This configures the PLL5P clock frequency to something in the ballpark
of 1GHz and allows more choices for MBUS and G2D clock frequency
selection (using their own divisors). In particular, it enables the use
of 2/3 clock speed ratio between MBUS and DRAM.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
http://linux-sunxi.org/A10_DRAM_Controller_Performance
This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.
PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.
Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:
http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0
The new code supports both of the impedance configuration modes:
- If the higher bits of the 'zq' parameter in the 'dram_para' struct
are zero, then the lowest 8 bits are used as the ZPROG value, where
two divisors encoded in lower and higher 4 bits. One divisor is
used for calibrating the termination impedance, and another is used
for the output impedance.
- If bits 27:8 in the 'zq' parameters are non-zero, then they are
used as the pre-defined ZDATA value instead of performing the ZQ
calibration.
Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The old 'await_completion' function is not sufficient, because
in some cases we want to wait for bits to be cleared, and in the
other cases we want to wait for bits to be set. So split the
'await_completion' into two new 'await_bits_clear' and
'await_bits_set' functions.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The older differences were likely justified by the need to mitigate
the CKE delay timing violations on sun4i/sun5i. The CKE problem is
already resolved, so now we can use the sun7i variant of this code
everywhere.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We can safely remove it, because none of the currently supported
boards uses these features.
The existing implementation had multiple problems:
- unnecessary code duplication between sun4i/sun5i/sun7i
- ZQ calibration was never initiated explicitly, and could be
only triggered by setting the highest bit in the 'zq' parameter
in the 'dram_para' struct (this was never actually done for
any of the known Allwinner devices).
- even if the ZQ calibration could be started, no attempts were
made to wait for its completion, or checking whether the
default automatically initiated ZQ calibration is still
in progress
- ODT was only ever enabled on sun4i, but not on sun5i/sun7i
Additionally, SDR_IOCR was set to 0x00cc0000 only on sun4i. There
are some hints in the Rockchip Linux kernel sources, indicating
that these bits are related to the automatic I/O power down
feature, which is poorly understood on sunxi hardware at the
moment. Avoiding to set these bits on sun4i too does not seem to
have any measurable/visible impact.
The impedance and ODT configuration code will be re-introdeced in
one of the next comits.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Before driving the CKE pin (Clock Enable) high, the DDR3 spec requires
to wait for additional 500 us after the RESET pin is de-asserted.
The DRAM controller takes care of this delay by itself, using a
configurable counter in the SDR_IDCR register. This works in the same
way on sun4i/sun5i/sun7i hardware (even the default register value
0x00c80064 is identical). Except that the counter is ticking a bit
slower on sun7i (3 DRAM clock cycles instead of 2), resulting in
longer actual delays for the same settings.
This patch configures the SDR_IDCR register for all sun4i/sun5i/sun7i
SoC variants and not just for sun7i alone. Also an explicit udelay(500)
is added immediately after DDR3 reset for extra safety. This is a
duplicated functionality. But since we don't have perfect documentation,
it may be reasonable to play safe. Half a millisecond boot time increase
is not that significant. Boot time can be always optimized later.
Preferebly by the people, who have the hardware equipment to check the
actual signals on the RESET and CKE lines and verify all the timings.
The old code did not configure the SDR_IDCR register for sun4i/sun5i,
but performed the DDR3 reset very early for sun4i/sun5i. This resulted
in a larger time gap between the DDR3 reset and the DDR3 initialization
steps and reduced the chances of CKE delay timing violation to cause
real troubles.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The RESET pin needs to be kept low for at least 200 us according
to the DDR3 spec. So just do it the right way.
This issue did not cause any visible major problems earlier, because
the DRAM RESET pin is usually already low after the board reset. And
the time gap before reaching the sunxi u-boot DRAM initialization
code appeared to be sufficient.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If the dram->ppwrsctl (SDR_DPCR) register has the lowest bit set to 1,
this means that DRAM is currently in self-refresh mode and retaining the
old data. Since we have no idea what to do in this situation yet, just
set this register to 0 and initialize DRAM in the same way as on any
normal reboot (discarding whatever was stored there).
