Commit graph

1131 commits

Author SHA1 Message Date
Sandeep Paulraj
57418d2139 Davinci MMCSD Support
Added support for MMC/SD cards for Davinci.  This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.

Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:44 +01:00
Roy Zang
3b4456ec39 fsl_esdhc: Add the workaround for erratum ESDHC135 (enable on P4080)
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.

Clear these bits out when we read HOSTCAPBLT.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Jerry Huang
d621da0066 fsl_esdhc: Add the workaround for erratum ESDHC111 (enable on P4080)
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Chenhui Zhao
a6da8b8195 fsl_esdhc: Fix esdhc disabled problem on some platforms
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.

Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.

Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Li Yang
030955c2ca fsl_esdhc: Fix the voltage validation process
The current code use all the voltage range support by the host
controller to do the validation.  This will cause problem when
the host supports Low Voltage Range.  Change the validation
voltage to be based on board setup.

Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:24 +01:00
Jerry Huang
63786d299d fsl_esdhc: Fix max clock frequency
The max clock of MMC is 52MHz

Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:24 +01:00
Jerry Huang
4a6ee172c3 fsl_esdhc: Use mmc_set_clock to set initial speed
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.

Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:21 +01:00
P.V.Suresh
2c1764efc2 fsl_esdhc: Set the eSHDC DMACTL[SNOOP] bit after resetting the controller
eSDHC host controller reset results in clearing of snoop bit also.
This patch sets the SNOOP bit after the completion of host controller reset.
Without this patch mmc reads are not consistent.

Signed-off-by: P.V.Suresh <pala@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13 09:32:16 -06:00
Reinhard Meyer
2aed9d14cc AT91: gen_atmel_mci.c: fix bug when Slot B is used
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-12-07 16:36:39 +01:00
Nishanth Menon
eb9a28f699 mmc: omap: timeout counter fix
Having a loop with a counter is no timing guarentee for timing
accuracy or compiler optimizations. For e.g. the same loop counter
which runs when the MPU is running at 600MHz will timeout in around
half the time when running at 1GHz. or the example where GCC 4.5
compiles with different optimization compared to GCC 4.4. use timer
to keep track of time elapse and we use an emperical number - 1sec
for a worst case timeout.  This should never happen, and is adequate
imaginary condition for us to fail with timeout.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:27:37 -05:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Alagu Sankar
4a1a06bc8b mmc: Add multi-block read support to the generic mmc driver
This patch adds multi-block read support for the generic MMC
driver. Large reads are broken into chunks of 65535 blocks to
ensure that the code works with controllers having a 16 bit block counter.

This patch results in a significant performance improvement.

Time to read a 45 MB file went from 36 seconds to 9 seconds on Overo

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:25 -04:00
Steve Sakoman
def412b661 mmc: Clean up generic mmc driver multi-block write functions
The current mmc write implementation is type ulong, but returns int values.
Some of the printf's are terminated with /n/r, one has none.

This patch fixes these issues and also removes some unnecessary local
variables.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:21 -04:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Lei Wen
0158126e25 mmc: seperate block number into small parts for multi-write cmd
Constraint the mmc framework to only send no more than 65535
blocks in one go during the multi-write command. This constraint
comes due to the limitation of 16bit width block counter register
at some hardware.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-27 20:39:33 +02:00
Marek Vasut
3ba8bf7c6d PXA: pxa-regs.h cleanup
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:46:22 +02:00
Jaehoon Chung
1727e21698 s5p_mmc: support 8-bit bus width
This Patch do support 8-bit bus width for s5p
So we add parameter for bus_width (in s5p_mmc_init(), s5p_mmc_initialize())
If want to use 8-bit bus width, only change (0, 8) instead of (0, 4).

 Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
 Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
 Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-10-19 11:34:54 +09:00
Sukumar Ghorai
de941241a0 ARMV7: OMAP: Add new mmc driver compatible with CONFIG_GENERIC_MMC
OMAP boards currently use a legacy mmc driver. This patch adds a new
mmc driver which will work with the generic mmc driver in u-boot.

