The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h
(but some boards still have redundant definitions).
This commit moves the definition and the document in README to
Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000,
the sanity check in lib/time.c should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add ddr3 commands:
test <start_addr in hex> <end_addr in hex> - test DDR from start\n
address to end address\n
ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n
compare DDR data of (size) bytes from start address to end
address\n
ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n
in DDR data at <addr>, the command will read a 32-bit data\n
from <addr>, and write (data ^ bit_err) back to <addr>\n
Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used
for ddr3 commands and for now it's not needed any more.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The phy framework has function to get link, so use it
instead of own implementation.
There is no reason to check SGMII link while sending each
packet, phy link is enough. Check SGMII link only while
ethernet open.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently keystone has misc_init_r where all DSPS are turned off
by default. So enable this function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
The Marvell MV78460 eval board DB-78460-BP seems to need a longer
PHY autonegotiation timeout than the "standard" 4 seconds. So lets
make this timeout configurable. If not defined in the board config
header the original 4000ms is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
These mbus functions are ported from Barebox. The Barebox version is
ported from Linux. These functions will be first used by the upcoming
Armada XP support. Later other Marvell SoC's will be adopted to use
these functions as well (Kirkwood, Orion).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Enable FIT support and the bootelf command. Also change the default load
address to somewhere other than the normal load address of the kernel,
to allow for decompression without overwriting the original file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To get a display in U-Boot on link you must either build a coreboot that
always sets it up, or use Esc-Refresh-Power to reset the machine.
When we do have a display, it is nice to display the model at the top, so
enable this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
We may as well use hush. The auto-complete option was incorrect so this was
not enabled. Also expand the command line size a little and go back to the
default prompt since "boot>" doesn't seem any more useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
The fdt_for_each_subnode() iterator macro provided by this patch can be
used to iterate over a device tree node's subnodes. At each iteration a
loop variable will be set to the next subnode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fdtdec_pci_get_bdf() function returns the bus, device, function
triplet of a PCI device by parsing the "reg" property according to the
PCI device tree binding.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the fdt_get_resource() and fdt_get_named_resource() functions which
can be used to parse resources (memory regions) from an FDT. A helper to
compute the size of a region is also provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node, a property name and an index, the new function
fdt_get_string_index() will return in an output argument a pointer to
the index'th string in the property's value.
The fdt_get_string() is a shortcut for the above with the index being 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node and a property name, the new fdt_find_string()
function will look up a given string in the string list contained in the
property's value and return its index.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node and a property name, the fdt_count_strings()
function counts the number of strings found in the property value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB support must be enabled before config_distro_bootcmd.h is included
for bootcmd to include USB-related functionality.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Enable DWC2 USB, storage and ethernet support. Tested on RPi B+.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.
This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.
Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Vince Bridgers <vbridger@altera.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Adjust the driver so that leaf functions take a pointer to the serial port
register base. Put all the global configuration in the init function, and
use the same settings from then on.
This makes it much easier to move to driver model without duplicating the
code, since with driver model we use platform data rather than global
settings.
The driver is compiled with either the CONFIG_PL010_SERIAL or
CONFIG_PL011_SERIAL option and this determines the uart type. With driver
model this needs to come in from platform data, so create a new
CONFIG_PL01X_SERIAL config which brings in the driver, and adjust the
driver to support both peripheral variants.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add driver model support with this driver. Boards which use this driver
should define platform data in their board files.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U_BOOT_DEVICE macro allows the declaration of a single U-Boot device.
Add an equivalent macro to declare an array of devices, for convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing ll_entry_declare() permits a single element of the list to
be added to a linker list. Sometimes we want to add several objects at
once. To avoid lots of messy declarations, add a macro to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this driver to use driver model and move smdk5420 boards over to
use it.
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox cros_ec emulation driver to work with driver model, and
switch over to driver model for sandbox cros_ec.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for driver model if enabled. This involves minimal changes
to the code, mostly just plumbing around the edges.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Use driver model for exynos5 board SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.
CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This feature provides for init of a single SPI port for the soft SPI
feature. It is not really compatible with driver model since it assumes a
single SPI port. Also, inserting SPI init into the driver by means of
a #define is not very nice.
This feature is not used by any active boards, so let's remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust the sandbox SPI driver to support driver model and move sandbox over
to driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
U-Boot includes a SPI emulation driver already but it is not explicit, and
is hidden in the SPI flash code.
Conceptually with sandbox's SPI implementation we have a layer which
creates SPI bus transitions and a layer which interprets them, currently
only for SPI flash. The latter is actually an emulation, and it should be
possible to add more than one emulation - not just SPI flash.
Add a SPI emulation uclass so that other emulations can be plugged in to
support different types of emulated devices on difference buses/chip
selects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a uclass which provides access to SPI buses and includes operations
required by SPI.
For a time driver model will need to co-exist with the legacy SPI interface
so some parts of the header file are changed depending on which is in use.
The exports are adjusted also since some functions are not available with
driver model.
Boards must define CONFIG_DM_SPI to use driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
(Discussed some follow-up comments which will address in future add-ons)
The sequence number is unique within the uclass, so state this clearly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses sometimes want to pass data to their children when they are probed.
For example, a SPI bus may want to tell the slave device about the chip
select it is connected to.
Add a new function to permit the parent data to be supplied to the child.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses need to iterate through their children in some situations. Add a few
functions to make this easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for s5p_goni.
Signed-off-by: Simon Glass <sjg@chromium.org>
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for smdkc100.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add proper initialization of GPIO pins used by software i2c.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The driver model supports two ways for passing device parameters;
Device Tree and platform_data (board file).
Each driver should generally support both of them because some
popular IPs are used on various platforms.
Assume the following scenario:
- The driver Foo is used on SoC Bar and SoC Baz
- The SoC Bar uses Device Tree control (CONFIG_OF_CONTROL=y)
- The SoC Baz does not support Device Tree; uses a board file
In this situation, the device driver Foo should work with/without
the device tree control. The driver should have .of_match and
.ofdata_to_platdata members for SoC Bar, while they are meaningless
for SoC Baz; therefore those device-tree control code should go
inside #ifdef CONFIG_OF_CONTROL.
The driver code will be like this:
#ifdef CONFIG_OF_CONTROL
static const struct udevice_id foo_of_match = {
{ .compatible = "foo_driver" },
{},
}
static int foo_ofdata_to_platdata(struct udevice *dev)
{
...
}
#endif
U_BOOT_DRIVER(foo_driver) = {
...
.of_match = of_match_ptr(foo_of_match),
.ofdata_to_platdata = of_match_ptr(foo_ofdata_to_platdata),
...
}
This idea has been borrowed from Linux.
(In Linux, this macro is defined in include/linux/of.h)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The header files include/dm/platdata.h and include/dm/uclass.h
use ll_entry_declare(); therefore they depend on
include/linker_lists.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The header file include/linker_lists.h uses __aligned();
therefore it depends on include/linux/compiler.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The struct udevice stands for a device, not a driver.
The driver_info.name is a driver's name, which is referenced
to bind devices.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update Apalis T30 as per the following commits
c369139234
tegra: dts: Add serial port details
461be2f96e
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clean-up a spurious new line which got introduced resp. left behind by
commit
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Wondering what exactly that one should bring (;-p). Looks like a remnant of the last commit
783e6a72b8
kconfig: move CONFIG_OF_* to Kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use architecture specific memcpy to speed up things.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a new setup@ section to the FIT which can be used to provide a setup
binary for booting Linux on x86. This makes it possible to boot x86 from
a FIT.
Signed-off-by: Simon Glass <sjg@chromium.org>
HDMI config options can be placed into the common mx6sabre_common.h file to
avoid duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable blob commands for platforms having SEC 4.0 or greater
for secure boot scenarios
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's SEC block has built-in Blob Protocol which provides
a method for protecting user-defined data across system power
cycles. SEC block protects data in a data structure called a Blob,
which provides both confidentiality and integrity protection.
