Since we are using revD1 device tree for all board revisions, the
following can be seen on a revB1 board:
Model: Wandboard i.MX6 Quad Board revD1
Board: Wandboard rev B1
To avoid such confusing messages, disable CONFIG_DISPLAY_BOARDINFO_LATE.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
mxsfb needs a dcache function not implemented in cortex-M7, so for the
moment let's keep dcache not enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_VIDEO subsystem and its BACKLIGHT_GPIO. Then enable
SYS_WHITE_ON_BLACK to have classic black background on display. Need
also to enable CONFIG_SYS_CONSOLE_ENV_OVERWRITE to retrieve
stdin/stdout/stderr from CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx6ulz-evk board does not have networking support, explicitly
disable networking to avoid the board removal.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
CONFIG_FEC_MXC is supported in Kconfig, so it is preferred to
move it to defconfig file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is pretty minor set of changes mostly touching HSDK board:
* Enable on-chip reset controller on HSDK
* Add possibility to turn-on & off L2$ on more
recent ARC HS processors.
* AXI tunnel clock calculation on HSDK
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl6YjlcACgkQxIHbvCwF
GsQ6Jg/+KVRQF0Dn2jiag8Me9ZhafZx4xGTI3LEzFD7V9kG3dmUzbO3m8a5dEevW
bcPNA6EmcKAjyP09AZY4C8ns4sU7wzPu/GQvApD4S5+vcuNbEqRHfW6zzReNXq09
t89DrFH+XLhGnh4uSh0hmfjrlIPVi86hs/f57vKRayrBu8W2yGPci3SNTO5Y0AY1
to7sxP3hGlDCUhqIABWp5ylpWWUSG1MsVNcMOnHpj+jl0iWWYP46EQrGr95egQor
gcGgUOLdOLLOHPYUIOBmo9INnS2MbvE9Mfgh5Bw7JW8DIu/Xp7r1qePQyMLsngc1
pO5yzwMq6EQy6OjuYnXdIBXtHOlZ8rnE9pbTgyUR8T/2CdL2hqr9ddpqa4ryDABX
iaQF8FG+KhY0XQ5EIJV7pEkvf9TMwGguJNlOkmJPeub2n9i0k1tPk0Rwq5ZWWBIn
rHcgZXwl0On3O3f0HvfL0Oas5u9KE1HhA12h/EVmu2Muy36x2WxAAzDnsH19HzqU
QnWBAo8VMyp3qTIZjb3y+qrxcU/joPGt9+hxmur03hzmKOJ9JNOv6vExb+yUIyXQ
4ML6jvTvSVZbvkP++0zMKOjT8ks3xv5q84oFD5Gp4cG8ZpHpA9dj3mXM92Waepo4
pAkko5IGQ4SqaGIBltEQzrG+cCiHHezdD/raCwAo6DgYSmfZUvc=
=+ZDZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc1
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
As the driver of on-chip reset controller became available
we are ready to enable it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl6YdaMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYLRwf8C+vKmERVLLcrMZMMiLctbY2kVflJV8zG
RjFwBcazZDPYjtHqClFZtJyIDYzgkVQRo+QPcdLxjcA+gjSXdteeRa0XTsBTXOZQ
kbs7yBkL+rCIO2WyXtuyajsmDMQtqM5vYgeBdTeYnJu7NVxwRMYrUqqAKLolNpIN
SKNYz+a8OEOG2EetbTdwwrmSpNy/cZ3wDGYK25DFTte8/vCZMRBTPiiNSrLp/RsM
xIojRcLqzARwpvPfFZ8psASKei9+5oIICUrNvwwQGtjepvZwdFQEl90SKaHw8kMf
sP9rxuqlEN5ec6xnMTUgwfnyBZgNIMSeb4KVPP1rxN2eAa5+bK1OlQ==
=gyyY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10apr20-take2' of git://git.denx.de/u-boot-dm
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
'bootefi hello' is used in one of the Python tests.
efidebug can be used to verify the correct initialization of the UEFI
sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromum.org>
For testing purposes enable the syslog logging driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
ACPI (Advanced Configuration and Power Interface) is a standard for
specifying information about a platform. It is a little like device
tree but the bindings are part of the specification and it supports an
interpreted bytecode language.
Driver model does not use ACPI for U-Boot's configuration, but it is
convenient to have it support generation of ACPI tables for passing to
Linux, etc.
As a starting point, add an optional set of ACPI operations to each
device. Initially only a single operation is available, to obtain the
ACPI name for the device. More operations are added later.
Enable ACPI for sandbox to ensure build coverage and so that we can add
tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Adding those extra configurations allows us to successfully run UEFI
secure boot pytest on Travis CI.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Enable these standard U-Boot commands for image manipulation and for
starting the default boot command using 'boot' command in U-Boot shell.
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
In order to support MOX boards with 2 GB or 4 GB RAM, we use the new
Armada-3700 generic code for memory information structures. This is done
by removing dram_init and dram_init_banksize from turris_mox.c, in order
for the generic, weak definitions to be used.
Also for boards with 4 GB RAM it is needed to increase
CONFIG_NR_DRAM_BANKS to 2 in turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Patch Linux's device tree according to which Mox modules are connected.
Linux's device tree has all possible Mox module nodes preprogrammed, but
in disabled state.
If MOX B, MOX F or MOX G module is present, this code enables the PCI
node.
For the network modules (MOX C, MOX D and MOX E) are present, the code
enables corresponding ethernet and swtich nodes and DSA connections.
For the SFP cage the SFP GPIO controller node and SFP node are also
enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
Enable support for Gigadevice/ISSI flash parts for Versal platform.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are a lot of zynq configurations which can be merged together and use
only one for all. The similar change has been done for ZynqMP by commit
be1b6c32d9 ("arm64: zynqmp: Use zynqmp_virt platform")
Build SPL with u-boot.img for zc706 like this.
export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8
u-boot.img is generic for all boards.
Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable cache commands by default for mtest configuration. It is good to be
able to enable/disable caches when you test memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add DISTRO_DEFAULTS config to versal virt defconfig file which is
suitable for booting general purpose Linux distributions. Remove
other configs which are selected by default by DISTRO_DEFAULTS
configuration.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This allows the user to set $serverip in the environment before
executing a DHCP request. If they do, U-Boot will use that IP rather
than using the IP in the DHCP response.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
U-Boot is configured to build as position independent executable. Enable
relocation of RELA section required to work with different load
addresses.
Signed-off-by: Vishruth <vishruthj@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <probinson@gmail.com>
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
-----BEGIN PGP SIGNATURE-----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=Cgg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc5
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
Define the value as 0x20500000 for lx2160ardb and lx2160aqds.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eMMC HS200 speed mode on Layerscape platforms has not been
supported properly. The eSDHC clock tuning has not been implemented
by now. So disable it until it is supported properly in case of
any potential issues.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
