Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-21 02:33:07 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/configs/ls1046aqds_sdcard_ifc_defconfig

106 lines
3.1 KiB
Text
Raw Normal View History

armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_ARM=y
CONFIG_TARGET_LS1046AQDS=y
configs: Migrate CONFIG_SYS_TEXT_BASE On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-03 17:10:38 +00:00
CONFIG_SYS_TEXT_BASE=0x82000000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01 12:19:22 +00:00
CONFIG_SYS_MALLOC_LEN=0x102000
armv8: ls1046ardb: ls1046aqds: Move SPL macros to defconfig Instead of defining Kconfig macros in header file, move them to defconfig files. Signed-off-by: York Sun <york.sun@nxp.com>
2018-06-26 16:41:24 +00:00
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10 19:31:07 +00:00
CONFIG_NR_DRAM_BANKS=2
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-11-30 17:50:32 +00:00
CONFIG_SYS_MEMTEST_START=0x80000000
CONFIG_SYS_MEMTEST_END=0x9fffffff
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 18:38:00 +00:00
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0x300000
Convert CONFIG_SYS_I2C_MXC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-19 03:12:33 +00:00
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_SYS_I2C_MXC_I2C4=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_DM_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 14:17:29 +00:00
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 17:54:25 +00:00
CONFIG_SPL_TEXT_BASE=0x10000000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-27 01:10:37 +00:00
CONFIG_FSL_USE_PCA9547_MUX=y
configs: Re-sync Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-01 15:41:11 +00:00
CONFIG_FSL_LS_PPA=y
mmc: Rename MMC_SUPPORT to MMC Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> [trini: Fixup some incorrect renames] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-08 18:20:09 +00:00
CONFIG_SPL_MMC=y
serial: Rename SERIAL_SUPPORT to SERIAL Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-08 18:20:12 +00:00
CONFIG_SPL_SERIAL=y
Rename DRIVERS_MISC_SUPPORT to DRIVERS_MISC Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-11 03:14:31 +00:00
CONFIG_SPL_DRIVERS_MISC=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 00:27:54 +00:00
CONFIG_SPL=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_AHCI=y
configs: Re-sync with CONFIG_DISTRO_DEFAULTS A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-10 21:54:38 +00:00
CONFIG_DISTRO_DEFAULTS=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
Convert CONFIG_RAMBOOT_PBL et al to Kconfig This converts the following to Kconfig: CONFIG_RAMBOOT_PBL CONFIG_SYS_FSL_PBL_PBI CONFIG_SYS_FSL_PBL_RCW Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-25 03:11:49 +00:00
CONFIG_RAMBOOT_PBL=y
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046aqds/ls1046aqds_pbi.cfg"
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg"
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=10
common: Move CONFIG_BOOTARGS to Kconfig Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 17:22:17 +00:00
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
configs: Re-sync with CONFIG_DISTRO_DEFAULTS A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-10 21:54:38 +00:00
# CONFIG_USE_BOOTCOMMAND is not set
Convert CONFIG_MISC_INIT_R to Kconfig This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-29 18:13:29 +00:00
CONFIG_MISC_INIT_R=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 18:38:00 +00:00
CONFIG_SPL_FSL_PBL=y
armv8: ls1046a: Enable spl_board_init() function CONFIG_SPL_BOARD_INIT is used for SPL boot. It is only enabled for secure boot at this moment. Enable it in defconfig files for SPL build. Signed-off-by: York Sun <york.sun@nxp.com>
2017-05-15 15:52:02 +00:00
CONFIG_SPL_BOARD_INIT=y
spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to Kconfig Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Fix sniper and kc1 migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-16 17:19:05 +00:00
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
armv8: ls1046ardb: ls1046aqds: Move SPL macros to defconfig Instead of defining Kconfig macros in header file, move them to defconfig files. Signed-off-by: York Sun <york.sun@nxp.com>
2018-06-26 16:41:24 +00:00
CONFIG_SPL_ENV_SUPPORT=y
