Replace hardcoded value with defined constant SECTOR_BYTES.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.
Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB
After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
This reverts commit c56ae7519f.
Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.
Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.
Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.
Indeed the SPI controller driver is not aware of the SPI protocol switch.
Further patches will fix the support of Micron QSPI memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
The indentation is misleading here and suggests that the write command
will be only executed in the else clause.
It seems like this is not intended, so fix the indentation to avoid
both compiler warnings and puzzled readers.
Pointed out by GCC 6.2's -Wmisleading-indentation warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The OMAPL138-LCD board uses a NAND chip with a 16 bits bus. Add
support into the davinci driver for 16 bit bus NAND chips.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the description of the Toshiba TC58NVG2S0H SLC nand to the nand_ids
table so we can use the NAND ECC infos and the ONFI timings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds support for the Macronix MX66U51235F,
MX66L1G45G and Micron MT25QU02G, MT25QL02G flash parts.
Signed-off-by: Radu Bacrau <dumitru.bacrau@intel.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Radu Bacrau <radu.bacrau@gmail.com>
[Update proper commit header and 80-line cut on body]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Somehow an int returning function without a return statement sneaked
in, fix it.
Also fix some whitespace damage on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
s25fs512s and s25fl512s_256k have common id information
till 5 bytes and 6th byte have different family id
like FS and FL-S as 0x81 and 0x80.
Reported-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
- fix single line comments
- remove unneeded spaces
- ascending order of include files
- rename SPI DATAFLASH to dataflash
- rename SPI DataFlash to dataflash
- return NULL replaced with error code
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch fixed the add_dataflash return logic,
so-that it can handle both jedec and older chips
same as Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Flash id detection should be the first step to enumerate
the connected flash on the board, once ie done checking
with respective id codes locally in the driver all this
should be part of jedec_probe instead of id detection and
validated through flash_info{} table separatly.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
dataflash doesn't require options, memory_map from spi.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_write_bar-> write_bar
spi_flash_write_bar -> read_bar
spi_flash_cmd_wait_ready -> spi_flash_wait_till_ready
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Use small 'd' in s25s512s ext_jedec
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
For readability use small letter's with flash name.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Remove unneeded/non-meaningful commit message on
params and flash.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
For this:
- Removed spansion_s25fss_disable_4KB_erase code
- Add SECT_4K for S25FS512S chip
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add Spansion S25FS256S_64K spi flash to the list of spi_flash_ids.
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
INFO6 is for tabulating 6 byte flash parts, Ex: S25FS256S_64K
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
So, now SPI_FLASH_ID_MAX_LEN is 6 bytes useful for
few spansion flash families S25FS-S
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Add id length of 5 bytes numerical value to macro.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Rename nr_sectors as n_sectors to sync with Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
- Proper tabs spaces
- Removed unnecessary
- Add comments in spi_flash_info members
- Add comments for spi_flash_info.flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of extracting id's separately better
to use JEDEC_MFR|ID for code simplicity.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Simplify the flash_lock ops detection code and added
meaningful comment.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
INFO macro make flash table entries more adjustable like
adding new flash_info attributes, update ID length bytes
and so on and more over it will sync to Linux way of defining
flash_info attributes.
- Add JEDEC_ID
- Add JEDEC_EXT macro
- Add JEDEC_MFR
- spi_flash_params => spi_flash_info
- params => info
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Clear ecc ON bit while sending read command as all types
of read command(like reading spare) doesnt need ECC to be
enabled. It has been anyway taken care in other places
whereever required using arasan_nand_enable_ecc().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
move the UBI config options into Kconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch moves flags macro's to respective member position on
spi_flash_params{}, for better readabilty and finding the
respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add CONFIG_SPI_FLASH_USE_4K_SECTORS in spi_flash code from header file.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SECT_32K never used anywhere in the code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
e_rd_cmd is maintained separately for fastest read command code,
since the read commands are computed normally this e_rd_cmd
is not required in spi_flash_params table.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fastest read command code look for fastest read command
taking inputs from spi->mode_rx and flags from param table
and controller mode_rx is always been a priority.
Since mode_rx is always set from controller side this optimized
code doesn't require much and this code required exctra overhead like
1) Maintain e_rx_cmd in param table
2) Maintain mode_rx in spi_slave {}
Hence removed this code, and look for read command from normal
spi->mode from spi_slave{} and params->flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Currently the command buffer gets allocated with a size of 32 bytes.
This causes warning messages on systems with cache lines bigger than
32 bytes:
CACHE: Misaligned operation at range [9df17a00, 9df17a20]
Define command buffer to be at least 32 bytes, but more if cache
line is bigger.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data") the assignment of mtd->priv was removed
but was not replaced. This adds the required nand_set_controller_data()
call.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add a full-id entry for the H27QCG8T2E5R‐BCF NAND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add timeout to onenand_wait ready loop as it hangs here indefinitely
when chip not present. Once there, do the same for onenand_bbt_wait
as well (note: recent Linux driver code does the same)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Booting a payload out of NAND FLASH from the SPL is a crux today, as
it requires hard partioned FLASH. Not a brilliant idea with the
reliability of todays NAND FLASH chips.
