Tegra uses built in Power Management Controller (PMC) to perform
CPU reset. Code to perform this was located in mach-tegra, so lest
create DM driver to handle this.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dev->driver_data will carry the tail of ldo if there is a number and
if there is no number it will be an error code, anyway it will not be
zero. This results in a wrong ldo regulator detection.
To avoid this check for non-numerical ldo first and then manipulate
dev->driver_data.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing PALMAS PMIC driver is fully compatible with TI TPS65913
PMIC found in many Tegra 4 devices, like Tegra Note 7 and ASUS
TF701T. TPS65913 shares same structure of regulators like TPS659038
so data can be reused.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # NVIDIA Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Default-tap and default-trim values are used for eMMC setup
mostly on T114+ devices. As for now, those values are hardcoded
for T210 and ignored for all other Tegra generations. Fix this
by passing tap and trim values from dts.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
on Peach-pi console every key press is echoed with message
'cros_ec_command: Returned status 1'
this is not proper fix, just hack to disable this message
Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2024.01-rc2
- nuvoton: support standard/fast/fast plus mode
- bootcount: remove legacy i2c driver and implement
DM based version
Bugfixes:
- designware_i2c: adjust timing calculation
SPL probing failed on the StarFive VisionFive 2 board
Heinrich fixed this, by syncing timing calculation with
linux implementation.
+ CI: Use OpenSBI 1.3.1 release for testing
+ riscv: Support resume after exception
+ rng: Support RNG provided by RISC-V Zkr ISA extension
+ board: starfive VF2: Support jtag
+ board: starfive VF2: Support TRNG driver
+ board: sifive unmatched: Move kernel load address
In line with changes elsewhere, drop inclusion of the common header.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add STGCLK_SEC_HCLK and STGCLK_SEC_MISCAHB clocks for JH7110 TRNG
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This contains several fixes for the clock core.
-----BEGIN PGP SIGNATURE-----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=QToO
-----END PGP SIGNATURE-----
Merge tag 'clk-2024.01-rc2' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for 2024.01-rc2
This contains several fixes for the clock core.
In clk_enable()/clk_disable() functions, when CCF is activated,
we must pass a private clk struct to enable()/disable() ops functions.
Otherwise, the use of a container_of() construction within these ops
should be banned. Because passing a non-private clk struct to
container_of() results in an out of range error.
At the moment, clk-mux, clk-fixed-factor, clk-gate and possibly other
clocks use container_of() in their enable()/disable() functions.
Therefore, for these functions to work correclty, private clk struct
must be passed.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230905221649.3577929-1-bigunclemax@gmail.com
The second parameter for clk_release_all is used as an unsigned
(which makes sense) but the function prototype declares it as an int.
This causes warnings/error like such below:
include/clk.h:422:48: error: conversion to ‘int’ from ‘unsigned int’ may change the sign of the result [-Werror=sign-conversion]
422 | return clk_release_all(bulk->clks, bulk->count);
To fix this, changed the type of the count to `unsigned int`
Fixes: 82a8a669b4 ("clk: add clk_release_all()")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230619104752.278500-1-eugen.hristev@collabora.com
In commit 5c5992cb90 ("clk: Add debugging for return values"), a
temporary storage variable was added around the ops->get_rate() call
inside clk_get_rate(), so that the result could be passed through
log_ret.
This temporary variable was declared as an int, yet when we look in
struct clk_ops, we can see this needs to be a ulong:
ulong (*get_rate)(struct clk *clk);
This was resulting in a signed to unsigned casting error on our
builds, where a clock value of 0xABCDABCD was being incorrectly cast
to 0xFFFFFFFFABCDABCD.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230515195005.1961495-1-nathan.morrison@timesys.com
Compiling sandbox_defconfig with CONFIG_BOOTSTD=n fails:
/usr/bin/ld: drivers/mtd/spi/sf_bootdev.o:
in function `sf_get_bootflow':
/drivers/mtd/spi/sf_bootdev.c:43:(.text+0x96):
undefined reference to `bootmeth_set_bootflow'
Add the missing Kconfig dependency.
Fixes: Fixes: 0c1f4a9fb1 ("bootstd: Add a SPI flash bootdev")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As noted in commit 3a6383207b ("mmc: sdhci: add the quirk for broken
r1b response"), some MMC controllers don't always set the transfer
complete bit with R1b responses.
According to the SD Host Controller Simplified Specification v4.20,
> In the case of a command pairing with response-with-busy[, Transfer
> Complete] is set when busy is de-asserted. Refer to DAT Line Active
> and Command Inhibit (DAT) in the Present State register.
