Commit graph

445 commits

Author SHA1 Message Date
Chen-Yu Tsai
533f2433ff sunxi: Add Libre Computer ALL-H5-CC H5 board
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

  - Gigabit Ethernet via external RTL8211E Ethernet PHY
  - 16 MiB SPI NOR flash memory
  - PoE tap header
  - Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:13:55 +05:30
Chen-Yu Tsai
986b5e8c4a sunxi: Add Libre Computer ALL-H3-IT H5 board
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

  - H2, H3, or H5 SoC from Allwinner
  - 2 DDR3 DRAM chips
  - Realtek RTL8821CU based WiFi module
  - 128 Mbit SPI-NOR flash
  - micro-SD card slot
  - micro HDMI video output
  - FPC connector for camera sensor module
  - generic Raspberri-Pi style 40 pin GPIO header
  - additional pin headers for extra USB host ports, ananlog audio and
    IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:09:47 +05:30
Simon Glass
29a4a9f105 common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-24 23:06:49 +05:30
Simon Glass
91527c9a30 common: Move RAM-sizing functions to init.h
These functions relate to memory init so move them into the init
header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-24 23:06:49 +05:30
Diego Rondini
e7c15b7ab8 sun8i: h3: Support H3 variant of Orange Pi Zero Plus 2
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.

H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply

Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.

Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-18 20:14:16 +05:30
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Simon Glass
3db7110857 crc32: Use the crc.h header for crc functions
Drop inclusion of crc.h in common.h and use the correct header directly
instead.

With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:08 -05:00
Sunil Mohan Adapa
4ed293ae79 arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.

commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")

This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.

Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 14:15:49 +05:30
Maxime Ripard
9bd9b2bcbe MAINTAINERS: Update my email address
I'm not at bootlin anymore, and my mail address doesn't work any longer.

Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-06 15:20:53 -04:00
Simon Glass
f3998fdc4d env: Rename environment.h to env_internal.h
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.

Rename this file and add a comment at the top to indicate its internal
nature.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-11 19:27:31 -04:00
Simon Glass
c7694dd483 env: Move env_set_hex() to env.h
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Marcus Cooper
a9e19b8ff7 sun8i: h3: Add support for the Beelink-x2 STB
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.

Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-15 12:25:32 +05:30
Jonas Smedegaard
997b857ae3 sun50i: a64: Add Olimex A64-Teres-I board initial support
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)

Works:
- i2C
- MMC/SD
- PWM backlight

Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.

This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).

Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)

Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.

config and .dtsi file are adapted from pinebook files.

Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09 00:44:13 +05:30
Clément Péron
517ee64205 arm: dts: h6: Add Beelink GS1 initial support
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)

Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-18 22:14:34 +05:30
Andre Przywara
f8c8669760 sunxi: update SATA driver to always use DM_SCSI
It seems like the Allwinner SATA driver is already quite capable of
using the driver model, so we can force this on all boards and can
remove support for a non-DM_SCSI build.
This removes the warning about boards with SATA ports not being
DM_SCSI compliant.

It also takes the opportunity to move the driver out of the board/sunxi
directory to join its siblings in drivers/ata, and to make it a proper
Kconfig citizen.

The board defconfigs stay untouched.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: select DM_SCSI separately]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 14:34:45 +05:30
Jagan Teki
cbb9cdc7aa board: sunxi: Add R40 sata compatible
Add sata compatible for R40.

Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 14:34:45 +05:30
Jagan Teki
99a8a3114f board: sunxi: gmac: Remove Ethernet clock and reset
Since Ethernet clock and reset is now handling via
CLK and RESET frameworks via driver API's remove
explicit ccm writes.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-16 16:29:01 +05:30
Tom Rini
216800acf1 Merge branch 'master' of git://git.denx.de/u-boot-spi
Conflicts:
	arch/arm/dts/armada-385-amc.dts
	arch/arm/dts/armada-xp-theadorable.dts
	arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-14 00:03:06 -04:00
Jagan Teki
59aea29a31 MAINTAINERS: Change Jagan's email address
Missed few mails from openedev, since most of the day I look at
amarulasolutions mail so update the same.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 18:47:16 +05:30
Jagan Teki
1692c73ccb sun50i: a64: Add Oceanic 5205 5inMFD initial support
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply

Linux commit details about the sun50i-a64-oceanic-5205-5inmfd.dts sync:
"arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support"
(sha1: 00f7980a3bd53d12abc34f68146a8eed0e894248)

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-10 15:25:38 +05:30
Chen-Yu Tsai
da95ed58c4 sunxi: Add Bananapi M2+ H5 board
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.

Add the following to support it:

  - device tree file: synced from Linux v5.0-rc1,
  - defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
	       family and default device tree file name changed
  - MAINTAINERS entry

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-18 14:46:53 +05:30
Chen-Yu Tsai
268ae65487 sunxi: Rename Sinovoip BPI M2 Plus to Bananapi M2 Plus H3
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.

To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.

Also add myself as one of the board maintainers.

As the device tree files were already correctly named, they do not
require any changes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: removed unneeded message from commit body]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-18 14:44:06 +05:30
Andre Przywara
a7ae159978 sunxi: board: do MMC pinmux setup for DM_MMC builds
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.

However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.

When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.

Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-29 23:46:14 +05:30
Aleksandr Aleksandrov
7d659573ce board: sun50i-h5: Add Emlid Neutis N5 support
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board

Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18 22:19:08 +05:30
Stefan Mavrodiev
da1ae5905e sunxi: board: Add i2c initialization for sun50i
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.

This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.

Tested with A64-SOM204 board.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-01-18 22:19:08 +05:30
From: Karl Palsson
44c214dc27 Revert "sunxi: board: Print error after power initialization fails"
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.

Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.

This reverts commit a8011eb84d.

Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-30 00:57:17 +05:30
Tom Rini
48d299a799 Merge branch 'master' of git://git.denx.de/u-boot-usb
- DWC3 and UDC cleanup
2018-12-10 07:15:12 -05:00
Philipp Tomsich
a740ee913e lib: merge CRC16-CCITT into u-boot/crc.h
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure.  Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-08 20:18:32 -05:00
Andre Przywara
8a6121ea07 sunxi: update README.sunxi64
Now that the Allwinner port in the official mainline ARM Trusted
Firmware repository has reached feature parity with the "legacy" ATF
port, let's use the opportunity to update the Allwinner 64-bit build
instructions. This changes:
- Update ATF build instructions to use the mainline repo.
- Add quick command lines for TL;DR people.
- Mention Allwinner H6 build target.
- Mention pre-built FEL binaries.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-07 22:30:19 +05:30
Olliver Schinagl
a8011eb84d sunxi: board: Print error after power initialization fails
Currently during init, we enable all power, then enable the dram and
after that check whether there was an error during power-up.

This makes little sense, we should enable power and then check if power
was brought up properly before we continue to initialize other things.

This patch moves the DRAM init after the power failure check.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Jean-Jacques Hiblot
0131162439 dm: usb: create a new UCLASS ID for USB gadget devices
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.

Also move the generic DM code for USB gadgets in a separate file for
clarity.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Tom Rini
ad890cace3 sunxi: Update MAINTAINERS file for recent boards
Add entries for the pine64-lts and pinebook configs.

Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-16 16:52:01 -05:00
Jagan Teki
e6b16e7852 board: allwinner: sun50i-h6: Add Orangepi Lite2 support
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13 22:13:09 +05:30
Vasily Khoruzhick
31a4ac4d79 sun50i: A64: add support for R_I2C controller
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.

Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:09:10 +05:30
Jun Nie
7bb0d212f2 sunxi: add support for Banana Pi M2 Zero board
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-10-31 12:13:02 +05:30
Andre Przywara
5776610e9e sunxi: store DRAM size in SPL header
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.

As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.

Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Andre Przywara
cff5c13849 sunxi: board.c: refactor SPL header checks
So far we have two users which want to look at the SPL header. We will
get more in the future.
Refactor the existing SPL header checks into a common function, to
simplify reusing the code.
Now that this is easy, add proper version checks to the DT name parsing.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Andre Przywara
55d481d201 sunxi: Extend SPL header versioning
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.

Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.

[1] https://semver.org

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Icenowy Zheng
c6c2c85e4b sunxi: disable Pine A64 model detection code on other boards
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.

Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.

On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:07 +05:30
Priit Laes
df4ad94d05 sunxi: docs: Mention CONFIG_NAND requirement
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Priit Laes
297963f5b5 sunxi: Fix typos of spelling Allwinner
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Jagan Teki
d8024074e4 board: sunxi: Remove unused local variables
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-20 18:10:43 +05:30
Jagan Teki
89a897fc4d board: sun50i: h6: Add OrangePi One Plus initial support
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-07-31 20:50:01 +05:30
Icenowy Zheng
a8407b5642 sunxi: add support for Pine H64 board
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.

Add support for it.

The device tree is from Linux next-20180720.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
42956f1b85 sunxi: add MMC support for H6
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.

Add MMC support for H6. EMCE support is not added yet.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
0a21fdd62b sunxi: change ATF position for H6
H6 has different SRAM A2 address, so the ATF load address is also
different.

Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Hauke Mehrtens
76d69eb01d sun50i: h5: Add initial Orange Pi Zero Plus support
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.

H5 Orangepi Zero Plus has
 - Quad-core Cortex-A53
 - 512MB DDR3
 - micrSD slot
 - 16MBit SPI Nor flash
 - Debug TTL UART
 - 1GBit/s Ethernet (RTL8211E)
 - Wifi (RTL8189FTV)
 - USB 2.0 Host
 - USB 2.0 OTG + power supply

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Hauke Mehrtens
a6580dfd46 sun8i: h2: Add initial Orange Pi R1 support
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.

H2+ Orange Pi R1 has
 - Quad-core Cortex-A7
 - 256MB DDR3
 - micrSD slot
 - 128MBit SPI Nor flash
 - Debug TTL UART
 - 100MBit/s Ethernet (H2+)
 - 100MBit/s Ethernet (RTL8152B)
 - Wifi (RTL8189ETV)
 - USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Jagan Teki
2e8dbe14e7 board: sun50i: Add Amarula A64-Relic initial support
Amarula A64-Relic is A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 1GB DDR3 RAM
- 8GB eMMC
- AP6330 Wifi/BLE
- MIPI-DSI
- CSI: OV5640 sensor
- USB OTG
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-06-04 18:09:25 +05:30
Jagan Teki
f5871a66fd sunxi: Drop legacy usb_phy.c
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30