Commit graph

425 commits

Author SHA1 Message Date
pekon gupta
54a97d2849 board/ti/dra7xx: add support for parallel NAND
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:

  SW5.9 (GPMC_WPN)   = OFF (logic-1)
  SW5.1 (NAND_BOOTn) = ON  (logic-0) /* Active-low */
  SW5.2 (NOR_BOOTn)  = OFF (logic-1)
  SW5.3 (eMMC_BOOTn) = OFF (logic-1)
  SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations
  SW2.1 (SYSBOOT[0]) = ON  (logic-1) /* selects NAND Boot */
  SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
  SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
  SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
  SW2.5 (SYSBOOT[4]) = ON  (logic-1) /* selects NAND Boot */
  SW2.6 (SYSBOOT[5]) = ON  (logic-1) /* selects NAND Boot */
  SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
  SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */

  SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
  SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
  SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
  SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
  SW3.5 (SYSBOOT[12])= ON  (logic-1) /* device type: Addr/Data Muxed */
  SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
  SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
  SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Following changes are required in board.cfg to enable NAND on J6-EVM:
2014-08-25 10:48:12 -04:00
pekon gupta
e53ad4b445 board/ti/am43xx: add support for parallel NAND
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
  time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
  controlled by:
  (a) Statically using Jumper on connecter (J89) present on board.
  (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
      by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
      SPI2_CS0 == 0: NAND (default)
      SPI2_CS0 == 1: eMMC

am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
  Thus only one of the two can be used at a time. Selection is controlled by:
  (a) Dynamically driving following GPIO pin from software
      GPMC_A0(GPIO) == 0 NAND is selected (default)

NAND device (MT29F4G08AB) on these boards has:
 - data-width=8bits
 - blocksize=256KB
 - pagesize=4KB
 - oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-08-25 10:48:12 -04:00
pekon gupta
3df3bc1e1d board/ti/am335x: add support for beaglebone NOR Cape
This patch adds support of NOR cape[1] for both Beaglebone (white) and
Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC
chip-select[0] and accesses as external memory-mapped device.
This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device.

As GPMC chip-select[0] can be shared by multiple capes so NOR profile is
not enabled by default in boards.cfg. Following changes are required to
enable NOR cape detection when building am335x_boneblack board profile.

Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25 10:47:56 -04:00
pekon gupta
85eb0de214 board/ti/am335x: add support for beaglebone NAND cape
Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]

* How to boot from NAND using Memory Expander + NAND Cape ? *
 - Important: As BOOTSEL values are sampled only at POR, so after changing any
   setting on SW2 (DIP switch), disconnect and reconnect all board power supply
   (including mini-USB console port) to POR the beaglebone.

 - Selection of ECC scheme
  for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
  for NAND cape(b), ROM code expects BCH16_HW ecc-scheme

 - Selction of boot modes can be controlled via  DIP switch(SW2) present on
   Memory Expander cape.
   SW2[SWITCH_BOOT] == OFF  follow default boot order  MMC-> SPI -> UART -> USB
   SW2[SWITCH_BOOT] == ON   boot mode selected via DIP switch(SW2)
   So to flash NAND, first boot via MMC or other sources and then switch to
   SW2[SWITCH_BOOT]=ON to boot from NAND Cape.

 - For NAND boot following switch settings need to be followed
   SW2[ 1] = OFF  (SYSBOOT[ 0]==1: NAND boot mode selected )
   SW2[ 2] = OFF  (SYSBOOT[ 1]==1:       -- do --          )
   SW2[ 3] = ON   (SYSBOOT[ 2]==0:       -- do --          )
   SW2[ 4] = ON   (SYSBOOT[ 3]==0:       -- do --          )
   SW2[ 5] = OFF  (SYSBOOT[ 4]==1:       -- do --          )
   SW2[ 6] = OFF  (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
   SW2[ 7] = ON   (SYSBOOT[ 9]==0: ECC done by ROM  )
   SW2[ 8] = ON   (SYSBOOT[10]==0: Non Muxed device )
   SW2[ 9] = ON   (SYSBOOT[11]==0:    -- do --      )

[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module

*IMPORTANT NOTE*
As Beaglebone board shares the same config as AM335x EVM, so following
changes are required in addition to this patch for Beaglebone NAND cape.
(1) Enable NAND in am335x_beaglebone board profile
(2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because:
 -  AM335x EVM has NAND device with datawidth=8, whereas
 -  Beaglebone NAND cape has NAND device with data-width=16
2014-08-25 08:52:34 -04:00
Masahiro Yamada
62d636aa2a omap: remove omap5912osk board support
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.

