Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h, after which this part of
rpi_b.h was modelled.
The #defines to enable/disable U-Boot commands/features were moved
earlier in rpi_b.h, so they are set up before config_distro_bootcmd.h
is included, since it tests whether certain features should be included
based on those defines.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
After the clean up performed in the commit 1151b7ac10b81ecbb the DFU subsystem
requires absolute patch for correct operation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
echi-rmobile does not support xHCI. This removes xHCI address
from address table. And this revise a value of CONFIG_USB_MAX_CONTROLLER_COUNT
for lager board and koelsh board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Enable CONFIG_SYS_GENERIC_BOARD for the i.MX31 PDK board.
Tested on actual hardware.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
A previous update to the I2C stack introduced a typo in the
configuration option. Fix the typo and therefore allow the
RTC to work correctly with the 'date' command again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
- move blackfin specific cpu init code from blackfin board.c to cpu.c
- remove blackfin specific board init code and invoke generic board_f fron cpu init entry
- rename section name bss_vma to bss_start in order to match the generic board init code
- add a fake relocate_code function to set up the new stack only
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
The booting of the board is now protected by the CPU watchdog.
A failure during the boot phase will end up in board reset.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CNTFRQ needs to be properly configured on all CPUs. Otherwise,
virtual machines hoping to find valuable information on secondary
CPUs will be disapointed...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
So far, only supporting the CPU_ON method.
Other functions can be added later.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Specific USB EHCI settings to be set for sun5i if CONFIG_USB_EHCI is enabled.
Note we don't specify default VBUS gpio pins for sun5i since they vary too
much from board to board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Specific USB EHCI settings to be set for sun4i if CONFIG_USB_EHCI is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Specific USB EHCI settings to be set for sun7i if
CONFIG_USB_EHCI is enabled.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Use SUNXI_GPH macro for SUNXI_USB_VBUS#_GPIO]
[hdegoede@redhat.com: Add #ifndef SUNXI_USB_VBUS#_GPIO to allow override of
the default pins from boards.cfg]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
General configuration settings to be set if CONFIG_USB_EHCI
is enabled for an Allwinner aka sunxi SoC.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.
Remove the redundant definition in config headers.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.
In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.
CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
warning: "CONFIG_SPL" redefined [enabled by default]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO: individual board config files using these configs.
So that each board can independently set the value as per its design.
Following configs are affected in this patch:
CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>
This patch also updates documentation for few of above NAND configs.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Fixes commit a0a37183bd
ARM: omap: merge GPMC initialization code for all platform
1) NAND device are not directly memory-mapped to CPU address-space, they are
indirectly accessed via following GPMC registers:
- GPMC_NAND_COMMAND_x
- GPMC_NAND_ADDRESS_x
- GPMC_NAND_DATA_x
Therefore from CPU's point of view, NAND address-map can be limited to just
above register addresses. But GPMC chip-select address-map can be configured
in granularity of 16MB only.
So this patch uses GPMC_SIZE_16M for all NAND devices.
2) NOR device are directly memory-mapped to CPU address-space, so its
address-map size depends on actual addressable region in NOR FLASH device.
So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
size configuration.
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds a common config header file for all the Keystone II
EVM platforms. It combines a lot of general definitions in one file.
The common header included in the EVM should be specific configuration
header.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.
The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.
The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.
Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
The alt board has R8A7794, 1GB DDR3-SDRAM, USB, Ethernet, QSPI,
MMC, SDHI and more.
This commit supports the following functions:
- DDR3-SDRAM
- SCIF
- I2C
- Ethernet
- QSPI
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds the changes to boards.cfg and the board directory
under board/tqc.
TQMa6 is a family of modules based on Freescale i.MX6. It consists of
TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3
TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3
The modules need a baseboard. Initially the MBa6x starterkit mainboard is
supported. To easy support for other mainboards the functionality is splitted
in one file for the module (tqma6.c) and one file for the baseboard (tqma6_
mba6).
The modules can be boot from eMMC (on USDHC3) and SPI flash.
The following features are supported:
- MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard)
- Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module.
The phy needs special configurations for the pad skew registers to adjust for
the signal routing.