Encapsulating data as a blob
Each time that the Blob Protocol is used to protect data, a
different randomly generated key is used to encrypt the data.
This random key is itself encrypted using a key which is derived
from SoC's non volatile secret key and a 16 bit Key identifier.
The resulting encrypted key along with encrypted data is called a blob.
The non volatile secure key is available for use only during secure boot.
During decapsulation, the reverse process is performed to get back
the original data.
Commands added
--------------
blob enc - encapsulating data as a cryptgraphic blob
blob dec - decapsulating cryptgraphic blob to get the data
Commands Syntax
---------------
blob enc src dst len km
Encapsulate and create blob of data $len bytes long
at address $src and store the result at address $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
blob dec src dst len km
Decapsulate the blob of data at address $src and
store result of $len byte at addr $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable CAAM in platforms supporting the hardware block.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.
So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot binary size has been increased from 512KB to 768KB.
So update CONFIG_RESET_VECTOR_ADDRESS to reflect the same for
P1010 SPI Flash Secure boot target.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Modified subject to P1010RDB]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a block to avoid a build error with the variable declaration.
Enable the option on sandbox to prevent an error being introduced in
future.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Commit 832472 "tools: socfpga: Add socfpga preloader signing
to mkimage" added tools/socfpga.c which relies on htole32,
le32toh and friends. While compiler.h includes these protypes
for linux from endian.h, it doesn't do so for FreeBSD. Hence
include <sys/endian.h> for FreeBSD.
Cc: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:
Copyright 1994 - 2000 Neil Russell.
(See License)
I analyzed the source code of LiMon v1.4.2 which was used for this
import. It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991. So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2. Mark them as such.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Commit 12cc543767 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
SCIF of koelsch use external clock mode.
This enables external clock mode on koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SCIF of lager use external clock mode.
This enables external clock mode on lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The clock of SCIF (serial port) of lager is supplied from External
Clock. And value of clock is 14.7456MHz.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Enable this feature to support driver model before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the arndale features are common with other exynos5250 boards. To
permit easier addition of driver model support, use the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards do not in fact have a Chrome OS EC, nor a TPS565090 PMIC, so
move the settings into a separate common file to be used by those that need
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A few things are common but are not in the common file. Fix this and
rename the file to fit with the other exynos*-common files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since exynos4 and exyno5 share many settings, we should move these into
a common file to avoid duplication.
In effect the changes are that all exynos boards now have EXT4 and FAT
write support. This affects exynos5250 and exynos5420 which previously
did not. This also disables the ext2 commands which are equivalent to
ext4 anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We want exynos5250-dt.h to be a board which can support any exynos5250
device. This matches the naming used by Linux. As a first step, rename
the existing -dt files to -common to make it clear they are common files,
and not specific boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With the driver model conversion we are going to be using driver model for
SPI and not for I2C. This works OK so long as a board doesn't need both
dm and non-dm versions of the cros_ec driver. Since pit uses SPI and snow
uses I2C we need to split the configs so that only one driver is compiled
for each platform.
We can fix this later when driver model supports I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards
cannot due to a hardware design decision. Select the correct driver to use
in each case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Things run faster when the data cache is enabled, so turn it on along with
the 'dcache' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Support reading/writing ext4 partitions.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable 'fastboot' command.
This is currently enabled but not yet functional. Including it in the
configuration will ease further testing and development as discussed
on the mailing list.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Some users (QNX and Windows CE users in particular) have asked
to disable the Penguin shown on the display at boot time.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Increase the maximum number of arguments allowed by the Hush parser.
This prevents errors when users or scripts aren't quoting parameters
when setting the "bootargs" variable et al.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable the "i2c edid" command to query data from an attached
HDMI monitor.
