Provide an option to write filesystem independend commands.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the SPI driver support for ZynqMP
The controller is same as zynq SPI controller
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Enable the i2c driver for ZynqMP
Also enable the eeprom for read and writes
to eeprom on ZynqMP
ZynqMP uses the same i2c controller as in Zynq
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for loading sw for R5 with enabling for zynqmp.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
The PicoZed is a System-on-Module board which is marketed as part of
the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000
processor.
This patch adds support that covers all the variants of the PicoZed
including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This
patch set however only covers support for the System-on-Module and does
not cover any extra components that are available on carrier boards
(except those that are fanned out of the module itself).
More information on this board, its variants and available carrier
boards is available at: http://zedboard.org/product/picozed
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Instead of hardcoding the 'fdtfile' variable, let's detect the SoC and
board variant on the fly and change the dtb name.
Based on the scheme done on am335x board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
README file suggests to use 'fdtfile' for the dtb file name and
'fdt_addr_r' for the dtb address in RAM, so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds initial support for Colibri VF50/VF61 based on Freescale
Vybrid SoC.
- CPU clocked at 396/500 MHz
- DDR3 at 396MHz
- for VF50, use PLL2 as memory clock (synchronous mode)
- for VF61, use PLL1 as memory clock (asynchronous mode)
- Console on UART0 (Colibri UART_A)
- Ethernet on FEC1
- PLL5 based RMII clocking (E.g. No external crystal)
- UART_A and UART_C I/O muxing
- Boot from NAND by default
Tested on Colibri VF50/VF61 booting using serial loader over UART.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.
All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Implemented fb_set_reboot_flag() for OMAP5 to set
an environment variable 'dofastboot' when reboot-bootloader called.
This environment variable will be checked in boot command and fastboot
will be called if the variable is set.
If the bootcmd env variable of OMAP5 common is overwritten with board-specific
command, then these changes will not apply.
This was originally intended for DRA7 platform, but now applies to all OMAP5.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=19da2e436e9806259cf1f4988b9e046ab256bf2c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv()
in that case]
Signed-off-by: Tom Rini <trini@konsulko.com>
1. The bits 11..10 for mfp driver strength is only valid for
aspen and old xscale family, for newer Marvell chip, this range
has been moved to 12..11.
2. add sleep bit support
Signed-off-by: Xiang Wang <wangx@marvell.com>
[robh: rebase to current mainline]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Howard <phoward@gme.net.au>
[trini: Add config file, update for ..._ether_addr() -> ..._ethaddr() rename]
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS2085ARDB is a evaluation platform that supports LS2085A
family SoCs. This patch add sbasic support for the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Wire rate IO Processor (WRIOP) provide support of receive and transmit
ethernet frames from the ethernet MAC. Here Each WRIOP block supports
upto 64 DPMACs.
Create a house keeping data structure to support upto 16 DPMACs and
store external phy related information.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Changed MC firmware loading to comply with the new MC boot architecture.
Flush D-cache hierarchy after loading MC images. Add environment
variables "mcboottimeout" for MC boot timeout in milliseconds,
"mcmemsize" for MC DRAM block size. Check MC boot status before calling
flib functions.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of SerDes framework for Layerscape Architecture.
- Add support of 2 SerDes block
- Add SerDes protocol parsing and detection
- Create table of SerDes protocol supported by LS2085A
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.
Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.
Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.
Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.
Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
There is little reason to split these two functions. Bring them together
which simplifies the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
The printf() in panic() adds about 1.5KB of code size to SPL when compiled
with Thumb-2. Provide a smaller version that does not support printf()-style
arguments and use it in two commonly compiled places.
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_DM_DEVICE_REMOVE option takes out code related to removing
devices. It should also remove the 'unbind' code since if we cannot
remove we probably don't need to unbind.
Signed-off-by: Simon Glass <sjg@chromium.org>
In many cases SPL only uses a single serial port and there is no need for
alias sequence support. We will just use the serial port pointed to by
stdout-path in the /chosen node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch extends the U-Boot "led" command to support automatic blinking
by setting a blink frequency in milliseconds. Additionally the number of
supported LEDs is increased to 6 (0...5).
This will be used by the PCA9551 LED driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Switch to CONFIG_ARCH_INTEGRATOR defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Commit d8bafe1310
"ARMv8: enable DM in vexpress64 board" only enabled DM
for the simulated vexpress64 board (FVP) with the
hardcoded clock value for the simulated board, causing
a console regression on the Juno board which was using
a different clock setting.