i2c: Rename SPL/TPL_I2C_SUPPORT to I2C Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-11 03:14:36 +00:00
CONFIG_SPL_I2C=y
ppc: Rename MPC8XXX_INIT_DDR_SUPPORT to MPC8XXX_INIT_DDR Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-08 18:20:16 +00:00
CONFIG_SPL_MPC8XXX_INIT_DDR=y
Rename SPL_WATCHDOG_SUPPORT to SPL_WATCHDOG Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-11 03:14:28 +00:00
CONFIG_SPL_WATCHDOG=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_CMD_BOOTZ=y
cmd: Toggle the default value of CONFIG_CMD_IMLS Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-08 18:48:01 +00:00
CONFIG_CMD_IMLS=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_CMD_GREPENV=y
Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig - Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-17 21:59:45 +00:00
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_CMD_MEMINFO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_MEMTEST=y
configs: ls1046aqds: enable CMD_GPIO Enable CMD_GPIO for board ls1046aqds Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-05 11:02:13 +00:00
CONFIG_CMD_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 18:34:30 +00:00
CONFIG_CMD_GPT=y
Convert CONFIG_CMD_PCI to Kconfig This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-04 22:34:34 +00:00
CONFIG_CMD_I2C=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_CMD_MMC=y
configs: Migrate CMD_NAND* Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-29 01:31:42 +00:00
CONFIG_CMD_NAND=y
Convert CONFIG_CMD_PCI to Kconfig This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-04 22:34:34 +00:00
CONFIG_CMD_PCI=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-11 15:20:19 +00:00
CONFIG_CMD_USB=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_CMD_CACHE=y
cmd: Kconfig: Move CONFIG_MP to Kconfig This patch moves CONFIG_MP to Kconfig Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-19 10:24:23 +00:00
CONFIG_MP=y
Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-22 21:55:07 +00:00
CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:4m(nand_uboot),36m(nand_kernel),472m(nand_free);spi0.0:2m(uboot),14m(free)"
disk: convert CONFIG_EFI_PARTITION to Kconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-27 10:00:41 +00:00
# CONFIG_SPL_EFI_PARTITION is not set
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_OF_CONTROL=y
configs: ls1012a/ls1046a: Add CONFIG_ENV_OVERWRITE in defconfig CONFIG_ENV_OVERWRITE disables write protection on various environment variables like "ethaddr" and "serial". Enable this config in LS1046A and LS1012A defconfigs. This resolves an error while setting multiple values of "ethaddr" variable. Before the change: => setenv ethaddr 00:E0:0C:00:06:0 => setenv ethaddr 00:E0:0C:00:06:1 Error: Can't overwrite "ethaddr" Error inserting "ethaddr" variable, errno=1 After the change: => setenv ethaddr 00:E0:0C:00:06:0 => setenv ethaddr 00:E0:0C:00:06:1 Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-30 10:08:07 +00:00
CONFIG_ENV_OVERWRITE=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 11:16:32 +00:00
CONFIG_ENV_IS_IN_MMC=y
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
armv8: ls1046aqds: Add LS1046AQDS board support LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-07 09:56:14 +00:00
CONFIG_DM=y
configs: ls1046a: enable sata configs for all ls1046a defconfigs Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1046ardb and ls1046aqds defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1046a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-30 11:14:47 +00:00
CONFIG_SATA_CEVA=y
Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-01 21:51:58 +00:00
CONFIG_FSL_CAAM=y
nxp: Migrate CONFIG_DDR_CLK_FREQ to Kconfig As this symbol can either be a fixed value or the function get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ to that value and now include/clock_legacy.h contains the function prototype or defines get_board_ddr_clk() to that static value. Update callers to test for DYNAMIC or STATIC. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-21 17:50:17 +00:00
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
nxp: Migrate a number of DDR related symbols to Kconfig - Guard most of the options in drivers/ddr/fsl/Kconfig with SYS_FSL_DDR || SYS_FSL_MMDC. - Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER to Kconfig. - Clean up the logic for including the DDR_ECC_CMD code. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-21 17:50:18 +00:00