This part of code was apparently used by the Allwinner boot0 bootloader
to handle resume from the so-called super-standby mode. But this
particular code got somehow mangled on the way from the boot0 bootloader
to the u-boot-sunxi bootloader and has no chance of doing anything even
remotely sane. For example:
1. in the original boot0 code we had "mctl_write_w(SDR_DPCR,
0x16510000)" (write to the register) and in the u-boot it now looks
like "setbits_le32(&dram->ppwrsctl, 0x16510000)" (set bits in the
register)
2. in the original boot0 code it was issuing three commands "0x12, 0x17,
0x13" (Self-Refresh entry, Self-Refresh exit, Refresh), but in the
u-boot they have become "0x12, 0x12, 0x13" (Self-Refresh entry,
Self-Refresh entry, Refresh)
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The attempt to do DRAM parameters calibration in 'dramc_scan_dll_para()'
function by trying different DLL adjustments and using the hardware
DQS gate training result as a feedback is a great source of inspiration,
but it just can't work properly the way it is implemented now. The fatal
problem of this implementation is that the DQS gating window can be
successfully found for almost every DLL delay adjustment setup that
gets tried. Thus making it unable to see any real difference between
'good' and 'bad' settings.
Also this code was supposed to be only activated by setting the highest
bit in the 'dram_tpr3' variable of the 'dram_para' struct (per-board
dram configuration). But none of the linux-sunxi devices has ever used
it for real. Basically, this code is just a dead weight.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Maxin B. John <maxin.john@enea.com>
The vectors section contains the _start symbol which is used as the
program entry point. Add it to the linker script in same fashion as done
for regular u-boot. This allows for correct generation of an spl elf
with a non-zero entry point.
A similar change was applied to sunxi platform in
"sunxi: Fix u-boot-spl.lds to refer to .vectors"
(sha1: 9e5f80d823)
This also allows for placement of the vector table at the hivecs
location by setting the TEXT_BASE to 0xffff0000.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
'omux' field is not used anywhere and such layout is not valid for mx6solox.
Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
- move blackfin specific cpu init code from blackfin board.c to cpu.c
- remove blackfin specific board init code and invoke generic board_f fron cpu init entry
- rename section name bss_vma to bss_start in order to match the generic board init code
- add a fake relocate_code function to set up the new stack only
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.
If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
When CONFIG_WATCHDOG is defined the board initialization just performs
a WATCHDOG_RESET, an initialization of the watchdog is not done.
This has been modified fot the MPC85xx, the board initialization calls
its watchdog initialitzation allowing for full watchdog configuration
very early in the boot phase.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function to inititialize the cpu watchdog added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
[York Sun: Add prototype in watchdog.h]
Reviewed-by: York Sun <yorksun@freescale.com>
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.
The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):
watchdog_period = 1/fTB * 2^x
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
TCR watchdog bit are overwritten when dec interrupt is enabled.
This has been fixed with this patch.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Unify the register structure so they can be easily used across all
of S3C24xx lineup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
So far, only supporting the CPU_ON method.
Other functions can be added later.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On some boards the ethernet-phy needs to be powered up through a gpio,
add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CONFIG_${CPU} is defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.
Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.
Usage:
Run "make <board>_defconfig" to do the board configuration.
It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.
You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.
Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.
The generic syntax of configuration targets for SPL, TPL is:
<target_image>/<config_command>
Here, <target_image> is either 'spl' or 'tpl'
<config_command> is 'config', 'menuconfig', 'xconfig', etc.
When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)
For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.
By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.
Prior to Kconfig, we used C headers to define a set of configs.
We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.
In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds more Kconfig files, which were written by hand.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Having a form of whitelist to check if we know of a CPU core
and and obtain CBAR is a bit silly.
It doesn't scale (how about A12, A17, as well as other I don't know
about?), and is actually a property of the SoC, not the core.
So either it works and everybody is happy, or it doesn't and
the u-boot port to this SoC is providing the real address via
a configuration option.
The result of the above is that this code doesn't need to exist,
is thus forcefully removed.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Generate the PSCI node in the device tree.
Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.
[maz: collapsed 3 patches into one, rewrote commit message]
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allow the switch to a second stage secure monitor just before
switching to non-secure.
This allows a resident piece of firmware to be active once the
kernel has been entered (the u-boot monitor is dead anyway,
its pages being reused).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.