Fix this by enabling DM for all vexpress64 boards,
defining the clock frequency per-board, deleting the
static array of PL01x ports from the config file and
relying solely on the port defined in the boardfile
using platform data.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NAND-version has been become a bit orphan.
Now we need to reactivate it, so bring necessary things:
- loading devicetree
- switch control signal to correct pins
- setup pinmux
- default-environment
up to date.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
searches the required device for the exactly given name.
This patch, presice this fact for both function's comments.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Uclass API provides a few functions for get/find the device.
To provide a complete function set of uclass-internal functions,
for use by the drivers, the function uclass_get_device_tail()
should be non-static.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model device's API by function:
- dev_get_uclass_name()
And this function returns the device's uclass driver name if:
- given dev pointer, is non_NULL
otherwise, the NULL pointer is returned.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model device's API by function:
- dev_get_driver_ops()
And this function returns the device's driver's operations if given:
- dev pointer, is non-NULL
- dev->driver->ops pointer, is non-NULL
in other case the, the NULL pointer is returned.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model uclass's API by function:
- uclass_get_device_by_name()
And this function returns the device if:
- uclass with given ID, exists,
- device with exactly given name(dev->name), exists,
- device probe, doesn't return an error.
The returned device is activated and ready to use.
Note:
This function returns the first device, which name is equal
to the given one. This means, that using this function you must
assume, that the device name is unique in the given uclass's ID
device list.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model uclass's API by function:
- uclass_find_device_by_name()
And this function returns the device if:
- uclass with given ID, exists,
- device with exactly given name(dev->name), exists.
The returned device is not activated - need to be probed before use.
Note:
This function returns the first device, which name is equal
to the given one. This means, that using this function you must
assume, that the device name is unique in the given uclass's ID
device list.
uclass-internal.h: cleanup - move the uclass_find_device_by_seq()
declaration and description, near the other uclass_find*() functions.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This test introduces new test structure type:dm_test_perdev_uc_pdata.
The structure consists of three int values only. For the test purposes,
three pattern values are defined by enum, starting with TEST_UC_PDATA_INTVAL1.
This commit adds two test cases for uclass platform data:
- Test: dm_test_autobind_uclass_pdata_alloc - this tests if:
* uclass driver sets: .per_device_platdata_auto_alloc_size field
* the devices's: dev->uclass_platdata is non-NULL
- Test: dm_test_autobind_uclass_pdata_valid - this tests:
* if the devices's: dev->uclass_platdata is non-NULL
* the structure of type 'dm_test_perdev_uc_pdata' allocated at address
pointed by dev->uclass_platdata. Each structure field, should be equal
to proper pattern data, starting from .intval1 == TEST_UC_PDATA_INTVAL1.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds 'uclass_platdata' field to 'struct udevice', which
can be automatically allocated at bind. The allocation size is defined
in 'struct uclass_driver' as 'per_device_platdata_auto_alloc_size'.
New device's flag is added: DM_FLAG_ALLOC_UCLASS_PDATA, which is used
for memory freeing at device unbind method.
As for other udevice's fields, a complementary function is added:
- dev_get_uclass_platdata()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the uclass-internal functions by:
- uclass_find_first_device()
- uclass_find_next_device()
For both functions, the returned device is not probed.
After some cleanup, the above functions are called by:
- uclass_first_device()
- uclass_next_device()
for which, the returned device is probed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Initial filesystem images are generally highly compressible.
Add a routine gzwrite that allows gzip-compressed images to be
written to block devices.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch extracts all baseboard specific defines into a separate config file.
This makes it easier to add other baseboards that use the TQMa6 SoM.
This patch will be used by the upcoming WRU-IV board support which also
uses the TQMa6 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Markus Niebel <Markus.Niebel@tq-group.com>
The LDO_EN is bit 4, not value 4. This is only used on the Ventana boards so
we will change it in the header as the other values there are in terms of
values and not bit numbers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added support in default boot scripts to find kernel/dtbs on a boot volume
separate from rootfs volume.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the 'i2c edid' command to query and display data from an attached
HDMI monitor of LVDS display with an EDID device.
Example:
Ventana > i2c dev 2 && i2c edid 0x50
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for the USB mass storage gadget to enable access to on-board
storage.
