The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Also remove setting phy->dev to NULL now that generic_phy_get_by_name()
properly initialize phy->dev to NULL.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Make usage of clock and reset bulk API in order to simplify the code
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
EHCI is usually used with companion controller (like OHCI) as companion
controller. This information on the companion is missing currently in
companion drivers.
So, if the usb-uclass isn't aware, it may scan busses in any order: OHCI
first, then EHCI.
This is seen on STM32MP1 where DT probing makes the probe order to occur
by increasing address (OHCI address < EHCI address).
When a low speed or full-speed device is plugged in, it's not detected as
EHCI should first detect it, and give ownership (handover) to OHCI.
Current situation on STM32MP1 (with a low speed device plugged-in)
STM32MP> usb start
starting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800c000 for devices... 1 USB Device(s) found
scanning bus usb@5800d000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
The "companion" property in the device tree allow to retrieve companion
controller information, from the EHCI node. This allow marking the
companion driver as such.
With this patch (same low speed device plugged in):
STM32MP> usb start
starting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800d000 for devices... 1 USB Device(s) found
scanning bus usb@5800c000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Human Interface (1.5 Mb/s, 100mA)
HP HP USB 1000dpi Laser Mouse
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
This also optimize bus scan when a High speed device is plugged in, as
the usb-uclass skips OHCI in this case:
STM32MP> usb reset
resetting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800d000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 200mA)
SanDisk Cruzer Blade 03003432021922011407
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The original logic always enables USB_DR_MODE_HOST operation mode in
dwc3_layerscape_bind() in u-boot. Prevent choosing USB_DR_MODE_HOST
operation mode if USB_HOST is not enabled.
Fixes: 2b0b51d0be ("usb: dwc3: add layerscape support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
In the usb/dwc3-layerscape driver the first option should be renamed
to the latter as well. Do it.
Fix original logic in dwc3_layerscape_bind() - do not enable
Fixes: 333e4a621d ("Rename SPL_USB_HOST_SUPPORT to SPL_USB_HOST")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
As ulpi_reset gpio is now optional, we need to check it when doing
the 'dwc3_generic_remove' function. Check if it is declared before
accessing the ulpi_reset.
Fixes: 237d1f60b1 ("usb: dwc3: Use the devm_gpiod_get_optional()
API for reset gpio")
Reported-by: Thomas Nizan <tnizan@witekio.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Reviewed-by: Marek Vasut <marex@denx.de>
When USB finds no devices it currently returns -EPERM which bootstd does
not understand. This causes other bootdevs of the same priority to be
skipped.
Fix this by returning the correct error code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the ethernet gadget driver registration and removal from ethernet
bind and unbind callbacks into driver DM probe and remove callbacks.
This way, when the driver is bound, which is triggered deliberately
using 'bind' command, the USB ethernet gadget driver is instantiated
and bound to the matching UDC. In reverse, when the driver is unbound,
which is again triggered deliberately using 'unbind' command, the USB
ethernet gadget driver instance is removed.
Effectively, this now behaves like running either 'ums' or 'dfu' or
any other commands utilizing USB gadget functionality.
This also drops use of usb_gadget_release() and moves the use of
usb_gadget_initialize() into usb_ether_init() used only by legacy
platforms that do not use 'bind' command properly yet. Those have
no place in drivers.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move the driver probe function above the driver structure, so it
can be placed alongside other related functions, like upcoming
remove function. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions here are only ever called once since drop of non-DM
networking code. Inline them. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Like Rockchip RK3568, the RK3328 also have single node to
represent the glue and ctrl for USB 3.0.
So, use the driver data to use single ctrl for RK3328 DWC3.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3568 share glue and ctrl in a single node. Use glue_get_ctrl_dev to
return the glue node as the ctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When dr_mode is peripheral or otg and U-Boot has not been built with
DM_USB_GADGET support, booting such device may end up with:
dwc3_glue_bind_common: subnode name: usb@fcc00000
Error binding driver 'dwc3-generic-wrapper': -6
Some drivers failed to bind
initcall sequence 00000000effbca08 failed at call 0000000000a217c8 (err=-6)
### ERROR ### Please RESET the board ###
Instead fail gracfully with ENODEV to allow board continue booting.
dwc3_glue_bind_common: subnode name: usb@fcc00000
dwc3_glue_bind_common: unsupported dr_mode 3
Also use CONFIG_IS_ENABLED(USB_HOST) and change switch to if statements
to improve readability of the code.
