Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[hdegoede@redhat.com] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
According to the datasheets the max speed of AHB1 is 276 MHz, so
setting it to PLL6 / 3 which gives us 200MHz everywhere is fine,
and gives us a nice speed-up in certain workloads.
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Chen-Yu Tsai <wens@csie.org>
GRF is the gereral register file. Add header files with register definitions.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for setting up and modifying the various PLLs, peripheral
clocks and mmc clocks on RK3036
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
some rockchip soc will not include lib/timer.c in SPL stage,
so implement timer driver for some soc can use us delay function in SPL.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The early MMU table doesn't enable all addresses. Unused addresses
are marked as invalid, as introduced by commit 9979922. An entry
was missing for NAND flash space, causing nand boot failure.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We should also take MX6D option in consideration when defining
imx_iomux_v3_setup_pad().
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Introudce a new function lcdif_power_down.
1. Waits for a VSYNC interrupt to guarantee the reset is done at the
VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.
The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
building error for mxsfb.c, since mxsfb.c use imx-regs.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Rename GPU functions to less generic names to avoid potential name
collisions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no justification for this function, especially in exported
form.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