Example:
Ventana > ums 0 mmc 0 # provide ums access to the uSD
Ventana > ums 0 usb 0 # provide ums access to the first USB device
Ventana > ums 0 sata 0 # provide ums access to an mSATA device
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks Ventana boards don't all use IMX6 FEC, so lets define default
ethprime based off the first detected device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I've encountered issues when using 4k packets through certain switches. For
now disable this and go back to using MTU size packets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add 'fdt_fixup_display' function to fixup device-tree native-mode property
of display-timings node to select timings for a specific display.
This is useful if a device-tree has configurations for multiple
display timings for undetectable displays.
see kernel Documentation/devicetree/bindings/video/display-timing.txt
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix typos and too big #ifdef.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Correct the macros as per insertion of array fast read
command CMD_READ_ARRAY_FAST in spi_read_cmds_array in file
sf_probe.c
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following affected SOCs and their personalities for USB
Erratum A007792 :
T1040 Rev 1.1
T1024 Rev 1.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
U-Boot on this board grew a long time ago past the 384 KiB that
it reserves for the U-Boot image, before the environment. Thus,
saveenv overwrites the U-Boot image and bricks the board.
I tried to find out when U-Boot grew beyond this point, but there is a
long stretch in the history where this board did not build -- and
AFAICT when it did fit in 384 KiB, it was missing vital features such
as fdt support. Turning off CONFIG_VIDEO was not enough to make it
fit. Thus, I don't think we have any choice other than to move the
environment.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_PHY_AQ1202 is no longer needed, use CONFIG_PHY_AQUANTIA.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot does not have system calls (the services it exposes to
standalone commands use a different mechanism), so the syscall handler
is dead code. It's also broken code, as it assumes it is located at
0xc00 -- while even before the patch to stop relocating exception
vectors to 0, U-Boot had the syscall at 0x900.
The critical and machine check return paths are never called -- the
regular exception return path is used instead, which works because
xSRR0/1 have already been saved and can be restored via the regular
SRR0/1 (we don't care too much in U-Boot about taking a critical/mcheck
inside another exception prolog/epilog).
Also remove a few other small unused functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Booke does not require exception vectors to be located at address zero.
U-Boot was doing so anyway, simply because that's how it had been done
on other PPC. The downside of this is that once the OS is loaded to
address zero, the exception vectors have been overwritten -- which
makes it difficult to diagnose a crash that happens after that point.
The IVOR setup and trap entry code is simplified somewhat as a result.
Also, there is no longer a need to align individual exceptions on 0x100
byte boundaries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB.
Enable CONFIG_CMD_MEMTEST as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Now cortina driver uses macro CONFIG_SYS_CORTINA_FW_IN_NOR
to define that firmware of cortina driver is stored in the
nor flash.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
QEMU 2.3 changes the address layout of the CCSR map in the PV ppce500 machine
to reside in higher address space.
Unfortunately, this exposed a glitch in u-boot for ppce500: While providing
a function to dynamically evaluate the CCSR region's position in physical
address space, we never used it. Plus we forgot to support 64bit physical
addresses.
This patch fixes that mishap, making u-boot work fine with latest QEMU again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Make the sandbox setup more generic/examplary by including
config_distro_defaults.h and config_distro_bootcmd.h.
Among other things this makes it easy to test whether images will boot
though with the standard distro bootcmds by running e.g:
u-boot -c 'host bind 0 myimage.img ; boot'
By default there are 2 target host devices to emulate device with
multiple storage devices (e.g. internal ("host 0") and external
("host 1") and verify that the prioritization and fallbacks do work
correctly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Define default PXE client architecture identifiers for IA32 (0x0 aka
Intel x86PC) and Intel x86-64 (0x9 aka EFI x86-64).
This prepares for usage for config_distro_defaults in the sandbox
architecture
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Define the common shared block environment for the host interface in
preperation for the sandbox build to use config_distro_bootcmd.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
More net features enabled and supported on sandbox to allow more testing
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit fixes incorrect DHCP/BOOTP packet layout caused by
'ulong' type size difference on 64 and 32-bit architectures.
It also renames NetReadLong()/NetCopyLong() to
net_read_u32/net_copy_u32() accordingly.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
There were still a few remaining complains in the legacy eth_device
definition that hadn't been addressed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within common/cmd_net.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within dns.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within cdp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove CamelCase variable naming.
