At present this is disabled, but it should work so long as the kernel does
not need EFI services. Enable it and add a note about remaining work.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only the backspace key is supported in U-Boot, when running as
an EFI app. Add support for arrows, home and end as well, to make the CLI
more friendly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When starting the app, locate all block devices and make them available
to U-Boot. This allows listing partitions and accessing files in
filesystems.
EFI also has the concept of 'disks', meaning boot media. For now, this
is not obviously useful in U-Boot, but add code to at least locate these.
This can be expanded later as needed.
We cannot use printf() in the early stub or app since it is not compiled
in
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is needed to show unicode strings. Enable this code in the app.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add some long overdue instructions for building and installing U-Boot on
Allwinner SoC based boards.
This describes the building process, including TF-A and crust, plus
installation to SD card, eMMC and SPI flash, both from Linux and U-Boot
itself. Also describe FEL booting.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
-----BEGIN PGP SIGNATURE-----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=VFOg
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-01-rc4-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc4-4
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
- Merge a large number of CONFIG migration patches. Most of these are
taking existing migrations and re-running them. A few of these needed
additional minor conversions done first, so that more complex
dependencies could be expressed. In the end we now have CI jobs to
ensure that no migrated symbols are used in board config header files.
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a number of symbols that are never defined, only referenced in
code imported from the Linux kernel or similar. Drop them from the list.
Signed-off-by: Tom Rini <trini@konsulko.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all symbols that exist in Kconfig no longer also have boards
setting them in the board config.h file, add a CI test to catch new
instances of this, and fail.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
The values CONFIG_SYS_CLK_FREQ_C100 and CONFIG_SYS_CLK_FREQ_C110 are
only used in one place and not changed by the board config file. Move
these out of the CONFIG namespace and in to the CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
