This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The MSI Primo81 tablet has B079XAN01/LP079X01 7.85" 768x1024 IPS
MIPI display, connected to the parallel LCD interface via SSD2828
bridge chip. The panel has 18-bit color depth and needs dithering,
in spite of having RGB data delivered from A31s to SSD2828 using
24-bit arrangement.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we've separate detailed dram settings for all sun4i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
Tested-by: Hans de Goede <hdegoede@redhat.com> on a A10-OLinuXino-Lime,
Chuwi_V7_CW0825 and ba10_tv_box
Tested-by: Zoltan HERPAI <wigyori@uid0.hu> on a pcduino
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds the new Barco platinum platform. It currently
includes those two boards:
platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.
platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
Add missing T1024QDS_defconfig for NOR boot on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure boot target is added for T1042RDB platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR and SPI flash secure boot target for C29XPCIE board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The Hummingbird A31 uses an external DAC connected to the LCD0 outputs
for the on board VGA output. The DAC has a power control that's toggled
by GPIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable the new LCD support on Ippo_q8h tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Enable VGA output on the A13-OLinuXino and A13-OLinuXinoM now that we've
support for it.
Also add LCD timing and gpio info for the Olimex 7" LCD module. We can safely
put this in the default config on this boards, since by default we will always
use VGA, and the LCD timing info will only get used if the user explicitly
sets monitor=lcd in the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch uses the same DRAM settings as in the pre-installed
Android firmware. The LCD display is supported too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch uses the same ZQ and DRAM clock settings as in the
pre-installed Android firmware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We need separate defconfigs for the v5 and v1.2 versions of this board, as
they use different DRAM parameters.
Note they also use different dtb files, as the wifi is different too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we've sun8i dram-init support we can enable the SPL for sun8i boards.
While at it also replace CONFIG_DEFAULT_DEVICE_TREE with CONFIG_FDTFILE,
the former is for u-boot's own fdt usage, which we do not use (yet), the later
specifies the fdt to pass to the kernel, which is the one we want.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some of the ldo-s of the axp221 are used in the same way on most boards, add
comments to the Kconfig help text to reflect this, and give them defaults
matching their typical usage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Merrii Hummingbird A31 is a A31 based development board with 1G
RAM, 8G NAND, AP6210 WiFi+BT, gigabit ethernet, USB OTG, 2 USB 2.0
ports connected to a USB hub chip, HDMI, VGA, TV and stereo in/out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Colombus defconfig settings are missing a number of settings for recently
added features, because we did not know exactly how things were hooked up.
Maxime Ripard has run various tests to get us the necessary details, this
commit updates the defconfig with this info.
This commit also updates the dram clk and zq values with values verified
by Maxime to be the ones used by the original firmware for this board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.
Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.
Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.
To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
'+S' is unnecessary because boards of rmobile do not use SPL.
This removes from armadillo-800eva and kzm9g.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for Odroid-XU3.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