Tom suggested to remove this board.

Remove also omap1510_udc.c because this is the last board
to enable it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
2014-08-21 12:01:12 -04:00
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Albert ARIBAUD
b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Hao Zhang
a906847966 board: k2e-evm: add board support
This patch adds Keystone2 k2e_evm evaluation board support.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
b1babef856 keystone: ddr3: move K2HK DDR3 configuration to a common file
It's convenient to hold configurations for DDR3 PHY and EMIF in
separate common place. This patch moves K2HK DDR3 PHY and EMIF
configuration data with different rates and memory size to a common
ddr3_cfg.c file.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
e595107ebb ARM: keystone2: move K2HK board files to common KS2 board directory
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Murali Karicheri
0bedbb8135 keystone2: add env option to do unitrd dt fixup
With latest v3.13 kernel, unitrd dt fixup is not needed. However for
older kernel versions such as v3.8/v3.10, it is needed. So to work
with both, add a u-boot env variable that can be set to do dt fixup
for older kernels.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan
3d31538625 k2hk: use common KS2_ prefix for all hardware definitions
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.

Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
4984bce41f keystone2: move cpu_to_bus() to keystone.c
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
101eec50f0 keystone2: ddr: add DDR3 PHY configs updated for PG 2.0
Add DDR3 PHY configs updated for PG 2.0
Also add DDR3A PHY reset before init for PG2.0 SoCs.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Khoronzhuk, Ivan
0b86858956 keystone: ddr3: add ddr3.h to hold ddr3 API
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Tom Rini
c4f80f5003 am335x_evm / gumstix pepper: Correct DDR settings
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers.  Upon further inspection these
had been touching reserved fields (and having no impact).  These came in
from historical bring-up code and can be discarded.  Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.

Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
2014-07-25 16:26:08 -04:00
Khoronzhuk, Ivan
c6ac7e3bdc k2hk_evm: add script to automate NAND flash process
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
2014-07-25 15:21:06 -04:00
Tom Rini
7aa5598aac tps65218/am43xx_evm: Add power framework support to TPS65218
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-07-25 15:21:06 -04:00
Mugunthan V N
4c8014b942 ARM: dra7_evm: Add Ethernet support for dra72x platform
Set the active_slave to 1 as slave 1 is pinned out in dra72x base board

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-07-25 15:21:05 -04:00
Mugunthan V N
e5ff845bff ARM: DRA7xx: Add cpsw second port pinmux
Add cpsw second slave port pinmux to use it as primary ethernet port

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-07-25 15:21:05 -04:00
Lokesh Vutla
4ec3f6e510 ARM: DRA7xx: Update the board_name env variable
Update the board_name env variable and accordingly
populate the dtb file.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-14 11:16:38 -04:00
Cooper Jr., Franklin
8038b497e7 am43xx: Tune the system to avoid DSS underflows
* This is done by limiting the ARM's bandwidth and setting DSS priority in
  the EMIF controller to ensure underflows do not occur.
2014-07-07 19:42:34 -04:00
Franklin S. Cooper Jr
2c95211167 am43xx: Update EMIF DDR3 Configuration for AM43x GP
* Boot failures have been discovered due to a combination of routing issues and
  non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
  different timings are required for alpha, beta and production boards.

Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
2014-07-07 19:42:34 -04:00
Felipe Balbi
49b633b3d3 board: ti: dra7xx: add mux data for UART3
J6 EVM can be built with UART3 as console, but currently
there's nothing muxing UART3 correctly. Likely this only
works because, based on commit log, author was only testing
with UART3 boot and - I assume - ROM code leave UART3 correctly
muxed in that case.

