On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
distro_bootcmd uses this construct a few times to test $fdt_addr_r,
and fall back on $fdtcontroladdr if not set/invalid:
if fdt addr ${fdt_addr_r}; then
...
else
...
fi
If the `fdt addr` test fails, it prints the following message on the
console, suggesting there is an error when there is not:
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
To remove this potentially confusing error message, this patch adds -q
as a 'quiet' option for fdt addr, and uses this flag in
config_distro_bootcmd.h
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Allow to disable PHY driver in SPL because it checks the CONFIG_SPL_PHY
variable for SPL builds.
The same change was done for usb by commit fd09c205fc ("usb:
s/CONFIG_DM_USB/CONFIG_IS_ENABLED(DM_USB)/").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
File fs/ubifs/crc16.h is standard linux's crc16.h include file. So move it
from fs/ubifs to include/linux where are also other linux include files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot CRC-16 implementation uses polynomial x^16 + x^12 + x^5 + 1 which is
not standard CRC-16 algorithm, but it is known as CRC-16-CCITT. Rename file
crc16.c to crc16-ccitt.c to reduce confusion.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_MMCROOT is only used to set mmcroot, no need a dedicated macro.
Script as below
"
for i in `ls include/configs/*.h`
do
mmcroot=`sed -n '/define.*MMCROOT/ p' $i | awk -F\" '{ print $2;}'`
if [ ! -n "$mmcroot" ]; then
continue
fi
sed -i '/define.*MMCROOT/ d' $i
sed -i 's,\" CONFIG_MMCROOT \",'$mmcroot',g' $i
done
"
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This GPIO is actually an input "Q7_3V3_PCIE_WAKE#_IN" not an output, so
remove the misleaading and incorrect definition.
Cc: Tim Harvey <tharvey@gateworks.com> (re: pci: imx: use vpcie-supply if defined by device-tree)
Signed-off-by: Ian Ray <ian.ray@ge.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop legacy nfsboot script in favor of distroboot DHCP boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use the same name of DHCP Distroboot script as in regular eMMC case.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
We should only access console_devices[file][i] once we have checked that i
< cd_count[file]. Otherwise, we will access uninitialized memory at the end
of the loop. console_devices[file][i] should not be NULL, but putting the
assignment in the loop condition allows us to ensure that i is checked
beforehand. This isn't a bug, but it does make valgrind stop complaining.
Fixes: 400797cad3 ("IOMUX: Split out for_each_console_dev() helper macro")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Scull <ascull@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When every member of a linker list is aligned by the compiler, we can no
longer rely on the sizeof of the struct to determine the number of
entries.
For example, if the struct size is 0x90 but every entry is aligned to 0xa0
by the compiler, the linker list entries takes more space in memory and
the calculation of the number of entries is incorrect. For example, we may
see 0x12 entries when there are only 0x11.
This is a real problem. There may be a general solution, although I cannot
currently think of one. So far it only bites with OF_PLATDATA_RT which
creates a pointer to each entry of the 'struct udevice' linker_list. This
does not happen without that option, so it only affects SPL.
Work around it by manually calculating the aligned size of struct udevice,
then using that for the n_ent calculation.
Note: the alignment fix to linker list was here:
0b2fa98aa5 linker_lists: Fix alignment issue
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if devres is enabled in U-Boot proper it is enabled in SPL.
We don't normally want it there, so disable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
In order to update the DT for rk3288
sync the clock dt-binding header.
This is the state as of v5.17 in Linux.
Keep SCLK_MAC_PLL in use for rk3288 clock driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3288
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Change location to be more in line with other SoCs.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3228
sync the clock dt-binding header.
This is the state as of v5.17 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3228
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
