cscope complains that it can't find files that appears to be symbolic links
cscope: cannot find file tools/binman/test/u_boot_binman_syms_bad.c
cscope: cannot find file tools/version.h
`find -L` tests properties, but name, and cscope can't cope with symbolic
links (a lot of bugs in upstream were simple closed as kinda invalid).
To work around the problem, exclude symbolic links from the cscope.files.
Note, it's done in two pass to speed up the process (`-exec realpath ...`
approach is not portable and introduces a 3x delay).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Support a new BINMAN_VERBOSE option to the build, to allow passing the
-v flag to binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Pass in the toolpath in case binman needs to use tools compiled in the
U-Boot tools/ directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
*.pyc files contain compiled Python bytecode. 'make mrproper' should remove
them.
Removing *.pyc files helps for instance sometimes when running into an
error "binman: Unknown entry type 'blob' in node '/binman/blob'".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For many sub-systems we already require the driver model to be used. Yet
there is still a handful of boards that do not have CONFIG_DM enabled.
We should make CONFIG_DM compulsory with release v2020.01
Conversion dates for CONFIG_DM_SPL and CONFIG_DM_TPL are yet to be defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many Rockchip platforms require the same u-boot deploy procedure
when TPL and SPL both enabled.
The following examples are taken from doc/README.rockchip
and board/theobroma-systems/lion_rk3368/README:
RK3288:
./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/mmcblk0 seek=64
RK3328:
./tools/mkimage -n rk3328 -T rksd -d ./tpl/u-boot-tpl.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64
RK3368:
./tools/mkimage -n rk3368 -T rksd -d tpl/u-boot-tpl.bin spl-3368.img
cat spl/u-boot-spl-dtb.bin >> spl-3368.img
dd if=spl-3368.img of=/dev/sdb seek=64
RK3399:
./tools/mkimage -n rk3399 -T rksd -d ./tpl/u-boot-tpl-dtb.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/sdc seek=64
Here, we introduce generic idbloader.img target
which is the TPL image followed by the SPL binary.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The driver model has been supported for network drivers since 2015. It is
time to convert the remaining boards. Set July 2020 as a timeline.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I wanted this to be compatible with mkenvimage, including the ability
to embed newlines in variables by escaping them. But I failed to check
that it works more than once.
Fixes: f3d8f7dd73 (Allow providing default environment from file)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
TI AM65x platforms (evm and HS) generate an SPL image
'tispl.bin*' and there is no rule for cleanup.
Added entry for cleanup in clean target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Support of device tree model for T2080RDB, T4240RDB, T1024RDB,
T1042D4RDB, P1020RDB, P2020RDB, P2041RDB, P3041DS, P4080DS, P5040DS and
MPC8548CDS. Also support of i2c dm model.
The current Makefile always use u-boot.bin to generate
PBL boot image (u-boot.pbl), this patch changes it to
use u-boot-with-dtb.bin to support device tree when
CONFIG_OF_SEPARATE is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
When building a U-Boot FIT image, the device trees specified by the
board are unconditionally built for inclusion in the FIT image. However,
not all device tree providers, such as CONFIG_OF_PRIOR_STAGE, require a
device tree to be built and bundled with the U-Boot binary. They rely on
other mechanisms to provide the device tree to U-Boot. Compilation on
boards with these device tree providers fails, because they do not
specify a device tree.
Change the makefile rules to conditionally build the device trees if
CONFIG_OF_SEPARATE, CONFIG_OF_EMBED, or CONFIG_OF_HOSTFILE is selected
as device tree provider.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
There are no more users of the compatibility layer for i2c. Remove the
driver and all references to it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
There are no more "real" users of CONFIG_DM_I2C_COMPAT and we'll soon
remove it altogether. Stop building it in sandbox mode.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
binman only accepts the -D argument early on the command-line, yet the
Makefile currently passes it near the end. This causes the build to fail
if this feature is used. Re-order the command-line to fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This class is the new way to handle arguments in Python. Convert binman
over to use it. At the same time, introduce commands so that we can
separate out the different parts of binman functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Right now rockchip platform need to copy bl31.elf into u-boot
source directory to make use of building u-boot.itb.