The upstream UBI + UBI fastmap implementation which is about to
brought to u-boot is too heavy weight for SPLs as it provides way more
functionality than needed for a SPL and does not even fit into the
restricted SPL areas which are loaded from the SoC boot ROM.
So this provides a fast and lightweight implementation of UBI scanning
and UBI fastmap attach. The scan and logical to physical block mapping
code is developed from scratch, while the fastmap implementation is
lifted from the linux kernel source and stripped down to fit the SPL
needs.
The text foot print on the board which I used for development is:
6854 0 0 6854 1abd
drivers/mtd/ubispl/built-in.o
Attaching a NAND chip with 4096 physical eraseblocks (4 blocks are
reserved for the SPL) takes:
In full scan mode: 1172ms
In fastmap mode: 95ms
The code requires quite some storage. The largest and unknown part of
it is the number of fastmap blocks to read. Therefor the data
structure is not put into the BSS. The code requires a pointer to free
memory handed in which is initialized by the UBI attach code itself.
See doc/README.ubispl for further information on how to use it.
This shares the ubi-media.h and crc32 implementation of drivers/mtd/ubi
There is no way to share the fastmap code, as UBISPL only utilizes the
slightly modified functions ubi_attach_fastmap() and ubi_scan_fastmap()
from the original kernel ubi fastmap implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To support UBI in SPL we need a simple NAND read function. Add one to
nand_spl_simple and keep it as simple as it goes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
flash_full_status_check() checks bit XSR.7 on Intel chips. This
should be done by only checking bit 7 and not by comparing the
whole status byte or word with 0x80.
This fixes the non-working block erase in the pflash emulation
of Qemu when used with the MIPS Malta board. MIPS Malta uses x32
mode to access the pflash device. In x32 mode Qemu mirrors the
lower 16 bits of the status word into the upper 16 bits. Thus
the CFI driver gets a status word of 0x8080 in x32 mode. If
flash_full_status_check() uses flash_isequal(), then it polls for
XSR.7 by comparing 0x8080 with 0x80 which never becomes true.
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This empty line should not be there. Remove it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND chips are supposed to expose their capabilities through advanced
mechanisms like READID, ONFI or JEDEC parameter tables. While those
methods are appropriate for the bootloader itself, it's way to
complicated and takes too much space to fit in the SPL.
Replace those mechanisms by a dumb 'trial and error' mechanism.
With this new approach we can get rid of the fixed config list that was
used in the sunxi NAND SPL driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Split the 'load page' and 'read page' logic in 2 different functions so
we can later load the page and test different ECC configs without the
penalty of reloading the same page in the NAND cache.
We also move common setup to a dedicated function (nand_apply_config()) to
avoid rewriting the same values in NFC registers each time we read a page.
These new functions are passed a pointer to an nfc_config struct to limit
the number of parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
check_value_xxx() helpers are using a 1ms delay between each test, which
can be quite long for some operations (like a page read on an SLC NAND).
Since we don't have anything to do but to poll this register, reduce the
delay between each test to 1us.
While we're at it, rename the max_number_of_retries parameters and the
MAX_RETRIES macro into timeout_us and DEFAULT_TIMEOUT_US to reflect that
we're actually waiting a given amount of time and not only a number of
retries.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Use CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND value instead of trying to guess
where the redundant u-boot image is based on simple (and most of the time
erroneous) heuristics.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
# Conflicts:
# drivers/mtd/nand/sunxi_nand_spl.c
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.
Add an extra Kconfig option to specify the offset of the redundant u-boot
image.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
The SYS_NAND_U_BOOT_OFFS is quite generic, but the Kconfig entry is forced
to explicitly depend on platforms that are not already defining it in their
include/configs/<board>.h header.
Add the SYS_NAND_U_BOOT_LOCATIONS option, make the SYS_NAND_U_BOOT_OFFS
depends on it, remove the dependency on NAND_SUNXI and make it dependent
on SPL selection.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The sunxi SPL NAND controller driver supports use 'BootROM'-like configs,
that is, configs where the ECC bytes and real data are interleaved in the
page instead of putting ECC bytes in the OOB area.
Doing that has several drawbacks:
- since you're interleaving data and ECC bytes you can't use the whole page
otherwise you might override the bad block marker with non-FF bytes.
- to solve the bad block marker problem, the ROM code supports partially
using the page, but this introduces a huge penalty both in term of read
speed and NAND memory usage. While this is fine for rather small
binaries(like the SPL one which is at maximum 24KB large), it becomes
non-negligible for the bootloader image (several hundred of KB).
- auto-detection of the page size is not reliable (this is in my opinion
the biggest problem). If you get the page size wrong, you'll end up
reading data at a different offset than what was specified by the caller
and the reading may succeed (if valid data were written at this address).
