Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.
U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.
Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx28evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
There are more Allwinner SoCs that do not have a SCP now.
When there's no SCP_ADDR macro defined, we can assume there's no SCP
available.
Drop the scp part of FIT description when SCP_ADDR does not exist.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Khadas vim series: Use devicetree for SMBIOS settings
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the "/reserved-memory/optee" node to the SPL devicetree. The
purpose is to allow configuring TZC regions when booting OP-TEE.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 500327e2ea ("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.8-rc1")
renamed sdmmc2_d47_pins_b phandle to sdmmc2_d47_pins_c, but without updating
the AV96 DT which uses that phandle. Linux missed similar update as well and
it was only added in commit 1ad6e36ec266 ("ARM: dts: stm32: Fix sdmmc2 pins
on AV96") .
Update the AV96 DT pinmux phandle, otherwise eMMC 8bit mode does not work
and access to eMMC takes a very long time to fall back to 4bit mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.
So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MAIN R5FSS0 cluster and corresponding nodes are no longer required
to be enabled in R5 SPL after removing the support for booting any core
from this cluster on R5 SPL. So, remove these from the relevant dts
files.
This is essentially a revert of the additions done in commit 2984b82b3b
("arm: dts: k3-j721e-r5: Enable r5fss0 cluster in SPL").
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-5-s-anna@ti.com
The default U-Boot environment variables and design are all set up to
have the MCU R5FSS cluster to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit 468ec2f3ef ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.
The mode for the cluster got switched back to LockStep mode by mistake
in commit e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts
into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,
k3_r5f_rproc r5f@41400000: Invalid op: Trying to start secondary core 2 in lockstep mode
Load Remote Processor 1 with data@addr=0x82000000 65268 bytes: Failed!
Fix this by switching back the cluster to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes: e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726162213.28719-1-s-anna@ti.com
A Wilink wireless device is connected to MMCSD0 subsystem and is not
supported in U-Boot. Therefore, disable main_sdhci0 device tree node in
U-Boot.
If main_sdhci0 device tree node is disabled then the the index of
main_sdhci1 node becomes 0 which leads to break in boot flow. Therefore,
add an alias to fix the index to 1.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-3-a-govindraju@ti.com
Add u-boot tags for torrent serdes. This has properties specific to
u-boot on top of DT in v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-15-kishon@ti.com
Add default lane function for torrent serdes. This is in sync
with v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-14-kishon@ti.com
Add DT node for torrent serdes. This is in sync with v5.13 Linux Kernel.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-13-kishon@ti.com
Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
These device trees are updated to match the versions in Linux 5.13.1.
The tick-timer entry in am335x-bone-common.dtsi is preserved.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
HS400 speed mode is now supported in J7200 SoC[1]. Therefore add
mmc-hs400-1_8v tag in sdhci0 device tree node.
Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
(SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
(SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210525093826.10390-3-a-govindraju@ti.com
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.
Switch over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add partition information to the spi-nor flash.
This is required for accessing NOR flash via mtdparts.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
The RPC HF might be locked by ATF, and any access to its register
space would result in complete hang. Disable the RPC HF by default.
The ATF should be patched to set RPC node status = "okay" in the DT
fragment it passes to U-Boot in case the RPC HF access is unlocked,
and that way U-Boot could access the RPC HF safely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add sysinfo node and phandle to the board ID EEPROM on all boards
where this functionality is described in DT, which is Salvator-X(S),
ULCB and Ebisu. The u-boot,dm-pre-reloc is necessary here, since the
sysinfo must be available early during boot. The V3M and V3H boards
currently do not describe this board ID EEPROM in upstream DT, but
that could be easily added later, once the DTs contain the necessary
nodes.
ULCB and Ebisu needs the full EEPROM node in the u-boot extras DT,
since the EEPROM node is still missing in the upstream DTs. Ebisu
also needs extra compatible string override for the i2c_dvfs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RGMII ports on LS1043ARDB platforms require both RX and TX internal
delays to be enabled. The device tree reports only the TX ID because the
RX ID used to be enabled by default.
With the addition of RX ID support for the Realtek 8211F PHY driver in
commit e32e4d0f58 ("net: phy: realtek: add rx delay support for
RTL8211F"), the RX ID is disabled by the driver if not reported explicitly.
This causes the RX to no longer work.
Change the phy-connection-type for the RGMII ports to "rgmii-id" in order
to enable both RX and TX internal delays.
Fixes: be1d758969 ("ARM: dts: add QorIQ DPAA 1 FMan v3 to LS1043ARDB")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Specify a separate partition `u-boot-env` for U-Boot's env settings for
the Turris Omnia board.
Do this only in U-Boot's specific DTS. We do not want to do this in
Linux' official DTS, because Omnia's stock U-Boot stores env at a
different address, and there are still boards with stock U-Boot.
In a subsequent patch will add board code that fixes Linux's DTB before
booting Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add device tree kirkwood-nsa310s.dts for Zyxel NSA310S board to
convert to Driver Model.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
