Memory controller code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The GP pad control code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clock code is not relevant on all Tegra SoC generations, so guard it
with a Kconfig symbol that can be selected by the generations that need
it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There's no need to replicate the pmu.h header file for every Tegra SoC
generation. Use a single header that is shared across generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pll_c is not a valid parent for the disp1 clock, so trying to set it
will fail. Given that display is not used in U-Boot, remove the init
table entry so that disp1 will keep its default parent (clk_m).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra210 the parents for the disp1 and disp2 clocks are slightly
different from earlier chips. Only pll_p, pll_d_out0, pll_d2_out0 and
clk_m are valid parents (technically pll_d_out is as well, but U-Boot
doesn't know anything about it). Fix up the type name and the mux
definition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function can be used to set the local MAC address for the default
Ethernet interface in its device tree node. The default interface is
identified by the "ethernet" alias.
One case where this is useful is for devices that store their MAC
address in a custom location. Once extracted, board code can store the
MAC address in U-Boot's control DTB so that it will automatically be
used by the Ethernet uclass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Support Microchip MPFS Icicle board.
- Enable e1000 and nvme support for qemu.
- Enable PCI host ECAM generic driver for qemu.
- Increase the environment size to 128kB for qemu.
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The existing default size of 4kB is too small as the default environment
has already nearly that size and defining a single additional environment
variable can exceed the available space.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Corrections for boottime services for protocols and for the SetTime()
service are provided.
Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are
added.
-----BEGIN PGP SIGNATURE-----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=A8+f
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc4' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc4
Corrections for boottime services for protocols and for the SetTime()
service are provided.
Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are
added.
Provide a unit test that checks that the open protocol information is
correctly updated when opening and closing protocols.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CloseProtocol() must delete all open protocol information records relating
to import parameters not only one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When a protocol is opened the open protocol information must be updated.
The key fields of the open protocol information records are ImageHandle,
ControllerHandle, and Attributes.
Consider the Attributes field when determining if an open protocol
information record has to be updated or a new one has to be created.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI specification requires that when a protocol is opened via
HandleProtocol() the agent handle is the image handle of the EFI firmware
(see chapter on EFI_BOOT_SERVICES.OpenProtocol()).
Let efi_handle_protocol() pass efi_root as agent handle to
efi_open_protocol().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Alex reported the following:
"
I'm doing some MDIO work on a freescale/NXP platform and I bumped into
errors with this command:
=> mdio r emdio#3 5 3
Reading from bus emdio#3
"Synchronous Abort" handler, esr 0x8600000e
elr: ffffffff862b8000 lr : 000000008200cce4 (reloc)
...
mdio list does not list any PHYs currently because ethernet is using DM
and the interfaces are not probed at this time. The PHY does exist
on the bus though.
The above scenario works with this commit reverted:
e55047ec51 cmd: mdio: Switch to generic
helpers when accessing the registers
The current code using generic helpers only works for PHYs that have
been registered and show up in bus->phymap and crashes for arbitrary
IDs. I find it useful to allow reading from other addresses over MDIO
too, certainly helpful for people debugging MDIO on various boards.
"
Fix this by reverting to use the raw MDIO bus operations in case there
is no PHY probed based on DT at the specified address.
This restores the old behavior for these PHYs, which means that the
newly introduced MMD-over-C22 helpers won't be available for them, but
at least they will be accessible again without crashing the system.
Fixes: commit e55047ec51 ("cmd: mdio: Switch to generic helpers when accessing the registers")
Reported-by: Alex Marginean <alexm.osslist@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
At present the link speed change callback is a nop. According to
macb device tree bindings, an optional "tx_clk" is used to clock
the ethernet controller's TX_CLK under different link speed.
In 10/100 MII mode, transmit logic must be clocked from a free
running clock generated by the external PHY. In gigabit GMII mode,
the controller, not the external PHY, must generate the 125 MHz
transmit clock towards the PHY.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This updates DM version macb_linkspd_cb() signature for future
expansion, eg: adding an implementation for link speed changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds a clock driver to support the GEMGXL management IP block
found in FU540 SoCs to control GEM TX clock operation mode for
10/100/1000 Mbps.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Add the standard Ethernet device tree bindings (imported from v5.0 of
the Linux kernel) and implement support for reading the MAC address for
Ethernet devices in the Ethernet uclass. If the "mac-address" property
exists, the MAC address will be parsed from that. If that property does
not exist, the "local-mac-address" property will be tried as fallback.
MAC addresses from device tree take precedence over the ones stored in
a network interface card's ROM.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order for the device to use the proper MAC address, which can have
been configured in the environment prior to the device being registered,
ensure that the MAC address is written after the device has been probed.