For all those reasons I think it's wiser to completely remove support for
'syndrome' configs. If we ever need to support it again, then I'd recommend
specifying all the config parameters through Kconfig options.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This needs to be set to avoid a fatal error when ECC is used.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This uses the wrote base register value. Fix it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
Updates the NAND code to match Linux v4.6. The previous sync was from
Linux v4.1 in commit d3963721d9.
Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
This change is part of the Linux 4.6 sync. It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Commit ad4f54ea86 ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Serial number, vendor id and page size are added for QSPI flash
common on both LS1012AQDS and LS1012ARDB i.e. S25FS512SDSMFI011.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Detect a FIT when loading from SPI and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Scott Wood <oss@buserror.net>
PIC32 internal flash devices are parallel NOR flash divided into
number of banks to allow erase-programming in one while fetch and
execution continues on other. As the flash banks are memory mapped
stored code can be executed directly from flash (XIP), also there
is additional hardware logic to prefetch and cache contents to
improve execution performance. These flash can also be used to
store user data (like environment).
Flash erase and programming are handled by on-chip NVM controller.
Driver implemented driver model but MTD is not really support.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The S25FS-S family physical sectors may be configured as a hybrid
combination of eight 4-kB parameter sectors at the top or bottom
of the address space with all but one of the remaining sectors
being uniform size.
The default status of the flash is in this hybrid architecture.
The parameter sectors and the uniform sectors have different erase
commands.
This patch disable the hybrid sector architecture then the flash will
has uniform sector size and uniform erase command.
This configuration is temporary, the flash will revert to hybrid
architecture after power on reset.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
get_timer() returns an unsigned 64-bit value, but is currently assigned to
a signed 32-bit variable. Due to sign extension and data truncation, this
causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and
incorrectly) fire for about 50% of all time values, based on whether bit
31 is set. In sandbox at least, this causes the test to pass or fail based
on system uptime, as opposed to time since the U-Boot binary was started.
Fixes: 4efad20a17 ("sf: Update status reg check in spi_flash_cmd_wait_ready")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Set free_count to zero before walking through ai->erase list
in wl_init().
As U-Boot has no workqueue/threads, it immediately calls
erase_worker(), which increase for each erased block
free_count. Without this patch, free_count gets after
this initialized to zero in wl_init(), so the free_count
variable always has the maybe wrong value 0.
Detected this behaviour on the dxr2 board, where the
UBI fastmap gets not written when attaching/dettaching
on an empty NAND. It drops instead the error message:
could not find any anchor PEB
With this patch, fastmap gets written on dettach.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Unlock current sector instead of sector 0 before buffered write.
[Patch subject and commit text slightly reworded, Stefan]
Signed-off-by: Rouven Behr <u-boot@behr-iss.de>
Signed-off-by: Stefan Roese <sr@denx.de>
After writing data to flash space, next instruction is checking if flash
controller is busy writing to the flash memory. Memory barrier is required here
to avoid transaction re-ordering for data write and busy status check.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Otherwise flash remains in read status mode and it's not possible
to access data on flash.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The 64-bit compiler (ex. aarch64) emits "warning: cast from pointer
to integer of different size".
Make it work with 64bit DMA address while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1e90d9fd (sf: Move read_id code to sf_ops)
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a little more debugging to help when things go wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
The allocation size is reduced from what was introduced from the
Linux kernel, as U-boot uses the statically allocated nand_info
instead of needing to dynamically allocate an mtd_info instance.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Correct some pointer math in initialization. An offset was added
to a struct-typed pointer instead of one casted to a byte-size,
resulting in a much larger offset than intended.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Correct a null pointer dereference in board_nand_init(). Zeroed
memory was allocated, then immediately dereferenced. The
dereference is completely removed, since this pointer is later
initialized in alloc_nand_resources.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Fix error handling for mxs_nand_init.
The original error handling is wrong for err2 and err1.
Should first free desc[x], then free desc.
This patch also correctly handle err3, should use
MXS_DMA_CHANNEL_AHB_APBH_GPMI0 as the check point.
Cc: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Also if minimum ecc requirment is bigger then what we support, then just
use our maxium pmecc support.
But it is not safe, so we'll output a warning about this.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
1. add the pmecc register mapping for sama5d2.
2. add the pmecc error location register mapping for sama5d2.
3. add some new field that is different from old ip.
4. add sama5d2 pmecc ip version number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
As atmel_nand_ecc.h is sync with v4.1 kernel, which adds the
PMECC_OOB_RESERVED_BYTES. So use it in the driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Also align the open parenthesis.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function currently searches the entire device tree for a node that
it thinks is relevant. But the node is known and is passed in. Correct the
code and enable it only with driver model, since only driver-model boards
will use it.
This avoids bringing in a large number of strings from fdtdec.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
For SPL we don't really need sprintf() and with tiny-printf this is not
available. Allow this to be dropped in SPL when using tiny-printf.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
While setting quad bit on spansion, macronix code
is writing only particular quad bit this may give
wrong functionality with other register bits,
So this patch fix the issue where it with write
previous read reg status along particular quad bit.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One macronix quad bit set using SR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
One spansion quad bit set using CR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Peter Pan <peterpandong@micron.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Tab space
- Place all read commands at one place.