Move the definition to the same compilation unit as the primary use.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
The variables around the bootfile were inconsistent and used CamelCase.
Update them to make the code more readable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
As well as running all tests, it is useful to be able to run a selected test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Enable USB emulation and associated features so that USB can be used in
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a few more shifts/masks to make it easier to decode a pipe value (rather
than just building it). We need this for USB device emulation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This is useful for creating lists of descriptors, and is better than using
void * for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
All USB controllers need a root hub. Add a sandbox emulation for this so
that we can add USB devices to sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This emulator supports USB enumeration and allows a local file to be provided
as the contents of the emulated flash stick. U-Boot can then use the file as
it would a normal device, with all access passing through the usb_stor layer
and the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With sandbox we want to be able to emulate USB devices so that we can test
the USB stack. Add a uclass to support this. It implements the same
operations as a normal USB device driver, but in this case passes them on
to an emulation driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This is needed for sandbox USB device emulation, so move it to a place
where it can be found by things other than gadgets.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present USB devices with no driver model driver cannot be seen in the
device list, and we fail to set them up correctly. This means they cannot
be used.
While having real drivers that support driver model for all USB devices
is the eventual goal, we are not there yet.
As a stop-gap, add a generic USB driver which is bound when we do not have
a real driver. This allows the device to be set up and shown on the bus.
It also allows ad-hoc code (such as usb_ether) to find these devices and
set them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
USB devices in U-Boot are currently probed only after all devices have
been enumerated. Each type of device is probed by custom code, e.g.:
- USB storage
- Keyboard
- Ethernet
With driver model this approach doesn't work very well. We could build
a picture of the bus and then go back and add the devices later, but
this means that the data structures are incomplete for quite a while.
It also does not follow the model of being able to bind a device when we
discover it.
We would prefer to have devices automatically be bound as the device is
enumerated. This allows us to attach drivers to particular USB classes
or product/vendor IDs. This is the method used by Linux.
Add the required #defines from Linux, a way of declaring a USB driver and
the logic to locate the correct driver given the USB device's descriptors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are better off in a header file so they can be used by other code (e.g.
the sandbox USB storage emulator).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust the existing hub code to support driver model, and add a USB driver
for hubs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Move the port reset code into its own function. Rename usb_hub_reset() to
indicate that is is now a legacy function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function returns NULL on error at present. Adjust it so that we can
return a real error, as is needed with driver model. Also improve the
error handling in its caller, usb_hub_port_connect_change(), and adjust
the code order to prepare for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a uclass that can represent a USB controller. For now we do not create
devices for things attached to the controller. This will be added later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add some utility functions to check for children and for the last sibling in
a device's parent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The existing get_get_of_data() function provides access to both the driver's
compatible string and its driver data. However only the latter is actually
useful. Update the interface to reflect this and fix up existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The driver is not modified by driver model, so update driver_bind() to
recognise that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some driver want to put DMA buffers in their private data. Add a flag
to tell driver model to align driver-private data to a cache boundary so
that DMA will work correctly in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Once declared, you cannot access a linker_list entry since you do not have
a symbol name for it. Add llsym() macro to provide this. This avoids
searching for the symbol at run-time based on name.
An example usage is to declare a driver with U_BOOT_DRIVER(), then obtain
a pointer to that driver later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some drivers need a chance to manage their receive buffers after the
packet has been handled by the network stack. Add an operation that
will allow the driver to be called in that case.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-on: pcduino3
The U-Boot device trees are slightly different in a few places. Adjust them
to remove most of the differences. Note that U-Boot does not support the
concept of interrupts as distinct from GPIOs, so this difference remains.
For sandbox, use the same keyboard file as for ARM boards and drop the
host emulation bus which seems redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) is on the PCI bus, so show it as such.
The LPC (Low Pin Count) and SPI bus are inside the PCH, so put these in the
right place also.
Rename the compatible strings to be more descriptive since this board is the
only user. Once we are using driver model fully on x86, these will be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 systems this device is commonly used to provide legacy port access.
It is sort-of a replacement for the old ISA bus.
Add a uclass for this, and allow it to have child devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Take a pass at plumbing errors through to the users of the network stack
Currently only the start() function errors will be returned from
NetLoop(). recv() tends not to have errors, so that is likely not worth
adding. send() certainly can return errors, but this patch does not
attempt to plumb them yet. halt() is not expected to error.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow network devices to be referred to as "eth0" instead of
"eth@12345678" when specified in ethact.
