Commit graph

114 commits

Author SHA1 Message Date
Kumar Gala
093cffbe9a powerpc/85xx: Support for Freescale P1024/P1025 processor
Add Support for Freescale P1024/P1025 (dual core) and
P1015/P1016 (single core) processors.

P1024 is a variant of P1020 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1025 is a variant of P1021 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1015 is a variant of P1024 processor with single core and P1016 is a
variant of P1025 processor with single core.

Added comments in config_mpc85xx.h to denote single core versions of
processors.

Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
0b3b1766b7 fsl_ddr: Adds 16 bit DDR Data width option
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Prabhakar Kushwaha
b6ccd2c9de fsl_pci: Add support for FSL PCIe controllers v2.x
FSL PCIe controller v2.1:
	- New MSI inbound window
	- Same Inbound windows address as PCIe controller v1.x

Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window

FSL PCIe controller v2.2 and v2.3:
	- Different addresses for PCIe inbound window 3,2,1
	- Exposed PCIe inbound window 0
	- New PCIe interrupt status register

Added new Interrupt Status register to struct ccsr_pci & updated pit_t array
size to reflect the 4 inbound windows.

To maintain backward compatiblilty, on V2.2 or greater controllers we
start with inbound window 1 and leave inbound 0 with its default value
(which maps to CCSRBAR).

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Haiying Wang
24995d829a powerpc/85xx: Refactor Qman/Portal support to be shared between SoCs
There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.

* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
  (features doesn't exist on P1023/P1017)

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Roy Zang
67a719da2e powerpc/85xx: Add support for Freescale P1023/P1017 Processors
Add P1023 (dual core) & P1017 (single core) specific information:
* SERDES Table
* Added P1023/P1017 to cpu_type_list and SVR list
  (fixed issue with P1013 not being sorted correctly).
* Added P1023/P1027 to config_mpc85xx.h
* Added new LAW type introduced on P1023/P1017
* Updated a few immap register/defines unique to P1023/P1017

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fdb4dad31e powerpc/85xx: Cleanup some QE related defines
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.

Also fixed up some comment style issues in immap_qe.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fbee0f7f09 powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020
Specify the number of DDR controllers, number of frame managers, number
of 1g and 10g ports.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Kumar Gala
f0f899432e powerpc/85xx: Declare fsl_ddr_set_memctl_regs in <asm/fsl_ddr_sdram.h>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.

Based on patch from Poonam Aggrwal.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Dipen Dudhat
d789b5f5bc powerpc/85xx: Add support for Integrated Flash Controller (IFC)
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.

Features supported by IFC are,
        - Functional muxing of pins between NAND, NOR and GPCM
        - Support memory banks of size 64KByte to 4 GBytes
        - Write protection capability (only for NAND and NOR)
        - Provision of Software Reset
        - Flexible Timing programmability for every chip select
        - NAND Machine
                - x8/ x16 NAND Flash Interface
                - SLC and MLC NAND Flash devices support with
                  configurable
                  page sizes of upto 4KB
                - Internal SRAM of 9KB which is directly mapped and
                  availble at
                  boot time for NAND Boot
                - Configurable block size
                - Boot chip select (CS0) available at system reset
        - NOR Machine
                - Data bus width of 8/16/32
                - Compatible with asynchronous NOR Flash
                - Directly memory mapped
                - Supports address data multiplexed (ADM) NOR device
                - Boot chip select (CS0) available at system reset
        - GPCM Machine (NORMAL GPCM Mode)
                - Support for x8/16/32 bit device
                - Compatible with general purpose addressable device
                  e.g. SRAM, ROM
                - External clock is supported with programmable division
                  ratio
        - GPCM Machine (Generic ASIC Mode)
                - Support for x8/16/32 bit device
                - Address and Data are shared on I/O bus
                - Following Address and Data sequences can be supported
                  on I/O bus
                       - 32 bit I/O: AD
                       - 16 bit I/O: AADD
                       - 8 bit I/O : AAAADDDD
                - Configurable Even/Odd Parity on Address/Data bus
                  supported

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Prabhakar Kushwaha
28747f9bb1 powerpc/85xx: Add SERDES support for P1010/P1014
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are only
ever connected on SERDES.

Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Prabhakar Kushwaha
b03a466d6c powerpc/85xx: Handle PCIe initialization requires for P1021 class SoCs
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe.  Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-29 07:41:37 -05:00
Jiang Yutang
2d7534a344 powerpc/85xx: Enable various errata on P1022/P1013 SoCs
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.

Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-28 09:04:26 -05:00
York Sun
08b3f7599f powerpc/mpc8xxx: fix recognition of DIMMs with ECC and Address Parity
To recognize DIMMs with ECC capability by testing ECC bit only. Not to be
confused by Address Parity bit.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-24 09:20:49 -05:00
Wolfgang Denk
fced09ae38 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2011-02-09 20:50:26 +01:00
Dirk Eibach
2da0fc0d0f ppc4xx: Add DLVision-10G board support
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-02-07 11:13:16 +01:00
York Sun
91671913f7 powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
         calibrate to incorrect values

These two workarounds must be implemented together because they touch
common registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
York Sun
eb0aff77c8 powerpc/85xx: Rename MPC8572 DDR erratum to DDR115
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
Kumar Gala
5103a03a0b fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Kumar Gala
6e7f0bc0ce powerpc/85xx: Enable ESDHC111 Erratum on P2010/P2020 SoCs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Wolfgang Denk
d1a24f0618 Minor Coding Style Cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-02-02 22:36:10 +01:00
York Sun
6b06d7dc07 corenet_ds: Extend board specific parameters
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00
York Sun
fa8d23c0ee mpc85xx: Implement workaround for erratum DDR-A003
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00
York Sun
e1fd16b6f5 mpc85xx: Enable unique mode registers and dynamic ODT for DDR3
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.