- Re-arrange write commands.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use direct call to device_remove instead of exctra
spi_flash_remove defination.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
bar_end gives more meaningfull compared to bank_end and
spi_flash_write_bar uses bar_end so replaced bank_end with
bar_end in spi_flash_read_bar
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_read_cmds_array is used locally in
spi_flash_scan, so move array to locally used
function instead of defining global array.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like
SPI_TX_BP => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For better code readabilty, get the spi pointer from
spi_flash{} locally and use it instead of direct
dereferring spi pinter as flash->spi->*
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
drivers/mtd/ubi/io.c:1354:3: error: 'dump_len' undeclared (first use in
this function)
dump_len = max_t(int, 128, len - i);
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Skip erase if the sector is blank. The sector erase is slow, and
may take 0.7 sec typically or up to 3 sec worst-case.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
If the erase fails, fail_addr might indicate exactly which block
failed. If fail_addr = MTD_FAIL_ADDR_UNKNOWN, the failure was not
at the device level or was not specific to any particular block.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Erase is an asynchronous operation. Device drivers are supposed
to call instr->callback() whenever the operation completes, even
if it completes with a failure.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Initialize instr.mtd in flash_erase(). This fixes the system
hang issue when CONFIG_MTD_PARTITIONS is selected.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Since all spi-flash core operations are moved into
sf_ops.c then it's better to renamed as spi-flash.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used static for file-scope functions in sf_probe.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_slave is a spi pointer in spi_flash{} then assign
spi_slave{} pointer to flash->spi and remove spi_slave
pointer argument to
- spi_flash_probe_slave
- spi_flash_scan
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For assigning read_bar commands in spansion case, break
is missing this patch add that break.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SST parts added on sf_params.c supports both SST_WR which consits
of both BP and WP and there is a spi controller ich which supports
only BP so the relevent _write hook set based on "slave->op_mode_tx"
hence there is no respective change required from flash side hance
removed these.
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Removed unneeded header includes in sf_ops and sf_probe
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Using macro's for flash power up read-only access code
leads wrong behaviour hence use idcode0 for runtime
detection, hence the flash which require this functionality
gets detected at runtime.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Most of the register access function are static,
so used simple name to represent each.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch removes unneeded ifdef and fixed accordingly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use static for file-scope functions and removed
them from header files.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Move bar read code below the bar write hance both
at once place, hence it easy for #ifdef macro only
once and readable.
- Move read_cmd_array at top
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
read_id code is related to spi_flash stuff
hence moved to sf_ops.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Intension is that sf_ops should deals all spi_flash
related stuff and sf_probe (which should renamed future)
should be an interface layer for spi_flash versus spi drivers.
sf_ops => spi_flash interface
sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Rename spi_flash_validate_params to spi_flash_scan
as this code not only deals with params setup but
also configure all spi_flash attributes.
And also moved all flash related code into
spi_flash_scan for future functionality addition.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fix erase and write error code, which should be "protected".
From the "Embedded Peripherals IP User Guide" of Altera,
The "Illegal write" flag indicates that a write instruction is
targeting a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled a write instruction.
The "Illegal erase" flag indicates that an erase instruction has
been set to a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled the erase instruction.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add lock() and unlock() mtd ops to altera_qspi.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is follow up patch based on
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
to update function pointers for DM.
Using post_bind is not ideal but it is one on current option what can be
used. Variable reloc_done has to be used do not call relocation after
every bind. Maybe new core functions should be introduced for this case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
flash->flags for SST flash should be updated for both DM and non-DM
flash drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We should check the return value from spi_flash_cmd_read_status() and
propagate it in the case of error.
This fixes a defect caught by Coverity.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
SST SPI NOR flash has the same locking programming bits
as ST Micro - added support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
[Minor change on commit message]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The relevent boards which used this driver got zapped
in previous release and the driver is never used in the
code and also it doesn't use/do any spi-flash operations.
Commit details for relevent removed boards:
"ARM: at91: remove non-generic boards"
(sha1: f6b42c1403)
Cc: Tom Rini <trini@konsulko.com>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
commit c3c016c "sf: Add SPI NOR protection mechanism" introduced
flash_lock()/flash_unlock()/flash_is_locked() methods for SPI flash,
but not every flash driver supplies these. We should test these
methods against NULL before actually calling them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The current error message in get_part if CONFIG_MTDPARTS is disabled is
"offset is not a number" which is confusing and doesn't help at all.
Change that for something that might give a hint on what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Altera Generic Quad SPI Controller support. The controller
converts SPI NOR flash to parallel flash interface. So it is
not like other SPI flash, but rather like CFI flash.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Implement a Memory Technology Device (MTD) uclass. It should
include most flash drivers in the future. Though no uclass ops
are defined yet, the MTD ops could be used.
The NAND flash driver is based on MTD. The CFI flash and SPI
flash support MTD, too. It should make sense to convert them
to MTD uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Many SPI flashes have protection bits (BP2, BP1 and BP0) in the
status register that can protect selected regions of the SPI NOR.