Add tests to verify this behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox driver will now generate response traffic to exercise the
ping command even when no network exists. This allows the basic data
pathways of the DM to be tested.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stop forcing drivers to call net_process_received_packet() - formerly
called NetReceive(). Now the uclass will handle calling the driver for
each packet until the driver errors or has nothing to return. The uclass
will then pass the good packets off to the network stack by calling
net_process_received_packet().
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Take the opportunity to enforce better names on newly written or
retrofitted Ethernet drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
On some archs masking the parameter is inefficient, so don't use u8.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some things around and organize things so that the driver model
implementation will fit in more easily.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many of the functions in net.h were preceded extern needlessly. Removing
them to limit the number of checkpatch.pl complaints.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current implementation exposes the eth_device struct to code that
needs to access the MAC address. Add a wrapper function for this to
abstract away the pointer for this operation.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes, for example if the display is mounted in portrait mode or even if it
is mounted landscape but rotated by 180 degrees, we need to rotate our content
of the display respectively the framebuffer, so that user can read the messages
which are printed out.
For this we introduce the feature called "CONFIG_LCD_ROTATION", this may be
defined in the board-configuration if needed. After this the lcd_console will
be initialized with a given rotation from "vl_rot" out of "vidinfo_t" which is
provided by the board specific code.
If CONFIG_LCD_ROTATION is not defined, the console will be initialized with
0 degrees rotation.
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
[agust: fixed 'struct vidinfo' has no member named 'vl_rot' errors]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Since sandbox does not have real devices (unless it borrows those from the
host) it must use emulations. Provide a uclass which permits PCI operations
to be passed through to an emulation device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a uclass for PCI controllers and a generic one for PCI devices. Adjust
the 'pci' command and the existing PCI support to work with this new uclass.
Keep most of the compatibility code in a separate file so that it can be
removed one day.
TODO: Add more header file comments to the new parts of pci.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model will share many functions with the existing PCI implementation.
Move these into their own file to avoid duplication and confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some uclasses want to set up a device before it is probed. Add a method
for this.
An example is with PCI, where a PCI uclass wants to set up its private
data for later use. This allows the device's uclass() method to make calls
whcih use that data (for example, read PCI memory regions from device
tree, set up bus numbers).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function returns -ENOENT when the property is missing (which the caller
might forgive) and also when the property is present but incorrectly
formatted (which many callers would like to report).
Update the error return value to allow these different situations to be
distinguished.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since driver model is set up after arch_cpu_init(), that function cannot
use drivers. Add a new arch_cpu_init_dm() function which is called
immediately after driver model is ready, and can reference devices.
This can be used to probe essential devices for the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is missing a prototype but is more widey useful. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support running U-Boot as a coreboot payload. Tested peripherals include:
- Video (HDMI and DisplayPort)
- SATA disk
- Gigabit Ethernet
- SPI flash
USB3 does not work. This may be a problem with the USB3 PCI driver or
something in the USB3 stack and has not been investigated So far this is
disabled. The SD card slot also does not work.
For video, coreboot will need to run the OPROM to set this up.
With this board, bare support (running without coreboot) is not available
as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since Chromebooks mostly have similar configuration, put it in a common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.
Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a single driver for both USB2 PHY programming and USB3 PHY
programming.
USB3 PHY is taken from drivers/phy/phy-ti-pipe3.c in linux kernel.
commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload.
USB2 PHY is taken from drivers/phy/phy-omap-usb2.c in linux kernel.
commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe
failure and remove.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added an API to check for interrupt status. This API is generally
called from board file to check for interrupt status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 omap controllers. This gives uboot
the capability to control multiple dwc3 omap controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.
This will change once we have dwc3-omap driver adapted to use the uboot
driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 omap platform data. The board file should
populate these platform data before invoking dwc3 omap driver.
This will be removed once dwc3-omap driver is adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the included header files to that used in u-boot.
*) Removed extcon_* APIs
*) Removed regulator_* APIs
*) Fixed other misc warnings
*) Added dwc3-omap.h to include the definitions of UTMI modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Since interrupt support is not present in u-boot, added an
API to handle the interrupts in dwc3 core. This API can be
polled to handle the interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 controllers. This gives uboot
the capability to control multiple dwc3 controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 core platform data. The board file should
populate these platform data before invoking dwc3 driver.