For devices that are registered before the network stack is initialized,
this is already done during eth_initialize(). If the Ethernet device is
on a bus that is not initialized on early boot, such as PCI, the device
is not available at the time eth_initialize() is called, so we need the
MAC address programming to also happen after probe.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The GetTime() and the SetTime() runtime services are not obligatory. So
let's make them customizable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If SetTime() is meant to set daylight saving time it will be called with
Time.Daylight == EFI_TIME_ADJUST_DAYLIGHT | EFI_TIME_IN_DAYLIGHT.
Return 0 from GetTime() if time is not in daylight because we cannot
determine if we are in a time zone with daylight saving time.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To let a board implement the runtime version of SetTime() we have to
provide the definition of the weak function in an include.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI spec prescribes that we check that the timestamp passed to
SetTime() is checked for validity.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uninstalling a protocol the following steps are needed:
* request all drivers to disconnect
* close protocol for all non-drivers
* check if any open instance of the protocol exists on the handle and
return EFI_ACCESS_DENIED in this case
* remove the protocol interface
By tort we tested for remaining open protocol instances already after
requesting drivers to disconnect.
With this correction the UEFI SCT II tests for UninstallProtocolInterface()
and ReinstallProtocolInterface are passed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When trying to open a protocol exclusively attached drivers have to be
removed. This removes entries in the open protocol information linked list
over which we are looping. As additionally child controllers may have been
removed the only safe thing to do is to restart the loop over the linked
list when a driver is removed.
By observing the return code of DisconnectController() we can eliminate a
loop.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In LocateProtocol() implement searching by the registration key returned by
RegisterNotifyProtocol().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The code to check if a registration key is a valid key returned by
RegisterProtocolNotify() can be reused. So let us factor it out into a new
function efi_check_register_notify_event().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If a user defines BootNext but not BootOrder and loading from BootNext
fails, you will see only a message like this:
BootOrder not defined
This may confuse a user. Adding an error message will be helpful.
An example output looks like this:
=> efidebug boot add 0001 label1 scsi 0:1 "\path1\file1.efi" "--option foo"
=> efidebug boot add 0002 label2 scsi 0:1 "\path2\file2.efi" "--option bar"
=> efidebug boot add 0003 label3 scsi 0:1 "\path3\file3.efi" "--option no"
=> efidebug boot order 0001 0002
=> efidebug boot next 0003
=> bootefi bootmgr
Loading from Boot0003 'label3' failed
Loading from BootNext failed, falling back to BootOrder
Loading from Boot0001 'label1' failed
Loading from Boot0002 'label2' failed
EFI boot manager: Cannot load any image
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Adjust messages.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Error message will alert a user that setting/deleting a variable failed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When a protocol is installed the handle should be queued for the
registration key of each registered event. LocateHandle() should return the
first handle from the queue for the registration key and delete it from the
queue.
Implement the queueing.
Correct the selftest.
With the patch the UEFI SCT tests for LocateHandle() are passed without
failure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
- Add USB clock support that was introduced in 5.2-rc1 bindings
- Add currently in-review for Linux eMMC & USB DT for G12A in -u-boot.dtsi
- Fix PHY routing to external PHY when chainloading from a misconfigred bootloader
- Remove useless PHY GPIO reset from q200 board file
- Enable USB support for Amlogic U200 reference board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fY1N
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190531' of git://git.denx.de/u-boot-amlogic
- Sync DT with Linux 5.2-rc1 for G12A
- Add USB clock support that was introduced in 5.2-rc1 bindings
- Add currently in-review for Linux eMMC & USB DT for G12A in -u-boot.dtsi
- Fix PHY routing to external PHY when chainloading from a misconfigred bootloader
- Remove useless PHY GPIO reset from q200 board file
- Enable USB support for Amlogic U200 reference board
Now the Amlogic G12A DT and drivers are present, enable full USB
on the U200 Reference Design board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When using External PHY, reset the mux to use the external PHY in case U-Boot
was chainloaded from a misconfigured bootloader.
Fixes: 33e3378091 ("ARM: meson: rework soc arch file to prepare for new SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The following DT nodes in the process on review for Linux 5.3,
until Linux 5.3 is tagged, add the missing DT nodes in u-boot specific
DTSI files that will be dropped when the v5.3-rc1 DT is synced again.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The G12A PCIE PLL clock was introduced in Linux 5.2-rc1, and is needed
for USB to operate, add basic support for it and associated gates.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch add documentation for TPL build and flashing steps
for rk3399 boards.
Add full boot log for future reference.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