Fixes: 446e3a205b ("dwc3-generic: Handle the PHYs, the clocks and the reset lines")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
The current error check for device_find_first_child is not working as
expected, the documentation for device_find_first_child mention:
@devp: Returns first child device, or NULL if none
Return: 0
Change to return early when there is no child node to avoid any possible
null pointer dereference.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
drivers/core/device.c will call `device_free()` after xhci_register
already frees the private device data. This can cause a crash later
during the boot process, observed on aarch64 RPi4b as a synchronous
exception. All callers of xhci_register use priv_auto, so this won't
lead to memory leaks.
Signed-off-by: Richard Habeeb <richard.habeeb@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When one of the functions does not support super speed, the composite
driver forces the gadget to high speed. But the speed is never
configured in the cdns3 gadget driver. So configure the speed
in cdns3_gadget_udc_start just like in the kernel.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove the regulator_set_enable() call from device probe which
resolves a regulator imbalance. This is unnecessary as
regulator_set_enable() will be called when ehci_register calls the
init_after_reset hook.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GPIOD_ACTIVE_LOW is not enough to configure a GPIO as an output, we need
GPIOD_IS_OUT as well.
Fixes: b252d79b09 ("usb: dwc3: Add support to reset usb ULPI phy")
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Fix the write to the HPRT register which treat W1C fields
as if they were mere RW. This leads to unintended clearing of such fields
This bug was found during the testing on Simics model. Referring to
specification DesignWare Cores USB 2.0 Hi-Speed On-The-Go (OTG)
Databook (3.30a)"5.3.4.8 Host Port Control and Status Register (HPRT)", the
HPRT.PrtPwr is cleared by this mistake. In the Linux driver (contrary to
U-Boot), HPRT is always read using dwc2_read_hprt0 helper function which
clears W1C bits. So after write back those bits are zeroes.
Signed-off-by: Teik Heng Chong <teik.heng.chong@intel.com>
In lan78xx_read_otp() we want to know if sig is LAN78XX_OTP_INDICATOR_1
or LAN78XX_OTP_INDICATOR_2. In the case of matching the first one we
set offset to itself, and clang warns about this. Rework the logic so
that if sig is the second indicator we adjust the offset as today and if
it does not match the first indicator we return -EINVAL
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a remnant from when the USB controller driver managed
the reset signal itself. A patch from the very end of 2018 changed
this driver to delegate reset (and clock) management to the proper
control unit driver, but left this unused define behind.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The `musb_register` function returns some ERR_PTR(...) on failure,
not NULL, so update the check here appropriately.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Define SPL_USB_ETH_RNDIS symbol to make it possible to select USB
gadget ethernet support in SPL and U-Boot separately in Kconfig .
Make use of the new symbols in gadget Makefile and move the rndis.o
just below the now merged USB_ETHER symbol in Makefile.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This causes crashes on some boards, e.g. rockpro64. In any case, we
should not do it.
Check the usb_started flag to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_index_ptr instead of the devfdt_get_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the CONFIG_PHY case, move the PHY setup before the register access.
This avoids a hang when updating the imx8mm.dtsi which moves the
USB OTG power-domains to the PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Fabio Estevam <festevam@denx.de>
Avoid incorrect fall through:
A USB_RT_HUB request should not be treated as USB_RT_PORT.
Simplify the coding:
Avoid duplicate debug() statements.
This fixes all -Wimplicit-fallthrough warnings.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Handling of SANDBOX_FLASH_EP_OUT should never fall through to
SANDBOX_FLASH_EP_IN.
This addresses a warning shown when compiling with
-Wimplicit-fallthrough.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building with clang, it notes that sdinfo may be unused
uninitialized in some cases. This appears to be true from reading the
code, and we can simply set the variable to zero to start with and be as
correct as before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The spl_board_prepare_for_boot() should be called before jump_to_image_no_args()
to perform board-specific deinitialization before jumping to the next stage.
This board-specific deinitialization can be very much anything, e.g. disable
dcache in case it was enabled, or such.
Add the missing spl_board_prepare_for_boot() call into f_sdp .
Signed-off-by: Marek Vasut <marex@denx.de>
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes: 5454dea313 ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
There are 4 USB controllers on MT8195, the controllers (IP1~IP3,
exclude IP0) have a wrong default SOF/ITP interval which is
calculated from the frame counter clock 24Mhz by default, but
in fact, the frame counter clock is 48Mhz, so we shall set the
accurate interval according to 48Mhz for those controllers.