Take these bits into account when performing erase operations,
making sure that the protected areas are skipped.
Tested on a mx6qsabresd:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> sf protect lock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
offset 0x3f0000 is protected and cannot be erased
SF: 65536 bytes @ 0x3f0000 Erased: ERROR
=> sf protect unlock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
SF: 65536 bytes @ 0x3f0000 Erased: OK
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
[re-worked to fit the lock common to dm and non-dm]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add the SPI NOR protection mechanism from the kernel.
This code is based on the work from
Brian Norris <computersforpeace@gmail.com>
Here is the commit details:
"mtd: spi-nor: refactor block protection functions"
(sha1: 62593cf40b23b523b9fc9334ca61ba6c595ebb09)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch changes the cword union to use specific length types that are
architecture indepented.
This patch also renames the members of the cword union to represent
their usage, i.e.:
c -> w8
s -> w16
l -> w32
ll -> w64
Where "w" stands for "width" in bits.
I discovered this problem when enabling CFI flash on vexpress64.
cword.l was an unsigned long int, but it was intended to be 32 bits wide.
Unfortunately, it's 64-bits wide on a 64-bit system, meaning that a
64-bit system fails when attempting to use 32-bit wide CFI flash parts.
Similar problems also existed with the other cword sizes.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The PEB array is an array of __be32, so let's fix the
scan_pool() prototype accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Heiko Schocher <hs@denx.de>
sync with linux v4.2
commit 64291f7db5bd8150a74ad2036f1037e6a0428df2
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Aug 30 11:34:09 2015 -0700
Linux 4.2
This update is needed, as it turned out, that fastmap
was in experimental/broken state in kernel v3.15, which
was the last base for U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
This patch adds flag status register reading support to
spi_flash_cmd_wait_ready.
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Hou Zhiqiang <B48286@freescale.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Current flash wait_ready logic is not modular to add new
register status check, hence updated the status check for
adding few more register checks in future.
Below are the sf speed runs with 'sf update' on whole flash, 16MiB.
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 59.564s, speed 289262 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 62.549s, speed 275036 B/s
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 61.276s, speed 284359 B/s
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use the flash->flags for generic usage, not only for dm-spi-flash,
this will be used for future flag additions.
[Correct the spi flash flags detect logic]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Optimized spi-flash bar writing code and also removed
unnecessary bank_sel in read_ops.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add spi_flash_read_bar function for reading bar and
discovering bar commands at probe time.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
If computed bank_sel is same as flash->bank_curr which is
computed at probe time, then return the bank_sel instead of zero.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Added support for IS25LP128 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Added support for IS25LP064 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Added support for IS25LP032 flash part.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This resyncs the driver changes with the Linux version of the
driver. The driver received some feedback in the LKML and got
recently acceppted, the latest version can be found here:
https://lkml.org/lkml/2015/9/2/678
Notable changes are:
- On ECC error, reread OOB and count bit flips in OOB too.
If flipped bits are below threshold, also return an empty
OOB buffer.
- Return the amount of bit flips in vf610_nfc_read_page.
- Use endianness aware vf610_nfc_read to read ECC status.
- Do not enable IDLE IRQ (since we do not operate with an
interrupt service routine).
- Use type safe struct for buffer variants (vf610_nfc_alt_buf).
- Renamed variables in struct vf610_nfc (column and page_sz)
to reflect better what they really representing.
The U-Boot version currently does not support RAW NAND write
when using the HW ECC engine.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Scott Wood <scottwood@freescale.com>
Messages on corrected bit-flips are not really useful,
as bit-flips are perfectly normal. Let's avoid cluttering
the console and make them debug.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
AT26DF081A is the spi flash type of TWR-MEM(SCH-26248) card.
We can access the flash through DSPI2 on LS1021ATWR board.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
We know when u-boot is written to its own partition, in this case the
layout always is:
eb 0 spl
eb 1 spl-backup
eb 2 u-boot
eb 3 u-boot-backup
eb: erase-block
So if we cannot load u-boot from its primary offset we know exactly where
to look for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Check maximum ecc strength for each platfrom to avoid the calculated ecc
exceed the limitation.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Han Xu <b45815@freescale.com>
Tested-By: Tim Harvey <tharvey at gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:
- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
not supporting the BCH8 HW ECC (FSMC_VER8)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <scottwood@freescale.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:
4519668 mtd/nand/ubi: assortment of alignment fixes
This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.
Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your config header:
#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH
And use the command "nandecc bch4" to select this ECC scheme upon runtime.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.
Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.
Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.
This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Auto detect the nand configuration parameters, like the BROM does.
This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.
The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.
Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.
This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.
Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We are using dma, so we should flush the cache before starting the dma,
and invalidate it once the dma is done.
Things are working without this by mostly luck, but lets not rely on that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Turn off the nand and dma clocks when we're done with the nand, this
puts the nand and dma controllers back into a clean state for when the
kernel boots.