This will be removed once we have dwc3 driver adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added USB_GADGET_DELAYED_STATUS to avoid the following compilation error.
error: ‘USB_GADGET_DELAYED_STATUS’ undeclared (first use in this function)
while compiling dwc3/ep0.c
While this is been added only to avoid compilation error, the complete fix
should be something like the one added in linux kernel. The complete fix
will be ported once we have the composite driver in u-boot look similar to
the one in linux kernel.
commit 1b9ba000177ee47bcc5b44c7c34e48e735f5f9b1
Author: Roger Quadros <roger.quadros@nokia.com>
Date: Mon May 9 13:08:06 2011 +0300
usb: gadget: composite: Allow function drivers to pause control transfers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Did a bunch of things to get dwc3/gadget.c compile in u-boot without
build errors and warnings
*) Changed the included header files to that used in u-boot.
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) removed sg support
*) remove jiffies and used a simple while loop
*) removed irq support and added a function to call these interrupt handler.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Changed the header files included in core.h and io.h to the u-boot header
files so that these files can be included in other dwc3 source files and
be compiled in uboot. Also added otg.h which has the defines for dr_mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Made changes in gadget.h that is required after adding udc-core.c
except changes that might break other platforms.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
On some SoCs, DMA-capable peripherals see a different address space to
the CPU's physical address space. Create an API to allow platform-agnostic
drivers to convert between the two address spaces when programming DMA
operations.
This API will exist on all platforms, but will have a dummy implementation
when this feature is not required. Other platforms will enable
CONFIG_PHYS_TO_BUS and provide the required implementation.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This patch converts USB protocol headers to use explicitly sized
fields like the rest of the code
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
This consolidates the flash settings for the Integrator
and activates the new ARM flash image support for them
so images can be loaded by name from flash.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This modifies the vexpress64 Juno configuration so that
it will by default load and boot a kernel and a device tree
from the images stored in the NOR flash. When we are
at it, also define the proper command line for the Juno and
indicate that the USB stick (/dev/sda1) is the default
root file system.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
- EEPROM (24M01-compatible)
- RTC (DS1374-compatible)
- Temperature sensor (DS620)
- DACs (2 x MAX518)
- SPI (through SSP interface)
- Port expander MAX6957
- LCD display (HD44780-compatible), controlled
through the port expander and DACs
This board has SPL support, and uses the LPC32XX boot
image format.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
There're 2 versions of motherboards that could be used in ARC SDP.
The only important difference for U-Boot is different NAND IC in use:
[1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP
while
[2] v3 board sports MT29F4G16ABADAWP
They are almost the same except data bus width 8-bit in [1] and 16-bit
in [2]. And for proper support of 16-bit data bus we have to pass
NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing
board type we're running on.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.
http://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Since commit 32df39c741 ("mx5: fix get_reset_cause") we have the following
boot messages on a mx53qsb:
U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
CPU: Freescale i.MX53 rev2.1 at 1000 MHz
Reset cause: unknown reset
Net: FEC [PRIME]
The CPU and Reset cause lines appear twice.
Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via
I2C to raise the CPU voltage so that it can run at 1GHz.
To avoid such misleading double printings, disable printing cpu info for now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
After this change it is possible to boot trats2 device with Image.itb,
which facilitates automated testing, since only one file is necessary.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After this change it is possible to boot trats device with Image.itb,
which facilitates automated testing, since only one file is necessary.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change allows using Image.itb image format with Exynos4 devices
(especially trats and trats2).
Such change facilitates automated testing since only one binary needs
to be prepared.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The peach boards have their SDRAM start address at 0x20000000 instead of
0x40000000 which seems common for all other exynos5 based boards. This
means the layout set in exynos5-common.h causes the kernel be loaded
more then 128MB (at 0x42000000) away from memory start which breaks
booting kernels with CONFIG_AUTO_ZRELADDR
Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses
the same offsets from start of memory as the common exynos5 settings.
This fixes booting via bootz and PXE
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We can enable / disable trace feature from the FTRACE config options.
To enable, compile U-Boot with FTRACE=1.
This patch add #ifdef FTRACE in exynos5-common.h for enable/disable
to use FTRACE configs instead of having to change board config files.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Simon Glass <sjg@chroimum.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