So, add environment variable BL31 like Allwinner SoC so-that the
bl31.elf would available via BL31.
If the builds are not exporting BL31 env, the make_fit_atf.py
explicitly create dummy bl31.elf in u-boot root directory to
satisfy travis builds and it will show the warning on console as
WARNING: BL31 file bl31.elf NOT found, resulting binary is non-functional
WARNING: Please read Building section in doc/README.rockchip
Note, that the dummy bl31 files were created during not exporting
BL31 case would be removed via clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Rockchip platform has its python script that would generate various
bl31_*bin for creating u-boot.itb file by taking bl31.elf as input.
These bl31_*.bin files are generated in u-boot root directory and
have no rule to clean it up. so add support for it by adding in
command entry of clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
binman tools for creating single image build will create image.map
at the end, which has information about binman image node details.
current u-boot, is unable to clean this image.map so add a command
entry in clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ad7061ed74 ("doc: Move device tree bindings documentation to
doc/device-tree-bindings") moved all device tree binding documentation
to doc/device-tree-bindings directory.
The current U-Boot project still have two documentation directories:
- doc/
- Documentation/
Move all documentation and sphinx files to doc directory so all content
can be in a common place.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
We have a warning text for non dm converted spi drivers, but the plan is
to mark all these respective drivers with CONFIG_DEPRECATED.
So, trigger a warning saying that these driver configurations and
associated code will remove in v2019.07 (earlier plan is to remove it
from v2019.04)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
If configured target has deprecated configs enabled, trigger a warning
about this.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[trini: Change from BROKEN to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
A new configuration variable CONFIG_SPL_SIZE_LIMIT is introduced to define
the board specific maximum size for the SPL file.
Use Makefile function size_check() to implement the test.
Depending on the size of CONFIG_SPL_SIZE_LIMIT an error like the following
is thrown:
spl/u-boot-spl.bin exceeds file size limit:
limit: 30720 bytes
actual: 33426 bytes
excess: 2706 bytes
make: *** [Makefile:1663: spl/u-boot-spl.bin] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Carve out function size_check from macro BOARD_SIZE_CHECK. This will allow
us to reuse the function for other file size checks.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like the
following is thrown:
u-boot-dtb.img exceeds file size limit:
limit: 409516 bytes
actual: 444346 bytes
excess: 34830 bytes
make: *** [Makefile:1212: u-boot-dtb.img] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is causing unexpected size growth in the normal case and is likely
to have been mis-applied by myself.
This reverts commit 3eaf6dcd93.
Signed-off-by: Tom Rini <trini@konsulko.com>
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support for compressed fit-dtb.blob was added in:
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
When building compressed (lzop, gzip) fit-dtb.blob images, the
compression tool may embed the time or umask in the image.
Work around this by manually setting the time of the source file using
SOURCE_DATE_EPOCH and a hard-coded 0600 umask.
With gzip, this could be accomplished by using -n/--no-name, but lzop
has no current workaround:
https://bugs.debian.org/896520
This is essentially the same fix applied to multi-dtb fit SPL images in:
commit 8664ab7deb ("Set time and umask on multi-dtb fit images to
ensure reproducibile builds.")
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Support for compressed fit-dtb.blob was added in:
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
Adjust Makefile to also clean compressed blobs.
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
As much of the watchdog system has been migrated to DM now, formalize a
deadline for migration.
Please note that the old CONFIG_HW_WATCHDOG macro should be removed
completely at some point.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
At present we support having 16-bit init be in SPL or U-Boot proper, but
not TPL. Add support for this so that TPL can boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The initial environment is linked to the u-boot binary. Modifying the
environment from User Space with the env tools requires that the tools
are always built together with the bootloader to be sure that they
contain the initial environment in case no environment is stored into
persistent storage or when a board boots with just the default
environment. This makes difficult for distros to provide a general
package to access the environment. A simpler way is if the tools are
generic for all boards and a configuration file is given to provide the
initial environment.