This new driver will work with both OMAP3 and OMAP4 boards.

This patch does not remove the old driver.  It should remain in the
tree until all boards that use it switch to the new driver.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
2010-10-17 20:14:10 +02:00
Sukumar Ghorai
d23e2c09a7 MMC: Fix for capacity calculation on eMMC
The current mmc driver returns erroneous capacity information for
  eMMC.  The capacity of eMMC devices is available only in the ext-CSD
  register.  This patch add code to read the ext-CDSD register and
  correctly calculate eMMC capacity.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
2010-10-17 20:14:06 +02:00
Mike Frysinger
6815f540db Blackfin: bfin_sdh: clean up send_cmd
Simplify the command setup and status checking steps, and add a proper
timeout to the status polling code to avoid possible infinite hangs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:37 -04:00
Wolfgang Denk
fe64fd4238 mmc: fix compiler warnings
Commit d2bf29e3 caused a number of compiler warnings:

mmc.c: In function 'mmc_bwrite':
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
mmc.c: In function 'mmc_bread':
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
2010-09-19 12:30:54 +02:00
Lei Wen
d2bf29e399 mmc: add boundary check for mmc operation
Signed-off-by: Lei Wen <leiwen@marvell.com>
2010-09-18 23:46:24 +02:00
Wolfgang Denk
cf64fda38e Merge branch 'at91' of git://git.denx.de/u-boot-atmel 2010-09-08 00:42:00 +02:00
Wolfgang Denk
09b4a9cf40 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-09-08 00:03:22 +02:00
Reinhard Meyer
1592ef8596 AT91: MCI: add SD/MMC driver using mmc framework
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-09-03 11:19:01 +02:00
Minkyu Kang
d93d0f0cfe S5P: Use accessor functions instead of SoC specific defines to access the base address
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-08-17 11:38:19 +09:00
Grazvydas Ignotas
dc41b8bf3d mmc: omap3: fix block read function
The OMAP3 block read function is not following API and always returning
1 instead of read block count, fix it. Also to simplify code, merge it
with with a helper function, which was only called from the block read
function.

After this patch ext2 filesystem can be used properly.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-12 13:50:25 -04:00
Grazvydas Ignotas
8bbf4307c7 mmc: omap3: make local symbols static
Make driver local variables and functions static and
remove them from the arch header.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-12 13:50:19 -04:00
Minkyu Kang
6a69e11a79 S5P: mmc: use the standard debug macro
Use the standard debug macro instead of the costom macro

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
2010-08-10 13:42:23 +09:00
Wolfgang Denk
9efac4a1eb Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-08-04 00:35:10 +02:00
Minkyu Kang
5000284872 S5P: support mmc driver
This patch adds support mmc driver for s5p SoC

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-08-03 10:18:15 +09:00
Wolfgang Denk
93502a5e0a Merge branch 'master' of ../master 2010-07-15 22:48:46 +02:00
Mike Frysinger
a87589fcf9 Blackfin: bfin_sdh: convert to portmux framework
Rather than bang MMRs directly, use the new portmux framework to handle
the details.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13 17:50:49 -04:00
Steve Sakoman
89716964d9 mmc: add function prototype for mmc_set_dev in mmc.h
this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV

the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:32 -04:00
Steve Sakoman
bec3dc7599 ARMV7: Restructure OMAP mmc driver to allow code sharing between OMAP3 and OMAP4
The architecture independent header is moved to drivers/mmc, and the architecture
dependent headers reside in asm/arch-omap3 and asm/arch-omap4

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:05 -04:00
Steve Sakoman
8f22327a66 OMAP: mmc: add support for second and third mmc channels
This patch adds support for the second and third mmc channels on OMAP3
processors

Boards wishing to use this feature should define CONFIG_SYS_MMC_SET_DEV
in the board config