Without this the kernel will not boot properly when it is built with
dma-controller support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In syndrome mode we set the NFC_SEQ bit in the command register, so the
spare-area register is not used. Also the value currently being written is
actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE"
not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE.
So the current code only serves to confuse the user -> remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There is no need to reset the nand chip for every ecc-block read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
nand_spl_load_image() always gets called with either CONFIG_SYS_TEXT_BASE
or spl_image.load_addr as destination, both of which are properly aligened,
and have plenty of space for "overshooting" up to
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes, as we read in
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes chunks.
This saves CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE (typically 1k) in
SPL size, which is a lot on the total 24k we have.
Note this changes the dma destination from SRAM to DRAM, so this patch
updates the DDMA_DST_TYPE bits in the dma controller cfg0 reg accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Since commit 2580a2a7e7 ("mtd: nand: Increase max sizes of OOB and
Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build
with the following error message:
arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big
They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer
as static data:
static uint8_t page_buffer[NAND_MAX_PAGESIZE];
This buffer required 8KB in .bss section before that commit and now
it has been increased to 16KB. Given limited code/memory size for SPL,
it is not a good idea to allocate a page buffer statically. In the
first place, the load address 'dst' can be used as a page buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
Follow linux dma flow:
Before DMA read, be sure to invalidate the cache over the address
range of DMA buffer to prevent cache coherency problems.
After DMA read, invalidate dcache again.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:
http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html
Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:
https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html
Otherwise it will not compile.
Tested on the Marvell Armada XP DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Update the NAND code to match Linux v4.1. The previous sync was
from Linux v3.15 in commit 4e67c57125.
CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout. Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)
This layout is matching the lpc32xx NAND SLC Linux Kernel driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition
The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Make the support for 4K subpage I/O on a SPI NOR flash configurable.
A board which requires the SPI NOR to be accessed in larger 32KiB
or 64KiB pages can disable the 4K subpage support, but by default,
the support for 4K subpage I/O is enabled. The functionality of this
option is the same as CONFIG_MTD_SPI_NOR_USE_4K_SECTORS in Linux.
This is extremely useful in case one uses UBI on a SPI NOR flash.
UBI needs at least 15k EBs and can not work on a flash which uses
4k ones, so disabling the support for 4k subpages lets UBI work on
such flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Disable subpage writes as we do not provide ecc->hwctl.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.
This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).
I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
remove unneeded udelay() in this function, as we use
the dev_ready pin.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Since commit 09c3280754 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).
Signed-off-by: Stefan Agner <stefan@agner.ch>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
the special handling of OOB (spareonly).
Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.
However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.
Signed-off-by: Stefan Agner <stefan@agner.ch>
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Freeing allocated memory to priv before returning
from the function
Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.
This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).
I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This printf() should have a newline at the end. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers. Fix the resulting array overflow.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.
The SPL framework is supported.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add support for on-flash bad block table. This makes U-Boot handle an existing
BBT correctly.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Testing showed, that commands like STATUS made the buffer dirty
when executed with NFC_SECSZ set to the page size. It looks
like the controller transfers bogus data when this register
is configured. When setting it to 0, the buffer does not get
altered while the status command still seems to work flawless.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The driver tries to re-use the page buffer by storing the page
number of the current page in the buffer. The page is only read
if the requested page number is not currently in the buffer. When
a block is erased, the page number is marked as invalid if the
erased page equals the one currently in the cache. However, since
a erase block consists of multiple pages, also other page numbers
could be affected.
The commands to reproduce this issue (on a written page):
> nand dump 0x800
> nand erase 0x0 0x20000
> nand dump 0x800
The second nand dump command returns the data from the buffer,
while in fact the page is erased (0xff).
Avoid the hassle to calculate whether the page is affected or not,
but set the page buffer unconditionally to invalid instead.
Signed-off-by: Stefan Agner <stefan@agner.ch>
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years. If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling. This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.
U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Add nand_verify() and nand_verify_page_oob(). nand_verify() verifies
NAND contents against an arbitrarily sized buffer using ECC while
nand_verify_page_oob() verifies a NAND page's contents and OOB.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
The 'nandecc sw' command selects a software-based error correction
algorithm. By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm. Allow a user to be specific e.g.
# nandecc sw <hamming|bch8>
where 'hamming' is still the default.
Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
to a hardware-based ECC scheme---a little strange when the user
has requested 'sw' ECC.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Commit fb384c4720 introduced the use of
WAIT0 pin for determining whether the NAND is ready or not. This only
works if all NAND chips are connected to WAIT0. If some chips are
connected to the other available pin WAIT1, nand_wait() does not really
wait and prints a WARN_ON message.
This patch allows the board to provide configuration of which chip is
connected to which WAITx signal. For example, one can define in
include/configs/foo.h:
#define CONFIG_NAND_OMAP_GPMC_WSCFG 0,0,1,1
This would mean that chips using to CS0 and 1 are connected to WAIT0 and
chips with CS2 and 3 are connected to WAIT1.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Vokáč <michal.vokac@comap.cz>
Cc: Tom Rini <trini@ti.com>
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL). There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.