Enable address parity and RCW by default for RDIMMs.

Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.

Use a formula to calculate rodt_on for timing_cfg_5.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
York Sun
d2a9568c57 mpc85xx: Adding more registers and options
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.

Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Kumar Gala
243be8e296 powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headers
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.

Eventually this should be handled by Kconfig & defconfigs

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-19 22:58:23 -06:00
Kumar Gala
f193e3da98 powerpc/p2040: Add various p2040 specific information
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b5debec5b5 powerpc/85xx: Add Support for Freescale P1014 Processor
The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b8cdd01462 powerpc/85xx: Add Support for Freescale P1010 Processor
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Prabhakar
17028be238 Fix wrong CONFIG_SYS_MPC85xx_SERDES1_ADDR
CONFIG_SYS_MPC85xx_SERDES1_ADDR was defined wrong as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES2_OFFSET.
It should be as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2011-01-19 22:58:23 -06:00
Kumar Gala
f133796da8 powerpc/85xx: Add the workaround for erratum ELBC-A001 (enable on P4080)
Simultaneous FCM and GPCM or UPM operation may erroneously trigger bus
monitor timeout.  Set timeout to maximum to avoid.

Based on a patch from Lan Chunhe <b25806@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
868da5936e powerpc/85xx: Add the workaround for erratum CPC-A003 (enable on P4080)
CoreNet Platform Cache single-bit data error scrubbing will cause data
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
1d2c2a62e3 powerpc/85xx: Add the workaround for erratum CPC-A002 (enable on P4080)
CoreNet Platform Cache single-bit tag error scrubbing will cause tag
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
3dbd5d7d7e powerpc/8xxx: Move fsl_is_spd() into generic 8xxx ddr code
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
5655136208 powerpc/86xx: Enable common SRIO init code
Add the needed defines and code to utilize the common 8xxx srio init
code to setup LAWs and modify device tree if we have SRIO enabled on a
board.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:21 -06:00
Kumar Gala
a09b9b68d4 powerpc/8xxx: Refactor SRIO initialization into common code
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO.  We mimic what we do with PCIe
controllers for SRIO.

We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.

We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.

Introduced the following standard defines for board config.h:

CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available

(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)

[ These mimic what we have for PCI and PCIe controllers ]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:21 -06:00
Peter Tyser
213ac73e2c fsl_pci: Update PCIe boot ouput
This change does the following:
- Adds printing of negotiated link width.  This information can be
  useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
  Previously boards that did not implement it would print unsightly
  output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
  clear that the "base address XYZ" value refers to the base address of
  the internal processor PCIe registers and not a standard PCI BAR
  value.
- Changes "PCIE" output to the standard "PCIe"

Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06

After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:21 -06:00
Kumar Gala
a4aafcc990 powerpc/fsl-pci: Add generic code to setup PCIe controllers
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled.  After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.

We also provide a per controller (rather than all) for some systems that
may have special requirements.

Finally, we refactor the code used by the P1022DS to utilize the new
generic code.

Based on patch by: Li Yang <leoli@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Kumar Gala
3a0e3c27a5 powerpc/fsl-pci: Determine pci_controller based on cfg addr for dts fixup
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus.  Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.

Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:19 -06:00
Becky Bruce
70961ba414 mpc85xx: rename sdram_init() lbc_sdram_init()
sdram_init() is used to initialize sdram on the lbc.  Rename it
accordingly.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Becky Bruce
38dba0c2ff mpc85xx boards: initdram() cleanup/bugfix
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts.  Most
of the initdram() functions were identical, with 2 common differences:

1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others.  I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.

2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document.  It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled.  This seems bad.

The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Kumar Gala
5d27e02c04 powerpc/8xxx: Replace is_fsl_pci_cfg with is_serdes_configured
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Piergiorgio Beruto
afabe4b94e powerpc/85xx: Fix wrong SVR value for MPC8567 and MPC8567E processors
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
York Sun
28a966715b Adding fixed sdram setting for cornet_ds board
800, 900, 1000, 1200MT/s data rate parameters are added for fixed sdram
setting. SPD based parameters and fixed parameters can be toggled by hwconfig.
To use fixed parameters,

hwconfig=fsl_ddr:sdram=fixed

To use SPD parameters,

hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:38:39 -05:00
Kumar Gala
a1964ea5c2 powerpc/8xxx: Add fdt_fixup_phy_connection helper
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:27:18 -05:00
Kumar Gala
f8c42495e0 powerpc/fsl: Introduce common enum for PHY types
Have a common enum for phy types that we use in the UCC driver.  We will
also use this enum for dealing with phy connection fixup in the device
tree.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:27:18 -05:00
John Rigby
fca43cc801 boot: change some arch ifdefs to feature ifdefs
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.

Use CONFIG_SYS_BOOT_<FEATURE> defines instead.

CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD

Define these as appropriate in arch/include/asm/config.h files.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:53:32 +02:00
Peter Tyser
d98b0523cf powerpc: Cleanup BOOTFLAG_* references
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-18 22:38:56 +02:00
Damien Dusha
29c6fbe047 MPC5121: Add USB EHCI support
Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com>
Signed-off-by: Damien Dusha <d.dusha@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-10-18 22:33:32 +02:00