The patch just generates the initial environment by extracting it from
the compiled object. This file can then be used for tools in user space
to initialize the environment.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_AHCI & CONFIG_BLK by itself, as that is not a bug.
This was detected when converting the Armada XP SATA driver sata_mv.c
to DM with AHCI & BLK support. This warning is still printed without
this patch applied here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add required Kconfig symbols, Makefile bits and macro fixes in a
few places to support LZO and DT compression in U-Boot. This can
save a lot of space with multi-DTB fitImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that
shall be used to generate the combined SPL + U-Boot image. The default
value is the current value "spl/u-boot-spl.bin".
This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets
which use SPL NAND support (boot from NAND). For these build targets the
combined image "u-boot-with-spl.bin" is now automatically generated and
can be programmed into NAND as one single image (vs. SPL image and U-Boot
as 2 separate images).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
When the SPL has full fitImage support, do not generate fitImage with
external data. The full fitImage code assumes the entire fitImage is
loaded in RAM, and the SPL uses fdt_totalsize() to determine the size
of the whole fitImage, which can not work with external data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
If `make mrproper` does not delete the generated drivers/video/fonts/*.S
files a following `make tests` fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The last parameter is expected to be the imagefile. Since -E is a
flag having the output name before -p will make mkimage ignore the
external offset option.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
With the current Makefile, CONFIG_BOARD_SIZE_LIMIT is used to check
the U-Boot binary without devicetree only. This produces wrong results
when OF_SEPARATE is used.
To fix this, run the CONFIG_BOARD_SIZE_LIMIT check on all .img binaries
as well.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Multiple people have reported intermittent build failure in parallel
building.
Kever Yang reported this issue some time ago [1], but I could not
get enough clue at that time.
This time, Richard Purdie provided a full build log [2], which was
very helpful for me to root-cause it.
The cause of the problem is commit 0d982c5853 ("Makefile: add
dependencies to regenerate u-boot.cfg when lost").
That commit added the 'cfg' as the prerequisite of the 'all' target,
so the parallel build tries to run it simultaneously, then regenerates
a symlink while building objects.
When u-boot.cfg is accidentally lost, let's rebuild it before
descending into any subdirectories.
Also, what is annoying is u-boot.cfg is currently regenerated every
time since it depends on FORCE. We can get rid of all the prerequisites
of u-boot.cfg because u-boot.cfg is rebuilt anyway as the byproduct of
auto.conf when a user updates the .config file.
[1] https://lists.denx.de/pipermail/u-boot/2018-June/330341.html
[2] https://autobuilder.yoctoproject.org/typhoon/#/builders/65/builds/160/steps/7/logs/step1b
Fixes: 0d982c5853 ("Makefile: add dependencies to regenerate u-boot.cfg when lost")
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no need to compile and include this code if it is not used.
CONFIG_USB_GADGET can be used for the purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The mkimage_fit_atf.sh SPL FIT generator script requires
u-boot-nodtb.bin, but this was not enforced by the Makefile. This could
cause the generator script to be executed before u-boot-nodtb.bin has
been created.
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_DM_SCSI by itself, as that is not a bug.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: ea9d7c17fc ("dm: MIGRATION: Add migration plan for CONFIG_SATA")
Signed-off-by: Tom Rini <trini@konsulko.com>
- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.
Note: there were many updates on this deadline, so better
not update this again.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Output the device model migration warnings to stderr. This allows tools
like buildman to pick them up rather than suppressing them along with
the normal build output on stdout.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The contents of the test subdirectories only make sense when we have
CONFIG_UNIT_TEST set. We will otherwise attempt to build code on for
example sandbox that needs CONFIG_UNIT_TEST otherwise and rather than
complicate the Makefiles simply leave them out when we can.
Signed-off-by: Tom Rini <trini@konsulko.com>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Soeren Moch <smoch@web.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As much of the USB system has been migrated to DM now, formalize a
deadline for migration.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
