The only UART that is garunteed on Ventana boards is UART2 (serial-console).
Remove UART1 pinmux as that it is not consistent across all Ventana boards
and U-Boot doesn't need it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi
and get rid of the enet reset gpio handling from the board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable all the necessary configs for SPL DM and FIT support for
mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable all the necessary configs for SPL DM and FIT support for
mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit 8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This matches one of the following three boards (or fails):
- imx6q-sabreauto
- imx6qp-sabreauto
- imx6dl-sabreauto
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This matches one of the following three boards (or fails):
- imx6q-sabresd
- imx6qp-sabresd
- imx6dl-sabresd
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add the DM support for USB. For that, DM_REGULATOR is needed.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The secure_boot.txt guide was replaced by mx6_mx7_secure_boot.txt and
mx6_mx7_spl_secure_boot.txt documents.
Both documents covers all steps needed for SPL and non-SPL tagets,
so remove secure_boot.txt file to avoid duplicated content.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
All guides are currently located at doc/imx/habv4/guides/ directory.
Move encrypted_boot.txt document to guides directory.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The current U-Boot implementation includes SPL targets for
some NXP development boards:
- mx6sabreauto_defconfig
- mx6sabresd_defconfig
- mx6ul_14x14_evk_defconfig
- mx6ul_9x9_evk_defconfig
Add additional steps needed to completly secure the
bootloader image.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add HABv4 documentation for non-SPL targets covering the
following topics:
- How to sign an securely boot an u-boot-dtb.imx image.
- How to extend the root of trust for additional boot images.
- Add 3 CSF examples.
- Add IVT generation script example.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The HABv4 is supported in i.MX50, i.MX53, i.MX6, i.MX7,
series and i.MX 8M, i.MX8MM devices.
Add an introductory document containing the following topics:
- HABv4 Introduction
- HABv4 Secure Boot
- HABv4 Encrypted Boot
- HAB PKI tree generation
- HAB Fast Authentication PKI tree generation
- SRK Table and SRK Hash generation
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
There is no need to have an extra hab directory under doc/imx/.
Habv4 and AHAB documentation can be added directly in doc/imx/ for a
cleaner documentation structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbca ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
Signed-off-by: Adam Ford <aford173@gmail.com>
mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJcY9m6AAoJECszeR4D/txgTikP/3J6vXriBjXh13AtsGQpCeaC
9HCRHV/iR4MNki1EaexoGkF5Mnb6ARufuG4ru+6X9lrrQWbgIyzr0NWH6ZQEz31u
MENZG5iO9fo5IZJrfc/pkBk0++dB/N/3/h0PgN6/Y3rVkUVXbkYieX7D8J62T4kn
mkpZJTRqOZD16RAk4tENOOpVclrU8HkUccg8+MgxSN0TqX18oxF4Wgbgn2GGoU8R
ANF/6Ke6mOAxUedA58Y9KflZ02q0bThoMtBYeWxI+WYCsGVgH9a4Q/TVwhZMbjH0
dAj3aAIRf6TmAOcQAlHhT8muruYlO6ri8ztq/PB/3ThDvagc4dnrXNxDFWlo6Y4q
WPJBw9TAGDpnpDplx4WW6CJdP9HlXH/NIFWEYokqyeLcnjcvvH34zfrgWTcD8epJ
gtDzLO2YsblA+q5SsbzAk/BsNjLpkzA1St7S/vZFCVNbazBAZgGUD2NoChI3MfM7
n0KQr5rlvrdckYRhln6IEZBXvs0drsb9Ki4g7jw1N9PDMmUW8uwArGINT2Zi2HW0
lPkf+jlw30ds2zcHoUH0EA8cfYgdTzvCLIKjmodN4nd/taKN292NbTmaQeZQ9wqG
TclMiyY9VoqIeKV4l44q9lxdowS82cb0G203eHyTIOAFJlNtuthNdISJIFIrqljA
na3RDAFYC8Ibfo+zIgLb
=g6l7
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2019-02-13
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
We check the existence of files with fs_exist(). This function calls
fs_close(). If we do not set the active block device again fs_opendir()
fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the
`cd` command in the EFI shell fails.
So let's add the missing set_blk_dev(fh) call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We have to ensure while printing UTF16 strings that we do not exceed the
end of the print buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich ran into issues with HII and iPXE which lead to #SErrors on
his Odroid-C2 system. We definitely do not want to regress just yet,
so let's not expose the HII protocols by default.
Instead, let's make it a config option that people can play with
This way, we can stabilize the code in tree without breaking any
users.
Once someone figures out, why this breaks iPXE (probably a NULL
dereference), we can enable it by default.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
---
v1 -> v2:
- Remove HII selftest as well
v2 -> v3:
- Make config option
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
For correct indention use EFI_PRINT() instead of debug().
For printing efi_uintn_t or size_t use the %zu or %zx format code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_st_printf() does not support format code %ld. Anyway the format code
for size_t would be %zu which isn't supported either.
We do not want any divisions to avoid invalid references to integer
arithmetic routines, cf.
https://gcc.gnu.org/onlinedocs/gccint/Integer-library-routines.html.
As a simple remedy remove the noisy messages from the output.
They are not relevant for automated testing.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This efi_selftest tests HII database protocol and HII string protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch is a place holder for HII configuration routing protocol and
HII configuration access protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling keyboard layout package in HII database protocol.
A package can be added or deleted in HII database protocol, but
we don't set 'current' keyboard layout as there is no driver that
requests a keyboard layout.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling GUID package in HII database protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides enough implementation of the following protocols to
run EDKII's Shell.efi and UEFI SCT:
* EfiHiiDatabaseProtocol
* EfiHiiStringProtocol
Not implemented are:
* ExportPackageLists()
* RegisterPackageNotify()/UnregisterPackageNotify()
* SetKeyboardLayout() (i.e. *current* keyboard layout)
HII database protocol in this patch series can handle only:
* GUID package
* string package
* keyboard layout package
(The other packages, except Device path package, will be necessary
for interactive and graphical UI.)
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