This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
before entering the payload
- performing an exception return from secure mode directly into
the payload
- allowing the code to be dynamically relocated to secure RAM
before switching to non-secure.
This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In anticipation of refactoring the HYP/non-secure code to run
from secure RAM, add a new linker section that will contain that
code.
Nothing is using it just yet.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.
Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Before switching to non-secure, make sure that CNTVOFF is set
to zero on all CPUs. Otherwise, kernel running in non-secure
without HYP enabled (hence using virtual timers) may observe
timers that are not synchronized, effectively seeing time
going backward...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
A CP15 instruction execution can be reordered, requiring an
isb to be sure it is executed in program order.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Having the switch to non-secure in the "prep" phase is causing
all kind of troubles, as that stage can be called multiple times.
Instead, move the switch to non-secure to the last possible phase,
when there is no turning back anymore.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fixes commit a0a37183bd
ARM: omap: merge GPMC initialization code for all platform
1) NAND device are not directly memory-mapped to CPU address-space, they are
indirectly accessed via following GPMC registers:
- GPMC_NAND_COMMAND_x
- GPMC_NAND_ADDRESS_x
- GPMC_NAND_DATA_x
Therefore from CPU's point of view, NAND address-map can be limited to just
above register addresses. But GPMC chip-select address-map can be configured
in granularity of 16MB only.
So this patch uses GPMC_SIZE_16M for all NAND devices.
2) NOR device are directly memory-mapped to CPU address-space, so its
address-map size depends on actual addressable region in NOR FLASH device.
So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
size configuration.
Signed-off-by: Pekon Gupta <pekon@ti.com>
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone2 K2E SoC has slightly different spl pll settings then
K2HK, so correct this.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This driver is needed in case if keystone driver is used.
Currently only keystone_net driver uses it. So to avoid
redundant code compilation make the keystone_nav dependent
on keystone net driver. It also leads to compilation errors
for boards that does't use it.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
These functions have been merged into the common GPMC init code
with this commit a0a37183 (ARM: omap: merge GPMC initialization code
for all platform). The file is not compiled any more. So remove it
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Commit a0a37183 (ARM: omap: merge GPMC initialization code for all
platform) broke NAND on OMAP3 based platforms. I noticed this while
testing the latest 2014.07-rc version on the TAO3530 board. NAND
detection did not work with this error message:
NAND: nand: error: Unable to find NAND settings in GPMC Configuration - quitting
As OMAP3 configs don't set CONFIG_NAND but CONFIG_NAND_CMD. the GPMC
was not initialized for NAND at all. This patch now fixes this issue.
Tested on TAO3530 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
The generic board infrastructure assumes that gd is set by
arch code.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Renesas R8A7794 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The linker scripts of sh2/sh3/sh4 are almost the same.
The difference among them is essentially only one line.
They can be consolidated into a single file, arch/sh/cpu/u-boot.lds
by re-writing the diffrent line as follows:
KEEP(*/start.o (.text))
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Without this patch is DRAM size one line below DRAM:
which is not nice
Origin:
I2C: ready
DRAM: Memory: ECC disabled
1 GiB
MMC: zynq_sdhci: 0
Fixed by this patch:
I2C: ready
DRAM: ECC disabled 1 GiB
MMC: zynq_sdhci: 0
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Drivers are supposed to be able to close down cleanly. To set a good example,
make sandbox shut down its driver model drivers and remove them before exit.
It may be desirable to do the same more generally once driver model is more
widely-used. This could be done during bootm, before U-Boot jumps to the OS.
It seems far too early to make this change.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
There is no point in setting a structure's memory to NULL when it has
already been zeroed with memset().
Also, there is no need to create a stub function for stdio to call - if the
function is NULL it will not be called.
This is a clean-up, with no change in functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Set up and zero global data before board_init_f() is called so that we can
remove the need for CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f().
If we set up and zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change to simplify the init process.
Signed-off-by: Simon Glass <sjg@chromium.org>
On mx6solox there is an additional 0x4000 offset for the GPR registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
When resume from deep sleep, uboot needs to enable L2 and CPC
cache, or they would be keeping unusable in kernel because
kernel didn't enble or initialized them.
This patch didn't change the existing L2 cache enabling code,
just put them in a function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