By polling the DAT Line Active bit in the present state register, we can
detect when we are no longer busy, without waiting for a long timeout.
This results in much faster reads/writes on buggy controllers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
dm_pci_map_bar() return a value of (void *) already, hence no need
to cast it again before assigning to host->ioaddr.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_bind() in mmc-uclass.c calls blk_create_devicef() which is
defined in blk-uclass.c, so SPL_BLK is required by SPL_DM_MMC.
Implicitly select SPL_BLK for SPL_DM_MMC.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
PLL calibration needs to be enabled when operating in non fractional
mode. Add the sequence to do a fast calibration when using PLL
in this mode.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Add support for exposing the whole mmc device by setting the 'size'
parameter to 0. This can be useful in case it is not clear what the
total device size is up front. Update the documentation accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20231029223740.284149-1-marex@denx.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This adds a generic I2C bootcounter adhering to driver model to replace
the previously removed legacy implementation.
There is no change in functionality, it can be used on any I2C device.
The device tree configuration may look like this for example:
bootcount {
compatible = "u-boot,bootcount-i2c";
i2cbcdev = <&i2c_rtc>;
offset = <0x11>;
};
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This new function enhances the i2c_get_chip*() toolbox by implementing a
variant that does not require a chip_addr. Instead, the desired device
is pointed to by a phandle.
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
The legacy I2C bootcounter will hereby be removed and eventually
be replaced by a driver model implementation in the follow-up commit.
The legacy driver has the following drawbacks:
- It's not adhering to the driver model
- Settings are grabbed from Kconfig rather than device tree
- i2c_{read,write} are being used instead of dm_i2c_{read,write}
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
In SPL probing of the designware_i2c device on the StarFive VisionFive 2
board fails with
dw_i2c: mode 0, ic_clk 1000000, speed 100000,
period 10 rise 1 fall 1 tlow 5 thigh 4 spk 0
dw_i2c: bad counts. hcnt = -4 lcnt = 4
device_probe: i2c@12050000 failed to probe -22
When changing the offset for the high phase from 7 to 3 the device is
probed correctly. This now matches the value from the Linux driver.
Without this fix the memory size of the StarFive VisionFive 2 board cannot
be read from EEPROM.
Fixes: e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
first version is only support standard mode.
remove this judgment to support standard/fast/fast plus mode.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Changes for v2:
- add commit message
Reviewed-by: Heiko Schocher <hs@denx.de>
To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.
Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>
In current vexpress_config_probe code, it sets the uclass private data
directly. This will cause one compilation error:
drivers/misc/vexpress_config.c:114:27: error: lvalue required as left operand of assignment
114 | dev_get_uclass_priv(dev) = priv;
| ^
In this patch we set the uclass private data through struct member
.priv_auto, and this compilation error disappears.
Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=gvDs
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-27102023' of https://source.denx.de/u-boot/custodians/u-boot-tpm
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
Add A1 SPIFC driver from Linux. Slightly modified to use u-boot driver
framework and accommodate to lack of ioread32_rep/iowrite32_rep.
Based on Linux version 6.6-rc4
Signed-off-by: Igor Prusov <IVPrusov@sberdevices.ru>
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20231024225140.366571-2-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[trini: Drop <common.h> as it's not needed]
The driver needs to support getting the PCRs in the capabilities
command. Fix various other things and support the max number
of PCRs for TPM2.
Remove the !SANDBOX dependency for EFI TCG2 as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The R-Car Gen3 SD_CLK_CTRL register does not use BIT(16) to implement
divider 1/1024, instead BIT(16) is reserved bit and divider 1/1024 is
not supported. The divider 1/1024 is specific to Socionext variant of
the IP, as is indicated by Linux commit:
0196c8db8363 ("mmc: tmio: move tmio_mmc_set_clock() to platform hook")
"
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
"
Do not set the TMIO_SD_CAP_DIV1024 on Renesas R-Car platforms even if
the IP VERSION register does exist, and indicates IP version is newer
or equal to version 1.0 . The IP version 1.0 or newer does not imply
presence of the 1/1024 divider.
Since the TMIO driver is used exactly by two supported platforms, that
is Renesas R-Car and Socionext UniPhier, it is OK to check whether the
TMIO_SD_CAP_RCAR capability is not set to identify the UniPhier platform
and add the capability only on that platform.
Fixes: 58c35b17aa ("mmc: matsushita-common: Always check controller version")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