Also support for standard ethernet commands and uppdate via tftp.
- SPI: ECSPI1 with bootable serial flash on module and two additional
chip selects on MBa6x
- I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3)
and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x
are also configured.
- USB: high speed host 1 on MBa6x and support for USB storage
- PMIC: support for pfuze 100 on TQMa6<x>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
As a result of 0defddc851 , which did
a consolidation of the prompt string, this ifdef became empty. Remove
it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
- Fix base address of I2C2 as 0x118100 instead of 0x119000.
- Add definitions for I2C3 & I2C4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove unnecessary condition CONFIG_RAMBOOT_PBL to
have SST and EON SPI flash work in case of NOR boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board is close in binary size to one of its hard limits, so disable
SHA256 FIT image support to gain some breathing room.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM
boards, the sunxi SoCs have a NIC onboard without an embedded MAC address.
Just like the omap used on these boards, the sunxi SoCs do have a unique chip
id, in the form of the 128 bit SID register:
http://linux-sunxi.org/SID_Register_Guide
So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id
to generate a unique fixed MAC address.
We check for the SID not being all 0, since some early A20 batches
shipped without having there SID programmed.
Note we use specific parts of the 128 bits, since some parts indicate the
SoC family / revision, and thus are fixed. The algorithm for this was taken
from the linux-sunxi.org kernels.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[hdegoede@redhat.com: Expanded the commit message with some more info]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.
And enable AXP209 support for the Cubietruck and Cubieboard boards.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
Timer on cyclone5 actually counts down. It took me a while to figure
out, as timer counting in wrong direction actually _can_ be used, it
just appears to tick at extremely high frequency in u-boot.
The bug was introduced in commit
23ab7ee0ff.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Adjust the mtdparts settings to allow for alternative boot images and
for using UBI.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
- "env ask", "env grep" and "setexpr" are needed for commissioning
- add support for ext4 file systems
- adjust default environment to use ext4 commands
- add write support for (V)FAT and EXT4
- add bitmap and splashscreen support
- print timestamp information for images
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
- "env ask", "env grep" and "setexpr" are needed for commissioning
- add support for ext4 file systems
- adjust default environment to use ext4 commands
- add write support for (V)FAT and EXT4
- add bitmap and splashscreen support
- print timestamp information for images
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The following patch re-enables the dhcp functionality on omap3_beagle.
It was removed with df4dbb5df6 when
omap3_beagle was converted to use ti_omap3_common.h. I have tested
beagleboard and beagleboard-xm with this patch and confirmed dhcp is
working.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Commit "2842c1c fit: add sha256 support" badly increased
memory footprint, so some of our boards did not build anymore.
Since monitor base must not be changed I removed some commands
to save memory.
Maybe making sha256 optional for fit would be an option for
the future since it really has some beefy footprint.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default.
Allow EDID only to avoid I2C address conflicts.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Use get_device_and_partition() is better since:
1. It will call the device initialize function internally. So we can
remove the mmc intialization code to save many lines.
2. It is used by fatls/fatload/fatwrite. So saveenv & load env should
use it too.
3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct
device and partition information by run-time.
Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string:
FAT_ENV_DEVICE_AND_PART.
For at91sam9m10g45ek, it is "0". That means use device 0 and if:
a)device 0 has no partition table, use the whole device as a FAT file
system.
b)device 0 has partittion table, use the partition #1.
Refer to the commit: 10a37fd7a4 for details of device & partition string.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add support for the Allwinner A13 and A10s SoCs also know as the Allwinner
sun5i family, and the A13-OLinuXinoM A13 based and r7-tv-dongle A10s based
boards.
The only differences compared to the already supported sun4i and sun7i
families are all in the DRAM controller initialization:
-Different hcpr values
-Different MBUS settings
-Some other small initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the Allwinner A10 SoC also known as the Allwinner sun4i family,
and add the Cubieboard board which uses the A10 SoC.
Compared to sun7 only the DRAM controller is a bit different:
-Controller reset bits are inverted, but only for Rev. A
-Different hpcr values
-No MBUS on sun4i
-Various other initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