Note:
The first controller no need set it, but if set it, shall change
tphy's pll at the same time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Imply means you can turn off the option and expect things to work
- "it's a good idea to have X enabled" is when to use imply
- "you must have X for Y to work" is when to use select
Use "select" here.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
All Nvidia boards use the same manufacturer, vendor ID and product ID
for the gadgets. Make them the defaults to remove some boilerplate from
the defconfigs.
Inspired by commit e02687bda9 ("sunxi: provide default USB gadget
setup") which did the same for Allwinner boards.
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
Make sure the PHY subsystem is activated for the uniphier DWC3 glue
logic, as it depends on PHY implementation there.
Signed-off-by: Marek Vasut <marex@denx.de>
dwc3-uniphier depends on xhci-dwc3 framework, however, it is preferable
to use dwc3-generic.
This driver calls the exported dwc3-generic functions and redefine
the SoC-dependent operations to fit dwc3-generic.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the size of regs property to the glue structure to correctly
specify the register region to map.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to allow external SoC-dependent glue drivers to use dwc3-generic
functions, push the glue structures and export the functions to a header
file.
The exported structures and functions are:
- struct dwc3_glue_data
- struct dwc3_glue_ops
- dwc3_glue_bind()
- dwc3_glue_probe()
- dwc3_glue_remove()
The SoC-dependent glue drivers can only define their own wrapper driver
and specify these functions. The drivers can also add their own compatible
strings and configure functions.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Same as the reset cotnrol, should add a clock initialization in child DT
node, if the glue node doesn't have any clocks.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The most of devicetree has the following USB node structure.
The controller node is placed as a child node of the glue node.
Current dwc3-generic driver works on this premise.
glue {
/* glue node */
usb {
/* controller node */
};
};
However, UniPhier original devicetree has the following USB node structure.
The controller node is separately placed from the glue node.
usb {
/* controller node */
};
glue {
/* glue node */
};
In dwc_glue_bind(), this patch provides .glue_get_ctrl_dev() callback to
get such a controller node and binds the driver related to the node.
If this callback isn't defined, dwc_glue_bind() looks for the controller
nodes from the child nodes, as before.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
There are currently four disparate placement possibilities of DWC3
reference clock phandle in SoC DTs:
- in top level glue node, with generic subnode without clock (ZynqMP)
- in top level generic node, with no subnode (i.MX8MQ)
- in generic subnode, with other clock in top level node (i.MX8MP)
- in both top level node and generic subnode (Rockchip)
Cover all the possibilities here by looking into both nodes, start
with the top level node as that seems to be used in majority of DTs
to reference the clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
As the "reset-gpios" property is optional, don't return the
error and just skip the gpio reset sequence.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
When dropping the unused fotg210 gadget driver a leading 0 was
introduced to the next line, drop it.
Fixes: e9b4678bc7 ("usb: Drop unused fotg210 gadget")
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_USB_MUSB_HOST defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 6 usages of this option to the non-SPL form, since there is
no SPL_IMX_MODULE_FUSE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used and appears to be associated with the faraday board which
has been removed. Drop the driver and Kconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are not used. Drop the drivers and Kconfig option. Also drop an
old declaration in the netdev.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enum clock_osc_freq was designed to use only with T20.
This patch remaps it to use additional frequencies, added in
T30+ SoC while maintaining backwards compatibility with T20.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Thierry Reding <treding@nvidia.com> # T30, T124, T210
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom <twarren@nvidia.com>
When a system has multiple XHCI controllers, some of the
properties described in the descriptor of the root hub (such as
the number of ports) might differ between controllers. Fix this
by switching from a single global hub descriptor to a hub
descriptor per controller.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
An XHCI controller that sits behind an IOMMU needs to map and unmap
its memory buffers to do DMA. Implement this by inroducing new
xhci_dma_map() and xhci_dma_unmap() helper functions. The
xhci_dma_map() function replaces the existing xhci_virt_to_bus()
function in the sense that it returns the bus address in the case
of simple address translation in the absence of an IOMMU. The
xhci_bus_to_virt() function is eliminated by storing the CPU
address of the allocated scratchpad memory in struct xhci_ctrl.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a hunter for USB which enumerates the bus to find new bootdevs.