If we want to boot from MMC and still use UART3 as console,
then we need to mux those signals correctly.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-07 19:42:34 -04:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Felipe Balbi
403edbb94f board: ti: am43xx: enable QSPI and Gbit Ethernet on AM437x SK
AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Felipe Balbi
619ce62d2d board: ti: am43xx: add AM437x SK PHY Address
pass correct PHY Address when running on SK
so that we have working ethernet with this board
too.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Felipe Balbi
9cb9f3331b board: ti: am43xx: add support for AM43xx Starter Kit
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Felipe Balbi
d51e5aeff6 board: ti: am43xx: print unsupported board name
when porting u-boot to a new am43xx board, it
helps to know the name of the current unsupported
board so we don't have to hunt for design documents
to figure out what's written in the EEPROM.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Khoronzhuk, Ivan
909ea9aa26 ARM: keystone: aemif: move aemif driver to drivers/memory/ti-aemif.c
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-06-19 17:53:58 -04:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
Simon Glass
ad3cd07f04 ti: am335x: Fix the U-Boot binary output
This should include the hash so that image_binary_size is really at the
end of the image, and not some 300 bytes earlier.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-11 16:25:39 -04:00
Tom Rini
83bad1026b arm:am43xx: Add TPS65218 support to scale voltages up
This family is supported by the TPS65218 PMIC.  Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:16 -04:00
Tom Rini
feca6e676e am43xx: Only read the MPU frequency bits of CTRL_DEV_ATTR
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:16 -04:00
Sourav Poddar
7a5f71bc40 am43xx_evm: Add qspiboot target
The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:12 -04:00
Albert ARIBAUD
41623c91b0 arm: move exception handling out of start.S files
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:53 +02:00
Tom Rini
d0e6d34d7c am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOT
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build.  Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2014-04-17 17:24:40 -04:00
Karicheri, Muralidharan
fc9a8e8d40 keystone2: net: add keystone ethernet driver
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.

Port configurations are defined in board.c.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
2014-04-17 17:24:39 -04:00
Vitaly Andrianov
ef509b9063 k2hk: add support for k2hk SOC and EVM
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.

This patch add support for keystone architecture and k2hk evm.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
79b079f35c dra7xx_evm: Add QSPI_4 support, qspiboot build target
We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:37 -04:00
Tom Rini
ba9a6708ec am335x_evm: Make SPL_OS also check the boot_os variable for falcon mode
We use the same variable as a3m071 in the environment to determine if we
should boot into Linux or U-Boot.  This is useful on boards like
Beaglebone Black or AM335x GP EVM where we have persistent storage for
the environment.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Nishanth Menon
548a64d845 OMAP3: beagle-xm: generate fake USB ethernet MAC address from dieid
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 14:39:54 -04:00
Nishanth Menon
8a0c6d6fa9 OMAP: common: consolidate fake USB ethernet MAC address creation
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.

Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.

NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 14:39:54 -04:00
Wolfgang Denk
e7300f463d ARM: OMAP: remove sr32() from OMAP board code
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Albert ARIBAUD
519fdde9e6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	include/configs/trats.h
	include/configs/trats2.h
	include/mmc.h
2014-04-08 09:25:08 +02:00
Andreas Färber
2c67e0e7cf arm: Handle .gnu.hash section in ldscripts
Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-04-07 11:12:18 +02:00
Tom Rini
33ace362fd mmc: Add 'mmc rst-function' sub-command
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work.  Details on this being
required will be part of the eMMC datasheet.  Also add using this
command to the dra7xx README.

* Whitespace fix by panto

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:02:58 +03:00
Tom Rini
68996b84b6 am335x_evm: Clarify when we build board_eth_init
If we build this function in cases where we would be discarding it
anyhow we still end up with maybe unused warnings.  Rather than litter
the function with __maybe_unused, just spell out when to build it.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-28 15:15:10 -04:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Mugunthan V N
3a3939bf3d ARM: AM43xx: Add Ethernet boot support to SPL
Add Ethernet Boot support to SPL

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:07 -05:00
Lokesh Vutla
e27f2dd721 ARM: AM4372: Update EMIF registers for DDR3
Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD
registers.
In EMIF_PHY_CTRL:
Updating [4:0]READ_LATENCY to 8, because at higher frequencies like
400MHz the read latency expected will be CL+3 as per tests from HW
folks.
Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug
purpose. With out this resume is not working(Still waiting for PHY team
to come back for better explanation).