Usage is typically this:
U-Boot > i2c dev 1
U-Boot > i2c edid 0x50
...
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
If no boot script was found, expose internal storage over the
USB mass storage gadget to allow easy programming.
This is especially useful when SD cards are inaccessible or when
loading SATA drives.
More details are available in this blog post:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Remove the individual attempts to load using ext2 and fat, replace with the
generic load command supporting available filesystem types.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
This patch enables boot to USB storage devices by expanding on the list
of boot devices.
Because the USB startup currently takes a long time, it places USB at
the end of the list of supported devices.
You can over-ride the boot order using the bootdevs environment variable.
For instance, this will make USB the first (highest priority) device:
U-Boot > setenv bootdevs usb mmc sata
U-Boot > saveenv
Signed-off-by: Diego Rondini <diego.rondini@kynetics.it>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for the USB mass storage to enable access to on-board
storage (especially eMMC and SATA).
Details at:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable and use the CONFIG_CMD_FS_GENERIC to avoid hard-coding the
filesystem type into the environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Split the SoCFPGA configuration into SoC-specific part which is
common for all boards (socfpga_cyclone5_common.h) and a board
specific part. There is currently only one board, which is the
generic SoCFPGA board (socfpga_cyclone5.h), but there are more
to come.
This is necessary due to various features of the boards, which
unfortunatelly cannot be autodetected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reorganize and cleanup the configuration file for SoCFPGA. There
is no functional change after this cleanup. This was necessary,
since the file was a wild mess and it was impossible to make sense
of it's content, let alone change something without breaking some
other thing. This patch puts the contents on par with regular U-Boot
standards.
Also remove unused preprocessor symbols CONFIG_SINGLE_BOOTOADER
and CONFIG_USE_IRQ, which is undefined by default. Finally, do
logical reordering of the defines in the file so it's much more
readable. The reordering was also necessary for the splitting
as the initial one was messy.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Enable the SDMMC boot as default boot for SOCFPGA U-Boot dev kit.
Enable the bootz command as zImage is used instead uImage.
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable the DesignWare MMC controller driver support
for SOCFPGA Cyclone5 dev kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable the PL310 L2 cache controller support for the SoCFPGA.
With the cache related issues resolved, this is safe to be done.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The code is now fixed to the point where we can safely enable
the L1 data cache. Enable the D-Cache and set it as write-alloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The Cortex-A9 has 32-byte long L1 cachelines. Define this value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
The timer reload value is a property of the timer hardware and there
is no reason for this to be configurable. Place this into the timer
driver just like on the other hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Add the entire bulk of code to read out clock configuration from the SoCFPGA
CPU registers. This is important for MMC, QSPI and UART drivers as otherwise
they cannot determine the frequency of their upstream clock.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Fixed the L4 MP clock divider and synced the clock code with latest
rocketboards codebase (thanks Dinh for pointing this out)
Like many platforms, the Altera socfpga platform requires that the
preloader be "signed" in a certain way or the built-in boot ROM will
not boot the code.
This change automatically creates an appropriately signed preloader
from an SPL image.
The signed image includes a CRC which must, of course, be generated
with a CRC generator that the SoCFPGA boot ROM agrees with otherwise
the boot ROM will reject the image.
Unfortunately the CRC used in this boot ROM is not the same as the
Adler CRC in lib/crc32.c. Indeed the Adler code is not technically a
CRC but is more correctly described as a checksum.
Thus, the appropriate CRC generator is added to lib/ as crc32_alt.c.
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
V2: - Zap unused constant
- Explicitly print an error message in case of error
- Rework the hdr_checksum() function to take the *header directly
instead of a plan buffer pointer
Remove this symbol from configs, since it's unused.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
The DMA descriptors used by the DW MMC block must be aligned to cacheline
size, otherwise we are unable to properly flush/inval cache over them and
we get data corruption.