Tested on Overo

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:49 -04:00
Marek Vasut
43c15d3dd5 PXA: PXAMMC: Add Monahans support
This patch enables PXAMCI support on PXA3xx CPUs. This patch only enables MMC1
though, MMC2 and PXA31x MMC3 will need further patch to be operational.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-06-13 13:39:11 +02:00
Marek Vasut
55429a0323 PXA: PXAMMC: Drop different delays for PXA27X
In case the delays were set to 10000, the MMC card on PXA27X boards (and PXA3xx
boards) didn't initialize on first try. Increasing the delays and leaving just
those for PXA25x and 26x (that is 200000) fixes this problem.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-06-13 13:39:11 +02:00
Wolfgang Denk
7b43db9211 drivers/mmc/fsl_esdhc.c: fix compiler warnings
Commit 77c1458d caused the following compiler warnings:

fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2010-05-15 19:47:17 +02:00
Dipen Dudhat
77c1458d13 ppc/85xx: PIO Support for FSL eSDHC Controller Driver
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.

Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
2010-04-23 21:02:30 -05:00
Roy Zang
ab467c512e fsl_esdhc: Only modify the field we are changing in WML
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Jerry Huang
48bb3bb5ac fsl_esdhc: Add function to reset the eSDHC controller
To support multiple block read command we must set abort or use auto
CMD12.  If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Kumar Gala
cc4d122658 fsl_esdhc: Always stop clock before changing frequency
We need to stop the clocks on 83xx/85xx as well as imx.  No need to make
this code conditional to just imx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-04-07 00:01:11 -05:00
Stefano Babic
99c006a320 mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessors
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-21 22:22:52 +01:00
Wolfgang Denk
8c4444ff5e Fix memory leak in mmc_read()
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.

Reported-by: Quentin Armitage <Quentin@Armitage.org.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-11 23:35:43 +01:00
Stefano Babic
c67bee1460 fsl_esdhc: add support for mx51 processor
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic
11fdade294 MMC: add weak function to detect MMC/SD card
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic
250de12bc2 mmc: check correctness of the voltage mask in ocr
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Cliff Cai
e54c820991 Blackfin: convert bfin_sdh to generic mmc
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Vaibhav Hiremath
7c15121f40 omap3_mmc: Encapsulate twl4030 under option CONFIG_TWL4030_POWER
Fixes the build/compilation error if we try to re-use the omap3_mmc code
without TWL4030_POWER.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
2009-11-27 16:26:18 -06:00
Dirk Behme
9de0212bd7 OMAP3 MMC: Fix warning dereferencing type-punned pointer
Fix warning
Dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Steve Sakoman <sakoman@gmail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
2009-10-13 06:17:36 -05:00
Wolfgang Denk
53cc18c71b Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-10 10:38:34 +02:00
Ilya Yanok
ba3dbaf281 mxc-mmc: sdhc host driver for MX2 and MX3 proccessor
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-08-09 23:47:38 +02:00
Tom Rix
fccc0fcaaa OMAP3 Move twl4030 mmc function
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.

twl4030_mmc_config initializes the twl4030 power setting to
the mmc device.  Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.

The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format

twl4030_power_<device>_<action>

In this case the suffix is mmc_init so
device : mmc
action : init

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:43 +02:00
Ilya Yanok
b86b85e261 mmc: set bus width to 1 and clock to minimum early during initialization
We need to switch back to 1-bit before initialization or SD 2.0 cards
will fail to send SCR if we've switched to 4-bit already.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-07-19 22:07:29 +02:00
Anton Vorontsov
b33433a63f fsl_esdhc: Add device tree fixups
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.

The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-16 22:24:06 +02:00
Yauhen Kharuzhy
4e3d89ba94 mmc: Fix decoding of SCR & function switch data on little-endian machines
SCR & switch data are read from card as big-endian words and should be
converted to CPU byte order.

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-06-02 17:20:04 -05:00
Yauhen Kharuzhy
f33cb34b39 mmc: Remove return from mmc_init for non SD 2.0 compatible cards.
Cards which are not compatible with SD 2.0 standard, may return response
for CMD8 command, but it will be invalid in terms of SD 2.0. We should
accept this case as admissible, just like Linux does.