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
8feb37b9be ARM: DRA7xx: add support for reading cpsw 2nd mac from efuse
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also correct the bit masking of mac id read from the efuse.

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
a35ad51efe ARM: AM335x: add support for reading cpsw 2nd mac address from efuse
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Mugunthan V N
4cdd7fda91 ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVM
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
pekon gupta
32f4d729e7 board/ti/am335x/README: update for NAND boot
NAND boot mode on AM335x EVM has been verified, and steps
to use it has been documented and update in this README

Signed-off-by: Pekon Gupta <pekon@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Tom Rini <trini@ti.com>
2014-03-03 20:09:03 -06:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Albert ARIBAUD
b60eff31f3 arm: remove unneeded symbol offsets and _TEXT_BASE
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:12 +01:00
Albert ARIBAUD
d0b5d9da5d arm: make _end compiler-generated
This prevents references to _end from generating absolute
relocation records.

This change is binary invariant for ARM targets.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:09 +01:00
Dave Gerlach
cd8341b7eb ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator control
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:55:40 -05:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Dan Murphy
e9024ef27d ARM: O5/dra7xx: Add SATA boot support
Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-19 10:47:45 -05:00
Sourav Poddar
ea4c7a8321 am437x_epos_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:09 +05:30
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Tom Rini
b818d9ab8d dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
378ec0f816 omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Lokesh Vutla
0df8afdf10 ARM: AM43xx: Enable DDR dynamic IO power down for DDR3
This patch enables dynamically powering down the
IO receiver when not performing a read on DDR3 board.
This optimizes both active and standby power consumption.
This is derived from a patch that is done on AM335x[1]

[1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Jassi Brar
e81f63f0d2 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:38:39 -05:00
Mugunthan V N
e0a1d598ef ARM: dra7_evm: read mac address properly from e-fuse
Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is
not working on some boards, modifying the offset to read properly.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-01-07 16:41:12 -05:00
Lokesh Vutla
b5e01eecc8 ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:45 -05:00
Lokesh Vutla
d3daba10f1 ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:44 -05:00
Lokesh Vutla
965de8b91b ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18 21:14:18 -05:00
Lokesh Vutla
cf04d0326b ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
4892495e36 ARM: AM43xx: mux: Update mux data
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Sekhar Nori
f4af163e6c ARM: AM43XX: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support
CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and
CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the
board. These variables are used by findfdt.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Sekhar Nori
9f1a8cd33f ARM: AM43XX: board: add support for reading onboard EEPROM
Add support for reading onboard EEPROM to enable
board detection.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
369cbe1e1e ARM: AM43xx: Adapt to ti_armv7_common.h config file
Use ti_armv7_common.h config file to inclde the common
configs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Albert ARIBAUD
47ed5dd031 arm: keep all sections in ELF file
Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-12-07 06:53:58 +01:00
Hardik Patel
675cc77a3a pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
Signed-off-by: Hardik Patel <hardik.patel@volansystech.com>
2013-12-04 11:41:13 -05:00
Roger Quadros
21914ee62a ARM: dra7_evm: Add SATA support
The evm has a SATA port. Enable SATA configuration and
inititialize the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:36 -05:00
Roger Quadros
afdc632131 ARM: omap5_uevm: Add SATA support
The uevm has a SATA port. Inititialize the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Tom Rini
39245c8699 am33xx: Stop modifying certain EMIF4D registers
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified.  This has been tested
on AM335x GP EVM and Beaglebone White.

[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04 08:11:45 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
pekon gupta
2c17e6d1d9 am335x: fix GPMC config for NAND and NOR SPL boot
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Masahiro Yamada
e2906a5943 Makefile: rename all libraries to built-in.o
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:32 -05:00
Masahiro Yamada
1b2226e0ce Makefile: specifiy an explicite object name rather than $(BOARD).o
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:30 -05:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Tom Rini
79c5c08d7c omap730p2: Remove board
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11 12:17:48 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Tom Rini
6843918e00 am335x: Enable CONFIG_OMAP_WATCHDOG support
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:55:59 -04:00
Masahiro Yamada
4810400ec9 board: ti: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
2013-10-31 13:26:44 -04:00
Troy Kisky
7e575c46c3 usb: rename board_usb_init_type to usb_init_type
commit bba679144d
"usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c
So, fix that patch here, and fix a checkpatch warning.
WARNING: Avoid unnecessary line continuations