The reason I chose this approach of expanding the structure is because
the driver allocates the descriptors in bulk. This approach does waste
space by inserting slop inbetween the descriptors, but it makes access
to the descriptors easy as the compiler does know the real size of the
structure. It also makes cache operations easy, since the size of the
structure is cache aligned and the structure start address is as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pavel Machek <pavel@denx.de>
Get rid of the line-over-80 problems and zap the typedef that
went alongside those enums.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
This patch adds support for the OT1200 series of devices.
Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio
For more details see README.
Changes v1 > v2
- make use of enable_cspi_clock(..)
- fix usage of OUTPUT_40OHM define
- added README
Changes v2 > v3
- improve spelling in README
- added own copy of mx6q_4x_mt41j128.cfg
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
PERST_GPIO and POWER_GPIO are currently swapped.
Fix the GPIO assignments as per the board schematics.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Besides converting the LS-XHL and LS-CHLv2 to generic board, fix a typo
which accidentally reverted the bootsource to 'hdd' although the default
bootsource should be 'legacy'.
Cc: Tom Rini <trini@ti.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Siemens boards are now using DFU in fullspeed only. For
this CONFIG_USB_GADGET_DUALSPEED is undefined.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Liu Bin <b-liu@ti.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Use the new force parameter to make the stdio_deregister succeed, replacing
stdin with a nulldev, and assume that the usb keyboard will come back after
the reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In some cases we really want to move forward with a deregister, add a force
parameter to allow this, and replace the dev with a nulldev in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch add MTDIDS and MTDPARTS defaults settings to sheevaplug
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Changes in v1:
- add MTDIDS and MTDPARTS default to sheevaplug
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch move the environment offset in sheevaplug.
The size of the u-boot binary is become too big.
Fix saving environments was result of corrupting the u-boot.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Changes in v2:
- patch description
Changes in v1:
- fix sheevaplug environment offset
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Enable the CONFIG_CMD_FS_GENERIC on m53evk to avoid per-fs specific commands
and tweak the environment to cater for this new option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable the CONFIG_CMD_FS_GENERIC on m28evk to avoid per-fs specific commands
and tweak the environment to cater for this new option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make sure the boot.scr exists on the card before loading it
from the card to avoid annoying message on the console.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make sure the boot.scr exists on the card before loading it
from the card to avoid annoying message on the console.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
1. Set the image load partition to the first FAT partition.
2. Set the kernel rootfs partition to the second partition.
Signed-off-by: Ye.Li <B37916@freescale.com>
To support loading FDT file for kernel, add the fdt address,
file and loading script to arm2 board default environment.
Signed-off-by: Ye.Li <B37916@freescale.com>
Some of the #defines in spi.h are not bracketed. To avoid future mistakes
add brackets. Also add an explanatory comment for SPI_CONN_DUAL_...
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Sandbox may as well support everything. This increases the amount of code
that is built/tested by sandbox, and also provides access to all the
supported SPI flash devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
of_bus_default_count_cells can be used to get the #address-cells
and #size-cells defined by the current node's parent node. This
is required when using of_read_number to read from FDT nodes that
can be 32 or 64 bytes depending on values defined by the parent.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
This is being done so that it can be used outside 'fdt_support.c'. Making
life more convenient when reading device node properties that can be 32
or 64 bits long.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.
Signed-off-by: York Sun <yorksun@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of NOR and NAND flash for simulator target.
Here
IFC - CS0: NOR flash
IFC - CS1: NAND flash
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This option specifies the default Device Tree used for the run-time
configuration of U-Boot.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <michal.simek@xilinx.com>
This commit moves:
CONFIG_OF_CONTROL
CONFIG_OF_SEPARATE
CONFIG_OF_EMBED
CONFIG_OF_HOSTFILE
Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.
Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The libc headers on FreeBSD and likely related projects as well contain an
header file, cdefs.h which provides similiar functionality as linux/compiler.h.
It provides compiler independent defines like __weak __packed, to allow
compiling with multiple compilers which might have a different syntax for such
extension.
