AT91CAP9 and AT91SAM9 SoCs are very close hardware wise, so a
common infrastructure can be used. Let this infrastructure be
named after the AT91SAM9 family, and move the existing AT91CAP9
files to the new place.
Signed-off-by: Stelian Pop <stelian@popies.net>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.
Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 5013c09f (Makefile: cleanup "clean" target) introduced a
problem for out-of-tree builds which caused "make clean" to fail.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
If any of the steps for generating autoconf.mk fail currently, they go
unnoticed. To fix, we can simply add 'set -e' to the long list of commands.
This is simpler and more robust than placing '|| exit $$?' after every line.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By adding VERSION_FILE to the PHONY targets the script
/tools/setlocalversion is always called and version_autogenerated.h
is replaced only if the script find a modified source file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
If the $(LDSCRIPT) does not exist (normally it's board/$(BOARD)/u-boot.lds),
then change into the board directory and try and create it. This allows you
to generate the linker script on the fly based upon board defines (like the
Blackfin boards do).
There should be no regressions due to this change as the normal case is to
already have a u-boot.lds file. If that's the case, then there's nothing to
generate, and so make will always exit. The fix here is that if the linker
script does not exist, the implicit rules take over and attempt to guess how
to generate the file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Constantly rebuilding the version header will force useless relinking, so we
simply need to compare the new header with the existing one before updating
it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch enables the OneNAND boot within U-Boot.
Before this work, we used another OneNAND IPL called X-Loader based
on open source. With this work, we can build the oneboot.bin image
without other program.
The build sequence is simple.
First, it compiles the u-boot.bin
Second, it compiles OneNAND IPL
Finally, it becomes the oneboot.bin from OneNAND IPL and u-boot.bin
The mechanism is similar with NAND boot except it boots from itself.
Another thing is that you can only use the OneNAND IPL only to work
other bootloader such as RedBoot and so on.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
- Add inline helper macros for basic header processing
- Move common non inline code common/image.c
- Replace direct header access with the API routines
- Rename IH_CPU_* to IH_ARCH_*
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This fixes a build breakage with CONFIG_API enabled, which appeared after
the recent changes in the U-Boot build system.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hi,
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With serial, NE2000, IDE support. Tested in big-endian mode.
Memory size hard-coded to 128M for now, so don't play with
the -m option.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- get rid of "version" target whichdidn't really work
- make autoconf.mk depend on version_autogenerated.h to make sure
to rebuild files as needed
- add XECHO macro to allow for silent build using "make -s"
Signed-off-by: Wolfgang Denk <wd@denx.de>
The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for Wind River's SBC8548 reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>
This is an API for external (standalone) applications running on top of
U-Boot, and is meant to be more extensible and robust than the existing
jumptable mechanism. It is similar to UNIX syscall approach. See api/README
for more details.
Included is the demo application using this new framework (api_examples).
Please note this is still an experimental feature, and is turned off by
default.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
This patch updates the fw_printenv/fw_setenv userspace tool to include
the correct MTD header in order to compile against current kernel
headers. Backward compatibility is preserved by introducing an option
MTD_VERSION which can be set to "old" for compilation using the old MTD
headers. Along with this a number of warnings are fixed.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
The bash builtin versions of the "test" (resp. "[") command allow
using "==" for string comparisons, but POSIX compatible implemen-
tations (like /usr/bin/test) insist on using "=" only. On such systems
you will see:
$ /usr/bin/test a == a && echo OK
/usr/bin/test: ==: binary operator expected
This patch fixes Makefiles and scripts to use POSIX style.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These patches add support for the PPC440EPx-based "Korat" board to
U-Boot. They are based primarily on support for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SoC-specific code for all the AT32AP700x CPUs is practically
identical; the only difference is that some chips have less features
than others. By doing this rename, we can add support for the AP7000
derivatives simply by making some features conditional.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use cpp and sed to postprocess config.h and import the defined values
into include/autoconf.mk. autoconf.mk is then included by config.mk to
give 'make' access to the board configuration.
Doing this enables conditional compilation at the Makefile level instead
of by wrapping every .c file with #ifdef/#endif wrappers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
