Since the mdio code got upstreamed it is not possible
to activate network ports on CP110 Master and Slave.
The problem is in mvpp2_base_probe which is called for each
CP110 and it initializes the buffer area for descs and rx_buffers.
This should only happen once though and the bd space is actually
set to 0 after the first run of the function.
This leads to an error when the second CP110 tries the initialization
again and disables all network ports on this CP110.
This patch adds a static variable to check if the buffer area is
initialized only once globally.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
When compiled as a DM_ETH driver, the scm911x driver was reading the MAC
address from the optional EEPROM storage, but failed to copy this to the
platdata struct. Since it was also missing a definition of the
read_rom_hwaddr() function, the generic Ethernet code was dismissing
this MAC address, falling back to a random address or denying to start
at all.
Add an implementation of .read_rom_hwaddr, and refactor the function
reading the ROM address to be called by all interested parties.
This fixes MAC address issues when using the driver in DM_ETH "mode".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patchs adds glue logic to enable designware mac present on
Action Semi based S700 SoC, Configures SoC specific bits.
Undocumented bit that programs the PHY interface select register
comes from vendor source.
It has been tested on Cubieboard7-lite based on S700 SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.
This commits lets proper packets to be transmitted over the network.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds support for Realtek PHY RTL8201F 10/100Mbs
(with variants: RTL8201FN and RTL8201FL) PHYceiver. It is
present on Actions Semi Cubieboard7 board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Update the compatible associated with the STM32 MPU glue
in the DWC ethernet driver.
The supported compatible is the specific "st,stm32mp1-dwmac"
as indicated in Linux binding
Documentation/devicetree/bindings/net/stm32-dwmac.txt
and not the "snps,dwmac-4.20a" only used to the select IP
version.
This glue is implemented in Linux kernel in:
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
For information in stm32mp151.dtsi, the 2 compatibles are
supported:
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
With all the changes in place, add support for DM into the
pcnet driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the common parts of functions out so they can be reused by both
DM and non-DM code paths. The recv() function had to be reworked to
fit into this scheme and this means it now only receives one packet
at a time instead of spinning in an endless loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only name and enetaddr in struct eth_device,
add pointers into the private data which can either point to that non-DM
name or a DM one later on.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only iobase in struct eth_device, add
one into the private data to make DM and non-DM operation possible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Get rid of the global point to private data, and rather pass it
thought dev->priv. Also remove the unnecessary check for lp being
non-NULL, since it is always NULL at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using eth_device priv for this PCI devbusfn, free it
so it could be used for driver private data, and wrap devbusfn
into those driver private data.
Note that using the name dev for the variable is a trick left for
later, when DM support is in place, so dm_pci_virt_to_mem() can be
used with minimal ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove those as they are not needed anymore.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the function at the end of the driver, so we could drop
various forward declarations later. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The private data allocation does not have to be done every time the
NIC is initialized at run time, move the allocation to initialize
function, which means it will be done only once when the driver
starts.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This combination of functions can be replaced with calloc(),
make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current code is horribly complex. Both the RX and TX buffer
descriptors are 16 bytes in size, the init block is 32 bytes in
size, so simplify the code such that the entire private data of
the driver are allocated cache aligned and the RX and TX buffer
descriptors are part of the private data.
This removes multiple malloc calls and cache flushes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use struct pcnet_priv all over the place instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
The index used to iterate over the possible PHYs in axiemac_phy_init was an
unsigned int and decremented. Therefor it was always >= 0 and never exited
the loop.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable PCS autonegotiation if fixed-link node is present in device tree.
This way systems with multiple GEM instances with a combination of
SGMII-fixed and SGMII-PHY will work.
Reported-by: Goran Marinkovic <goran.marinkovic@psi.ch>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As we move towards driver model, it is required to let the FEC driver
know how to properly deal with an Ethernet PHY subnode in the device tree.
For example:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
};
};
};
Currently the PHY node pointer is incorrectly associated with the
Ethernel controller instead of the PHY node itself.
This causes the PHY properties, such as "qca,clk-out-frequency" in
the example above to not get parsed.
Fix this problem by populating the phy_of_node node.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.
This same issue has been already fixed in the kernel by:
commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <o.rempel@pengutronix.de>
Date: Wed Apr 1 11:57:32 2020 +0200
net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply the same fix in the U-Boot driver.