Since that header file is included in multiple standard headers, like stddef.h
and stdarg.h, multiple definitions of those defines will be present if both are
included. When compiling u-boot the compiler will warn about it hundreds of
times since e.g. common.h will include both files indirectly.
commit 7ea50d5284 "compiler_gcc: do not redefine
__gnu_attributes" prevented such redefinitions, but this was undone by commit
fb8ffd7cfc "compiler*.h: sync
include/linux/compiler*.h with Linux 3.16".
Add the checks back where necessary to prevent such warnings.
As the original patch this checkpatch warning is ignored:
"WARNING: Adding new packed members is to be done with care"
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since clang has a different definition for uninitialized_var
it will complain that it is redefined in include/compiler.h.
Since these are already defined in linux/compiler.h just remove
this instance.
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The section name and the C variable name seem to be opposite.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Now config_cmd_defaults.h is empty so it can be deleted safely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_IMPORTENV is defined in config_cmd_defaults.h,
it should be enabled for all the boards except bf506f-ezkit
that undefs it explicitely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_GO is defined in config_cmd_defaults.h
(and no board undefs it its own header), it can be moved to
Kconfig with the default value "y".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_EXPORTENV is defined in config_cmd_defaults.h,
it should be enabled for all the boards except bf506f-ezkit
that undefs it explicitely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_CRC32 is defined in config_cmd_defaults.h,
it is enabled for all the boards except the ones undefining it
explicitly:
kwb
tseries_mmc
tseries_nand
tseries_spi
vct_platinum_onenand_small
vct_platinum_small
vct_platinumavc_onenand_small
vct_platinumavc_small
vct_premium_onenand_small
vct_premium_small
The default value of this config option should be "y" and
"# CONFIG_CMD_CRC32 is not set" should be added for those exceptions.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_CMD_BOOTM is defined in config_cmd_defaults.h
which is forcebly included from each board.
So, the default value of "config CMD_BOOTM" should be "y".
For some boards undefining it (bf506f-ezkit, controlcenterd_TRAILBLA,
controlcenterd_TRAILBLAZER_DEVELOP, controlcenterd_TRAILBLAZER),
"# CONFIG_CMD_BOOTM is not set" should be added to their defconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
If this option is enabled, the objects under lib/ directory
are compiled with speed optimization, not size optimization.
(Currently, only used by some Blackfin boards.)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Scsi disks need to be probed before we try to access them, otherwise all
accesses fail with: ** Bad device size - scsi 0 **.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Karsten Merker <merker@debian.org>
One of the I2C EEPROM is used to store/save and edit mac
addresses of ports.
this patch add required CONFIG to support the same
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
CPC1 is not being enabled by default as powerpc is supposed to
use only CPC2. Though by editing hwconfig en_cpc option,
CPC1 can also be enabled.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB is a Freescale reference board that hosts the T1042 SoC
(and variants). The board is similar to T1040RDB, T1042 is a reduced
personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
T1042RDB is configured with serdes protocol 0x86 which can support
following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
DTSEC1, DTSEC2 are not connected on board.
This Patch
- add T1042RDB support
- updates README file for T1042RDB details and update commands for switching
to alternate banks from vBank0 to vBank4 and vice versa
This patch also does minor clean ups for fdt defines for T1042RDB and
T1042RDB_PI board
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable the Extend address to support SPI flash more than 16MB.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.
Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board support is not in place.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Sabrelite board has two solts: 0 is SD3 (bottom) slot and 1 is uSD4 (top) slot.
This patch makes use of both slots instead of only one.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board not being supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We should not hardcode CONFIG_NETMASK in the config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript' and 'loadbootenv' as already done for 'loadimage' and 'loaduimage' for OMAP4 boards.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Copy them from Linux v3.16 tag.
My main motivation of this commit is to add compiler-clang.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
U-Boot has imported various source files from other projects,
mostly Linux.
Something like
#ifdef __UBOOT__
[ modification for U-Boot ]
#else
[ original code ]
#endif
is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.
Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>