Update the tests and speed up bootdev_test_prio() while we are here, by
dropping the USB delays.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since usb_find_and_bind_driver() allocates the device name it should tell
driver about that, to avoid memory leaks. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code in these functions turns out to often be the same. Add a default
get_bootflow() function and allow the drivers to select it by setting
the method to NULL.
This saves a little code space.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This variable has never been configured to another value at present, and
was not converted to Kconfig. Opt instead to rename this to
MUSB_TIMEOUT.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Thanks for Mattijs for the original work at [1].
[1] https://lore.kernel.org/all/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com/
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230117-u-boot-usb-gxl-otg-dm-v1-1-2853f6d75b06@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Pullup is used by the usb framework in order to do software-controlled
usb_gadget_connect() and usb_gadget_disconnect().
Implement pullup() for dwc2 using the SOFT_DISCONNECT bit in the dctl
register:
* when pullup is on, clear SOFT_DISCONNECT
* when pullup is off, set SOFT_DISCONNECT
This is especially useful when a gadget disconnection is initiated but
no board_usb_cleanup() is called.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The patch fixes the following error when updating a BSH SMM S2 board:
3:72>Start Cmd:FB[-t 8000]: ucmd nand write ${loadaddr} nanddtb ${filesize}
3:72>Okay (0.023s)
3:72>Start Cmd:FB: reboot
3:72>Fail Bulk(R):LIBUSB_ERROR_IO(0s)
The "fastboot reboot" command detaches the USB when it still needs to be
used. So let's detach the USB just before the reset.
CC: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Fixes: 5f7e01e9d5 ("usb: gadget: fastboot: detach usb on reboot commands")
Suggested-by: Michael Trimarchi <michael@amarulasolutions.com>
Co-developed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
The main issue the driver addresses is that a USB hub needs to be
powered before it can be discovered. This is often solved by using
"regulator-always-on".
This driver is inspired by the Linux v6.1 driver. It only enables (or
disables) the hub vdd (3v3) supply, so it can be enumerated.
Scanning of the device tree is done in a similar manner to the sandbox,
by the usb-uclass. DT part looks like:
&usbh_ehci {
...
#address-cells = <1>;
#size-cells = <0>;
hub@1 {
compatible = "usb424,2514";
reg = <1>;
vdd-supply = <&v3v3>;
};
};
When the bus gets probed, the driver is automatically probed/removed from
the bus tree, as an example on stm32:
STM32MP> usb start
starting USB...
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ + ] ehci_generic | |-- usb@5800d000
usb_hub 0 [ + ] usb_onboard_hub | | `-- hub@1
usb_hub 1 [ + ] usb_hub | | `-- usb_hub
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Much of the fastboot code predates the introduction of Kconfig and
has quite a few #ifdefs in it which is unnecessary now that we can use
IS_ENABLED() et al.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3l
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two callers of image_source_script specify an image name. However, both
use the deprecated @ syntax, indicating that they have not been updated
in a while. If CONFIG_FIT_SIGNATURE is enabled, we will reject such
names outright. Back in commit 152576a598 ("stm32mp: stm32prog: handle
U-Boot script in flashlayout alternate"), we even renamed one of the
nodes. Instead of hard-coding a script image name, just use the default
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Perform simple renames of:
CONFIG_MXC_USB_FLAGS to CFG_MXC_USB_FLAGS
CONFIG_MXC_USB_PORT to CFG_MXC_USB_PORT
CONFIG_MXC_USB_PORTSC to CFG_MXC_USB_PORTSC
Signed-off-by: Tom Rini <trini@konsulko.com>
This define is not enabled by the only platform which currently enables
the legacy option of CONFIG_USB_DEVICE. We can drop this code.
Signed-off-by: Tom Rini <trini@konsulko.com>
As it's no longer possible to have !DM_USB set, we can remove these
dependencies.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prevent access to arbitrary memory locations in gen_ndis_set_resp
via manipulation of buf->InformationBufferOffset. Original
implementation permits manipulation of InformationBufferOffset to
exploit OID_GEN_CURRENT_PACKET_FILTER to set arbitrary memory contents
within a 32byte offset as the devices packet filter. The packet filter
value may be next retrieved using gen_ndis_query_resp so it is possible
to extract specific memory regions two bytes a time.
The rndis_query_response was not modified as neither the buffer offset
nor length passed to gen_ndis_query_resp is used.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