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-06-02 17:19:07 -05:00
Rabin Vincent
998be3dd59 mmc: drop unnecessary casts
Now that response is a uint, we can drop all the casts.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:57 -05:00
Rabin Vincent
0b453ffe28 mmc: fix response decoding on little endian
The mmc code defines the response as an array of chars.  However, it
access the response bytes both as (i) an array of four uints (with
casts) and (ii) as individual chars.  The former case is used more
often, including by the driver when it assigns the response.

The char-wise accesses are broken on little endian systems because they
assume that the bytes in the uints are in big endian byte order.

This patch fixes this by changing the response to be an array of four
uints and replacing the char-wise accesses with equivalent uint-wise
accesses.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:57 -05:00
Rabin Vincent
9b1f942c09 mmc: use lldiv to fix arm eabi build
The generic MMC core uses direct long long divisions, which do not build
with ARM EABI toolchains.  Use lldiv() instead, which works everywhere.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:56 -05:00
Rabin Vincent
e85649c7e6 mmc: check find_mmc_device return value
find_mmc_device returns NULL if an invalid device number is specified.
Check for this to avoid dereferencing NULL pointers.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:56 -05:00
Peter Tyser
f9a109b3ad Replace __attribute references with __attribute__
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute.  This change is only asthetic and should not
affect functionality.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-28 01:01:39 +02:00
Mike Frysinger
d3c38d96b9 Blackfin: convert bfin_sdh to legacy mmc
The Blackfin SDH controller is still using the legacy framework, so update
the driver to use the renamed functions.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:42:05 -04:00
Dirk Behme
aba45c85b2 OMAP3: Clean up MMC code
Clean up OMAP3 MMC code:

* Convert register access to struct & readx/writex style
* Replace hardcode values by macros
* Remove macro defined twice

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Wolfgang Denk
09fee8e867 Coding Style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22 01:19:52 +01:00
Tom Rix
e3ba7f137c ARM:PXA Use new definitions in mmc.h
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Andy Fleming
682beeac34 Reduce the scope of PXA's mmc_read/mmc_write/mmc_bread functions
These names are being taken over by the new MMC framework.  Hopefuly
the PXA can be easily ported, and these functions will go away entirely.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Jean-Christophe PLAGNIOL-VILLARD
b03d92e558 pxa: move mmc drivers to drivers/mmc
introduce new macro CONFIG_PXA_MMC to activate it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Tom Rix
e5e88c3614 ARM:OMAP3 Change mmc_init to mmc_legacy_init
omap3_mmc.c was changed to define mmc_legacy_init.
Remove unused functions.

Compile tested on all arm
Runtime tested on Zoom1.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-02-19 23:50:33 +01:00
Andy Fleming
50586ef24e Add support for the Freescale eSDHC found on 8379 and 8536 SoCs
This uses the new MMC framework

Some contributions by Dave Liu <daveliu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:42 -06:00
Andy Fleming
272cc70b21 Add MMC Framework
Here's a new framework (based roughly off the linux one) for managing
MMC controllers.  It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.

This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)

Some of this code was contributed by Dave Liu <daveliu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:41 -06:00
Andy Fleming
abb5466ccf Convert mmc_init to mmc_legacy_init
This is to get it out of the way of incoming MMC framework

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:40 -06:00
Andy Fleming
b2e2ed0233 Eliminate support for using MMC as memory
MMC cards are not memory, so we stop treating them that way.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:40 -06:00
Cliff Cai
716ebf436c Blackfin: add driver for on-chip MMC/SD controller
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02 12:27:18 -05:00
Dirk Behme
b1c3bf99fb OMAP3: Add MMC support
Add MMC support.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24 17:51:22 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Stefan Roese
f2302d4430 Fix merge problems
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:05:38 +02:00
Haavard Skinnemoen
c3bf1ad7ba mmc: Move atmel_mci driver into drivers/mmc
This makes it easier to use the driver on other platforms.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-10 00:05:52 +02:00
Haavard Skinnemoen
5ce13051a4 Create drivers/mmc subdirectory
In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-10 00:02:36 +02:00