL_MCI_PORTB not tested.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable the PIO peripherals early than other peripherals.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12
and share the lower 8 bits data line. If use low drive of the data
line, it will cause DDR data access corrupt in lower address, so
change the data line to high drive mode
This will fix the Linux kernel boot issue when use Lower address
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
add network support with ksz8851_16mll on at91sam9n12ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for following features:
- nand boot, with PMECC 2bit ECC for 512 bytes sector
- SPI flash boot
- SD card boot
- LCD support
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix -Wimplicit-function-declaration for at91_lcd_hw_init()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add at91sam9g20_2mmc nand boot support. on this board, there is no
dataflash, so disable it
change one commet for at91sam9g20ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register).
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch is derived from an older patch provided by atmel in its
buildroot-avr32-v3.0.0.tar.bz2
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Jens Scharsig <esw@bus-elektronik.de>
cc: Stelian Pop <stelian@popies.net>
cc: Sedji Gaouaou<sedji.gaouaou@atmel.com>
cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
cc: Eric Benard <eric@eukrea.com>
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
fix a bug:
when not boot from NAND, the NAND flash can not be detected.
Using this to fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00042000
fs 0x00252000
u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.
Now, the layout is:
bootstrap 0x00000000
ubootenv 0x00004200
uboot 0x00008400
kernel 0x00084000
fs 0x00294000
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Fix board part of AT91SAM9261-EK according to the new scheme
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch removes the board implemenatation for flash driver which can now
safely switched to the common cfi driver.
Compile tested for all atstk100x boards, runtime tested on atstk1002.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
This patch move the atstk100x linker script to $(CPUDIR) and delete other
pure copies of this file in each board directory.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
This patch removes PLATFORM_RELFLAGS from board specific config.mk files and
define them in arch specific config.mk file.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>