Tested on a i.MX6 Hummingboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Tom Rini <trini@konsulko.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
With all the changes in place, add support for DM into the
pcnet driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the common parts of functions out so they can be reused by both
DM and non-DM code paths. The recv() function had to be reworked to
fit into this scheme and this means it now only receives one packet
at a time instead of spinning in an endless loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only name and enetaddr in struct eth_device,
add pointers into the private data which can either point to that non-DM
name or a DM one later on.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only iobase in struct eth_device, add
one into the private data to make DM and non-DM operation possible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Get rid of the global point to private data, and rather pass it
thought dev->priv. Also remove the unnecessary check for lp being
non-NULL, since it is always NULL at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using eth_device priv for this PCI devbusfn, free it
so it could be used for driver private data, and wrap devbusfn
into those driver private data.
Note that using the name dev for the variable is a trick left for
later, when DM support is in place, so dm_pci_virt_to_mem() can be
used with minimal ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove those as they are not needed anymore.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the function at the end of the driver, so we could drop
various forward declarations later. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The private data allocation does not have to be done every time the
NIC is initialized at run time, move the allocation to initialize
function, which means it will be done only once when the driver
starts.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This combination of functions can be replaced with calloc(),
make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current code is horribly complex. Both the RX and TX buffer
descriptors are 16 bytes in size, the init block is 32 bytes in
size, so simplify the code such that the entire private data of
the driver are allocated cache aligned and the RX and TX buffer
descriptors are part of the private data.
This removes multiple malloc calls and cache flushes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use struct pcnet_priv all over the place instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Instead of doing ethernet device lookup by name every time there
is an MDIO access, pass the driver private data via mdiobus priv
to the MDIO bus accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct eepro100_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the bus_to_phys()/phys_to_bus() macros and calling
that dev, we can substitute dev with udevice when DM support lands
and do minor adjustment to the macros to support both DM and non-DM
operation. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the inline keyword from the static functions, the compiler has a
much better overview and can decide how to inline those functions much
better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Those macros depended on specific variable names to be declared
at their usage sites, fix this by adding an argument to those
macros and also protect the argument with braces.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Pull the MII registration code into a separate function. Moreover,
properly free memory in case any of the registration or allocation
functions fail, so this fixes an existing memleak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Move the functions around in the driver to prepare it for DM conversion.
Drop forward declarations which are not necessary anymore. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Remove all the remaining use of the 'volatile' keyword, as this is
no longer required. All the accesses which might have needed this
use of 'volatile' have been repaired properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add cache invalidation and flushes wherever the DMA descriptors are
written or read, otherwise this driver cannot work reliably on any
systems where caches are enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is replicated in the driver thrice almost verbatim, factor
it out into a separate function and clean it up. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The current eepro100 driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl -f --fix --fix-inplace drivers/net/eepro100.c
This fixes all the remaining errors except a couple of comments which
are longer than 80 characters, all the volatile misuse and all the
camelcase, that needs a separate patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types POINTER_LOCATION -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types PARENTHESIS_ALIGNMENT -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types BRACES -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types SPACING -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is never enabled, last board that used it was ELPPC which
was removed some 5 years ago, so just remove this code altogether.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
We generate a number of helper inline functions to make accesses easier.
However not all permutations of each function will be used and clang
will warn about unused ones. Decorate all of them with __maybe_unused
because of this.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Do not re-read the HW address from the EEPROM on every start of
transfer, otherwise the user will not be able to adjust ethaddr
as needed. Read the address only once, when the card is detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the driver into common and non-DM functionality, so that the
DM support can later re-use the common code, while we retain the
non-DM code until all the platforms are converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of always calling rtl8139_eeprom_delay() with priv->ioaddr,
call it with priv and let the function access priv->ioaddr. This
reduces code duplication and has no impact, since the compiler will
inline this as needed anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros depended on the dev variable being declared wherever
they were used. This is wrong and will not work with DM anyway, so
pass only the PCI BFD into these macros, which fixes the dependency
and prepares them for DM support as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the use of custom static ioaddr variable with common dev->iobase,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace malloc()+memset() combination with calloc(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the device name setting into a separate function, as this
will be shared between DM/non-DM variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add the DP8382X generic PHY registration to the TI PHY init file.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <bod@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
