u-boot/board/freescale/p1_p2_rdb_pc
Andy Fleming e76cd5d4cf 8xxx: Change all 8*xx_DDR addresses to 8xxx
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.

This patch does:

s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g

All 85xx, 86xx, and 83xx have been built with this change.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-27 17:45:17 -06:00
..
ddr.c powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL boot 2012-11-26 15:41:27 -06:00
law.c powerpc/mpc85xx/p1_p2_rdb_pc: clean up memory map 2012-11-26 15:41:26 -06:00
Makefile powerpc/mpc85xx/p1_p2_rdb_pc: new SPL support 2012-11-26 15:41:25 -06:00
p1_p2_rdb_pc.c powerpc/mpc85xx/p1_p2_rdb_pc: new SPL support 2012-11-26 15:41:25 -06:00
README doc: cleanup - move board READMEs into respective board directories 2012-07-29 15:42:02 +02:00
spl_minimal.c 8xxx: Change all 8*xx_DDR addresses to 8xxx 2012-11-27 17:45:17 -06:00
tlb.c powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL boot 2012-11-26 15:41:27 -06:00

Overview
--------
P1_P2_RDB_PC represents a set of boards including
    P1020MSBG-PC
    P1020RDB-PC
    P1020UTM-PC
    P1021RDB-PC
    P1024RDB
    P1025RDB
    P2020RDB-PC

They have similar design of P1020RDB but have DDR3 instead of DDR2. P2020RDB-PC
has 64-bit DDR. All others have 32-bit DDR.

Key features on these boards include:
    * DDR3
    * NOR flash
    * NAND flash (on RDB's only)
    * SPI flash (on RDB's only)
    * SDHC/MMC card slot
    * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
    * PCIE slot and mini-PCIE slots

As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported with
this approach. ODT option is forced to fit this set of boards, again because
they don't have regular DIMMs.

CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification
for writing timing.

VSC firmware Address is defined by default in config file for eTSEC1.

SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.

Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have
pins multiplexing. QE function needs to be disabled to access Nor Flash and
CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below

'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.