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_DM_I2C=y
Convert CONFIG_I2C_SET_DEFAULT_BUS_NUM et al to Kconfig This converts the following to Kconfig: CONFIG_I2C_SET_DEFAULT_BUS_NUM CONFIG_I2C_DEFAULT_BUS_NUMBER Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-19 03:12:37 +00:00
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig - Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-17 21:59:45 +00:00
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
treewide: Migrate CONFIG_FSL_ESDHC to Kconfig Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-03-28 12:38:19 +00:00
CONFIG_FSL_ESDHC=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 22:18:38 +00:00
CONFIG_MTD=y
flash: complete CONFIG_SYS_NO_FLASH move with renaming We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-11 13:43:54 +00:00
CONFIG_MTD_NOR_FLASH=y
Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-14 20:10:50 +00:00
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_SYS_FLASH_CFI=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 22:18:38 +00:00
CONFIG_MTD_RAW_NAND=y
Convert CONFIG_NAND_FSL_ELBC et al to Kconfig This converts the following to Kconfig: CONFIG_NAND_FSL_ELBC CONFIG_NAND_FSL_IFC Note that a number of PowerPC platforms had previously enabled CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer enable the option, reducing the size of a few functions. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-22 18:50:37 +00:00
CONFIG_NAND_FSL_IFC=y
Convert CONFIG_SYS_NAND_ONFI_DETECTION to Kconfig This converts the following to Kconfig: CONFIG_SYS_NAND_ONFI_DETECTION Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-22 18:50:34 +00:00
CONFIG_SYS_NAND_ONFI_DETECTION=y
Convert CONFIG_SF_DEFAULT_* to Kconfig This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-27 14:20:36 +00:00
CONFIG_SF_DEFAULT_BUS=1
Move PHYLIB to Kconfig Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-02 00:19:59 +00:00
CONFIG_PHYLIB=y
Convert CONFIG_PHYLIB et al to Kconfig This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-24 19:35:53 +00:00
CONFIG_PHYLIB_10G=y
CONFIG_PHY_REALTEK=y
CONFIG_PHY_VITESSE=y
cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:00:42 +00:00
CONFIG_E1000=y
configs: Migrate CONFIG_FMAN_ENET and some related options to Kconfig Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-12 11:59:12 +00:00
CONFIG_FMAN_ENET=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-29 14:48:01 +00:00
CONFIG_NVME=y
armv8: ls1046a: Enable PCIe and E1000 in defconfigs The patch enables PCIe and E1000 in ls1046a related defconfigs. Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-12-13 06:54:21 +00:00
CONFIG_PCI=y
CONFIG_DM_PCI_COMPAT=y
pci: layerscape: Add specific config entry for RC and EP mode driver Add Root Complex and Endpoint mode specific config entries, such that it's feasible to enable the RC and/or EP mode driver indepently. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-09 15:31:42 +00:00
CONFIG_PCIE_LAYERSCAPE_RC=y
CONFIG_PCIE_LAYERSCAPE_EP=y
configs: Migrate CONFIG_FMAN_ENET and some related options to Kconfig Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-12 11:59:12 +00:00
CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
configs: ls1046a: enable sata configs for all ls1046a defconfigs Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1046ardb and ls1046aqds defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1046a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-30 11:14:47 +00:00
CONFIG_DM_SCSI=y
cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:00:42 +00:00
CONFIG_SYS_NS16550=y
Convert CONFIG_SPI to Kconfig This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 17:51:26 +00:00
CONFIG_SPI=y
cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:00:42 +00:00
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
armv8: ls1046a: enable usb in defconfig Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-20 09:12:49 +00:00
CONFIG_USB=y
configs: Migrate all of the existing USB symbols, except fastboot This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-25 21:50:26 +00:00
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
Reference in a new issue Copy permalink