It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:
[1] It is impossible to share CONFIG options across the images.
If you change the configuration of Main image, you often have to
adjust some SPL configurations correspondingly. Currently, we
cannot handle the dependencies between them. It means one of the
biggest advantages of Kconfig is lost.
[2] It is too painful to change both ".config" and "spl/.config".
Sunxi guys started to work around this problem by creating a new
configuration target. Commit cbdd9a9737 (sunxi: kconfig: Add
%_felconfig rule to enable FEL build of sunxi platforms.) added
"make *_felconfig" to enable CONFIG_SPL_FEL on both images.
Changing the configuration of multiple images in one command is a
generic demand. The current implementation cannot propose any
good solution about this.
[3] Kconfig files are getting ugly and difficult to understand.
Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.
[4] The build system got more complicated than it should be.
To adjust Linux-originated Kconfig to U-Boot, the helper script
"scripts/multiconfig.sh" was introduced. Writing a complicated
text processor is a shell script sometimes caused problems.
Now I believe the "single .config" will serve us better. With it,
all the problems above would go away. Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much. Anyway, this is what we do now in
scripts/Makefile.spl.
I admit my mistake with my apology and this commit switches to the
single .config configuration.
It is not so difficult to do that:
- Remove unnecessary processings from scripts/multiconfig.sh
This file will remain for a while to support the current defconfig
format. It will be removed after more cleanups are done.
- Adjust some makefiles and Kconfigs
- Add some entries to include/config_uncmd_spl.h and the new file
scripts/Makefile.uncmd_spl. Some CONFIG options that are not
supported on SPL must be disabled because one .config is shared
between SPL and U-Boot proper going forward. I know this is not
a beautiful solution and I think we can do better, but let's see
how much we will have to describe them.
- update doc/README.kconfig
More cleaning up patches will follow this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch c316f577b4 breaks
siemens boards because prefetch mode is not enabled.
I assume it breaks other boards as well that don't use
prefetch.
This patch sets read_buf to nand_read_buf if
NAND_OMAP_GPMC_PREFETCH is not defined.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
CC: Daniel Mack <zonque@gmail.com>
CC: Guido Martínez <guido@vanguardiasur.com.ar>
CC: Tom Rini <trini@ti.com>
CC: Heiko Schocher <hs@denx.de>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
As the PMECC hardware has different version. In SAMA5D4 chip, the PMECC ip
can generate 0xff pmecc ECC value for all 0xff sector.
According to this, add PMECC version check, if it's SAMA5D4 then we always
let PMECC hardware to correct it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
Enable GPMC's prefetch feature for NAND access. This speeds up NAND read
access a lot by pre-fetching contents in the background and reading them
through the FIFO address.
The current implementation has two limitations:
a) it only works in 8-bit mode
b) it only supports read access
Both is easily fixable by someone who has hardware to implement it.
Note that U-Boot code uses non word-aligned buffers to read data into, and
request read lengths that are not multiples of 4, so both partial buffers
(head and tail) have to be addressed.
Tested on AM335x hardware.
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Daniel Mack <zonque@gmail.com>
[trini: Make apply again, use 'cs' fix pointed out by Guido]
Signed-off-by: Tom Rini <trini@ti.com>
Currently, "nand scrub" runs chip->scan_bbt at the end of
nand_erase_opts() even if NAND_SKIP_BBTSCAN flag is set.
It violates the intention of NAND_SKIP_BBTSCAN.
Move NAND_SKIP_BBTSCAN flag check to nand_block_checkbad() so that
chip->scan_bbt() is never run if NAND_SKIP_BBTSCAN is set.
Also, unset NAND_BBT_SCANNED flag instead of running chip->scan_bbt()
right after scrub. We can be lazier here because the BBT is scanned
at the next call of nand_block_checkbad().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Commit 35c204d8a9 (nand: reinstate lazy bad block scanning)
broke NAND_BBT_USE_FLASH feature.
Its git-log claimed that it reinstated the change as by commit
fb49454b1b ("nand: reinstate lazy bad block scanning"), but it moved
"chip->options |= NAND_BBT_SCANNED" below "chip->scan_bbt(mtd);".
It causes recursion if scan_bbt does not find a flash based BBT
and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Reinstate commit ff49ea8977 (NAND: Mark the BBT as scanned prior to
calling scan_bbt.).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rostislav Lisovy <lisovy@merica.cz>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Since commit ff94bc40af (mtd, ubi, ubifs: resync with Linux-3.14),
the "nand scrub" command has not been working.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).
In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the necessary flash entry for the Spansion S25FL164K
flash. Tested on Marvell 88F6218 based design.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Added S25FL116K flash and tested on Marvell 88F6281 based system.
Signed-off-by: Adnan Ali <adnan.ali@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for SST25WF040B-40I-SN flash.
Tested on T1024QDS board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed ramtron driver since the EMK boards are
no longer been active, and these are the only boards
used this flash driver.
Commit details for EMK zap:
"ppc/arm: zap EMK boards"
(sha1: d58a9451e7)
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Enabled byte program support for sst flashes in sf.
Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.
A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Currently if SST flash advertises SST_WP flag in the params table
the word program command (ADh) with auto address increment will be
used for the flash write op. However some SPI controllers do not
support the word program command (like the Intel ICH 7), the byte
programm command (02h) has to be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
At present SECT_4K is the same as SST_WP so we cannot tell these apart. Fix
this so that the table in sf_params.c can be used correctly.
Reported-by: Jens Rottmann <Jens.Rottmann@adlinktech.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Few of the spi controllers are only supports array slow
read which is quite different behaviour compared to others.
So this fix on sf will correctly handle the slow read supported
controllers.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
'eccstat' array elements might be used uninitialized
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.
Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:
Without NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.947 seconds, 2947 ticks
With NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.795 seconds, 2795 ticks
So an increase of approx. 5%.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.
Patch has been tested on a Colibri VF61 module.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc. Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices. The device parameters detected
during nand_scan_ident() are more trustworthy.
This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().
CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux. Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").
Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
ff94bc40af "mtd, ubi, ubifs: resync with Linux-3.14"
introduced the writebufsize field in struct mtd_info, which
is not initialized in the cfi_flash driver, which leads in
not working ubi on cfi flashes. Fix it
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.
Signed-off-by: Marek Vasut <marex@denx.de>
- make omap_spl_dev_ready static
- make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@ti.com>
For various reasons (design, errata) boards may need to implement their
own versions of these accessors. So in the case of
CONFIG_CFI_FLASH_USE_WEAK_ACCESSOR mark the functions as weak. In the
normal case mark them as static to allow for better optimization.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[trini: Reword commit message]
Signed-off-by: Tom Rini <trini@ti.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
We want the SPI flash probing feature to operate as a standard driver.
Add a driver for the basic probing feature used by most boards. This
will be activated by device_probe() as with any other driver.
The 'sf probe' command currently keeps track of the SPI slave that it
last used. This doesn't work with driver model, since some other driver
or system may have probed the device and have access to it too. On the
other hand, if we try to probe a device twice the second probe is a nop
with driver model.
Fix this by searching for the matching device, removing it, and then
probing it again. This should work as expected regardless of other device
activity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.
CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust spi_flash_probe_slave() to return an error value instead of a
pointer so we get the correct error return.
Have the caller allocate memory for spi_flash to simplify error handling,
and also so that driver model can use its existing allocated memory.
Add a spi.h include in the sf_params file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Some files are using SPI functions but not explitly including the SPI
header file. Fix this, since driver model needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported. It is necessary to detect some
types of ONFi-compliant devices. Without it, the error message
"unsupported command received 0x5" is shown.
Let's support this command on the Denali NAND controller driver.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.
Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.
In addition, unnecessary clear_interrupts() should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Partially revert commit 0d01f66d23 (CFI: cfi_flash write fix for AMD
legacy).
flash_full_status_check() used to skip status register parsing when
flash_status_check() returns OK. This is wrong since flash_status_check()
must return OK for other status bits to be valid.
Cc: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP.
This driver requires two CONFIG macros:
- CONFIG_SPL_NAND_DENALI
Define to enable this driver.
- CONFIG_SYS_NAND_BAD_BLOCK_POS
Specify bad block mark position in the oob space. Typically 0.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
Commit 3eb3e72a3f (nand/denali: Adding Denali NAND driver support)
introduced some new options, and some of them were documented by
commit f9860cf081 (nand/denali: Document CONFIG symbols).
This commit allows users to enable/disable them via Kconfig
with more detailed help docs.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
At present sandbox has its own table of supported SPI flash chips. Now that
the SPI flash system is fully consolidated and has its own list, sandbox
should use that.
This enables us to expand the number of chips that sandbox supports.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
To add the Denali NAND driver support into U-Boot.
This driver is leveraged from Linux with commit ID
fdbad98dff8007f2b8bee6698b5d25ebba0471c9. For Denali
controller 64 variance, you need to declare macro
CONFIG_SYS_NAND_DENALI_64BIT.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The ioread16_rep() and iowrite16_rep() implementations are U-Boot specific
and have been introduced with the Linux MTD v3.14 sync. While introducing
these functions, the length for the loop has been miscalculated. The ">> 1"
is already present in the caller. So lets remove it in the function.
Tested on omap3_ha.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
OMAP GPMC driver used with some NAND Flash devices
(e.g. Spansion S34ML08G1) causes that U-boot shows
hundreds of 'nand: bit-flip corrected' error messages.
Possible cause was discussed in the mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html
The issue was partially fixed with the cc81a5291910d7a.git
however this has to be done to fix the SPL.
The original author of the code is Belisko Marek
<marek.belisko@gmail.com>
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Freescale's flash control driver is using architecture specific timer API
i.e. usec2ticks
Replace usec2ticks with get_timer() (generic timer API)
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add ID for this Numonix / STMicro chip.
Tested on Marvell DB-78460-BP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.
Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support for M25PE16 and M25PX16
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>