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-22 17:33:09 -04:00
Troy Kisky
127efc4fe8 usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.
This paramter will later be used to initialize OTG ports in
host or device mode.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:27 +02:00
Dan Murphy
ea02b653c2 ARM: omap5-evm: Move MAC creation to misc_init
Move the MAC creation from the USB init to an function
that is called on every boot.  This will then populate the
usbethaddr mac that kernel driver can pick up from the
device tree blob.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:42 +02:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
b216821189 usb: omap5: Update the board_usb_init api
Recent patches declares board_usb_init function prototype for a new
usb architecture.

Turning on the OMAP_XHCI defines cause a redefinition compiler failure.
So update the board_usb_init to the latest prototype.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Mateusz Zalega
16297cfb2a usb: new board-specific USB init interface
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.

New API allows selective initialization of USB controllers whenever needed.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20 23:42:40 +02:00
Dan Murphy
968055321e OMAP5-uevm: USB: Add xHCI host contoller support
Add the call back into the board file for to enable
the SMPS10 VBUS regulator.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Dan Murphy
e84b8f6ce0 ARM: omap4-panda: Add MAC address creation for panda
Add a MAC address create based on the OMAP die ID registers.
Then poplulate the ethaddr enviroment variable so that the device
tree alias can be updated prior to boot.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14 16:06:53 -04:00
Tom Rini
9f3fe6da27 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-08 09:51:48 -04:00
Albert ARIBAUD
0610a16cf2 omap1510inn: arm925t: remove support
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-10-07 19:25:19 +02:00
Matt Porter
247cdf0413 dra7xx_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:52 +05:30
Steve Kipisz
52f7d8442e am335x:Handle worst case scenario for Errata 1.0.24
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.

Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
9721027aae am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on.  In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed.  In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz.  In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1.  As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe.  In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:35 -04:00
Albert ARIBAUD
e62d5fb0da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-09-04 14:06:56 +02:00
Heiko Schocher
dafd4db33a arm, am33xx: add defines for gmii_sel_register bits
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-08-28 11:44:59 -04:00
Tom Rini
d7ccfc5bd6 am335x_evm: Update README for customization
As this is a reference platform, update the README to note which IP
blocks are required for use due to design choices of the reference
rather than required by the SoC itself.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28 11:44:59 -04:00
Taras Kondratiuk
e633ac0196 ARM: OMAP4460: sdp: Limit TPS mux config to 4460
TPS mux config is 4460 specific, so it should be limited to 4460 only.

Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28 11:44:58 -04:00
Oleksandr Tyshchenko
5b47f2d92b sdp4430: Initialize board id using CONFIG_MACH_TYPE
Use CONFIG_MACH_TYPE generic macro to set the machine type
number in the common arm code instead of setting it in the
board code.

Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
2013-08-28 11:44:58 -04:00
Dan Murphy
1572eadfbc ARM: OMAP5-uevm: Add usb device reset API
Add the call back to reset the LAN9730 after
the FEAT_POWER has been called.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26 21:56:34 +02:00
Dan Murphy
04025b42dc ARM: OMAP5-uevm: Add USB MAC ethernet address
Set the usbethaddr based on the OMAP DIE_ID registers
which should be unique for each processor.

Then set this as the usb ethernet MAC address.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26 21:56:34 +02:00
Dan Murphy
5e5cfaf997 ARM: OMAP5-uevm: Add USB ehci support for the uEVM
Add the USB ehci support for the OMAP5 uEVM.

Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26 21:56:31 +02:00
Dan Murphy
5a7bd38437 omap5: uevm: Change the board name to correct name
Change the board name for the sys info to
5432 uEVM

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-08-26 21:55:45 +02:00
TENART Antoine
425faf74cd Add TI816X evm board support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Tom Rini
73feefdc1a am33xx: Stop using PHYS_DRAM_1 define
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE.  But then we kept on referencing PHYS_DRAM_1
in other places.  Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:35 -04:00
Lokesh Vutla
3b34ac13fe ARM: AM43xx: clocks: Add dpll and clock data
Add dpll and clock data for AM43xx

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
fbf2728da3 ARM: AM43xx: Add Board files
Add board specific information for AM43xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Heiko Schocher
0660481a59 ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Dan Murphy
fdce7b633a gpio: omap5-uevm: Configure the tca6424 gpio expander
Configure the tca6424 gpio expander
This allows use of the debug and tri color LEDs.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-07-30 09:21:42 -04:00
Tom Rini
486da22967 board/ti/am335x/README: Document NOR programming
The Beaglebone White may be populated with a memory cape that has a NOR
module.  Document how to program it.

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Steve Kipisz
c5c7a7c32d am335x_evm: Add support to boot from NOR.
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on.  When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB.  We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.

We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Steve Kipisz
cd8845d7a4 am335x_evm: Add support for the NOR module on the memory cape
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Tom Rini
ace4275eb3 am335x_evm: Rework board_is_foo() checks
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.

Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Tom Rini
97559b5203 board/ti/am335x/README: Document NAND programming
The AM335x GP EVM ships with NAND.  Document programming of the chip
including the redundant locations that the ROM will check.

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:37 -04:00
Nishanth Menon
af4d896fed beagleboard: remove RevB support for BeagleBoard Xm
As reported in http://marc.info/?l=u-boot&m=137358037827735&w=2

There is no need for the "xMB" variant, as the gpio pins used for
identification where never changed from the xMA when the newer silcon
was used for the xMB, So rename XM A revision as AB revision
and report accordingly

Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
dec7f74835 ARM: DRA7xx: Add CPSW and MDIO pinmux support
Adding CPSW Slave 0 and MDIO pinmux support for DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Mugunthan V N
2bf36ac638 drivers: net: cpsw: remove hard coding bd ram for cpsw
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Tom Rini
5d4dbf1c3a am335x_evm: Add basic README
Add a README for the family of boards the am335x_evm covers, and include
instructions on preparing and using falcon mode, for various media.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
348e47f766 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-22 07:38:12 -04:00
Dan Murphy
bf3b98a188 arm: omap4: panda: Fix checkpatch on panda file
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-06-18 10:43:30 -04:00
Dan Murphy
7d47d1caa0 arm: omap4: panda: Add reading of the board revision
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
     GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
     GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3

Set the board name appropriately for the board revision that
is detected.

Update the findfdt macro to load the a4 device tree binary.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
 formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:30 -04:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Tom Rini
7f5eef93af arm: Remove OMAP2420H4 and all omap24xx support
The omap2420H4 was the only mainline omap24xx board.  Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time.  Remove this board as there's not been interest in
it in U-Boot for quite a long time.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:19 -04:00
Lokesh Vutla
7f36c88f64 ARM: DRA7xx: Update pinmux data
Updating pinmux data as specified in the latest DM

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
af1d002f89 ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.h
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
9239f5b625 ARM: OMAP4+: Cleanup header files
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Joel A Fernandes
a662e0c345 am33xx: Board: Make CPSW section of ethernet initialization depend on CPSW driver
Not doing so breaks cases where CPSW is not required such as for USB RNDIS network boot.

Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
2013-06-10 08:43:08 -04:00
Peter Korsgaard
12d7a47420 am335x: enable falcon boot mode for mmc (raw and fat) and nand
Jump into full u-boot mode if a 'c' character is received on the uart.

We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.

For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.

This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2013-06-07 14:17:01 -04:00
Tom Rini
4596dcc1d4 am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common.  Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx.  Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.

Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-05 08:46:49 -04:00
Dan Murphy
34f667bbc4 ARM:Panda:Fix device tree loading for the panda-es
Fix the device tree loading for panda(4430) and panda-es(4460)

Modify the board name if a 4460 panda or panda-es is detected
at run time.
In the findfdt add a check for the panda-es board name and load
the panda-es device tree blob.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-05-10 08:25:55 -04:00
Tom Rini
8ce4e5f932 beagleboard: Update comment in get_board_rev()
We are able to tell the difference between xM Rev Ax/Bx and xM Rev Cx,
and have been for some time.  The comment above the function however did
not list this, so update.

Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:55 -04:00