At present a ulong is used to hold operand values. This means that
strings cannot be used. While most operations are not useful for strings,
concatenation is. As a starting point to supporting strings, convert the
code to use a struct instead of a ulong for operands.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when more than one substitution is made this function
overwrites its buffers. Fix this bug and update the tests now that they
can pass.
Also update the debug code to show all substrings, since at present it
omits the final one.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the 'nlen' variable increases with each loop. If the previous
loop had back references, then subsequent loops without back references
use the wrong value of nlen. The value is larger, meaning that the string
terminator from nbuf is copied along to the main buffer, thus terminating
the string prematurely.
This leads to the final result being truncated, e.g. missing the last
(unmatched) part of the string. So "match match tail" become
"replaced replaced" instead of "replaced replaced tail".
Fix this by resetting nlen to the correct value each time around the lop.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests to check for buffer overflow using simple replacement as well
as back references. At present these don't fully pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function always allocates a large amount of stack, and
selects its own size for buffers. This makes it hard to test the code
for buffer overflow.
Separate out the inner logic of the substitution so that tests can call
this directly. This will allow checking that the algorithm does not
overflow the buffer.
Fix up one of the error lines at the same time, since it should be
printing nbuf_size, not data_size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests for the setexpr regex commands.
Note that these tests currently crash on sandbox due to an existing bug in
the setexpr implementation, so two of the tests are commented out.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function assumes that a size of 4 refers to a ulong. This
is true on 32-bit machines but not commonly on 64-bit machines.
This means that the 'l' specify does not work correctly with setexpr.
Add an explicit case for 32-bit values so that 64-bit machines can still
use the 'l' specifier. On 32-bit machines, 64-bit is still not supported.
This corrects the operation of the default size (which is 4 for setexpr),
so update the tests accordingly.
The original code for reading from memory was included in 47ab5ad145
("cmd_setexpr: allow memory addresses in expressions") but I am not adding
a Fixes: tag since that code was not written with 64-bit machines in mind.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these values are open-coded in a few places. Add constants so
the meaning is clear.
Also add a comment to cmd_get_data_size()
Signed-off-by: Simon Glass <sjg@chromium.org>
This command currently has no tests. Add some for basic assignment and the
integer operations.
Note that the default size for setexpr is ulong, which varies depending on
the build machine. So for sandbox on a 64-bit host, this means that the
default size is 64 bits.
Signed-off-by: Simon Glass <sjg@chromium.org>
On more places is used pattern 'command > $@ || rm -f $@'. But it does not
propagate failure from 'command' as 'rm -f' returns success.
Fix it by calling 'false' to correctly propagate failure after 'rm -f'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
- ProxyDHCP allows a second DHCP server to exist alongside your main
DHCP server and supply additional BOOTP related options
- When u-boot sends out a DHCP request, the real DHCP server will
respond with a normal response containing the new client IP address
while simultaneously the ProxyDHCP server will respond with a blank
client IP address and a `bootfile` option
- This patch adds CONFIG_SERVERIP_FROM_PROXYDHCP (default false) to
enable this behavior and CONFIG_SERVERIP_FROM_PROXYDHCP_DELAY_MS
(default 100) which tells u-boot to wait additional time after
receiving the main DHCP response to give the ProxyDHCP response time
to arrive
- The PXE spec for ProxyDHCP is more complicated than the solution
added here as diagramed on page 16:
http://www.pix.net/software/pxeboot/archive/pxespec.pdf:
```
DHCP Discover will be retried four times. The four timeouts are 4, 8, 16
and 32 seconds respectively. If a DHCPOFFER is received without an Option
timeouts in an attempt to receive a PXE response.
```
- Adding a simple delay worked for my purposes but let me know if a
more robust solution is required
Signed-off-by: Lyle Franklin <lylejfranklin@gmail.com>
As FDTDIR label doesn't specify exact file to be loaded, it should
not fail if no file exists in the directory. In this case try to boot
with internal FDT if it exists.
Signed-off-by: Anton Leontiev <aleontiev@elvees.com>
The following errors are corrected:
* Linux crash when accessing UEFI variables at runtime.
* UEFI variable using standalone MM on 32 bit systems
not working due to missing packing of communication
structure
* NULL dereference when FAT16 root directory is full
* FAT files with a short file name starting with 0xE5 (0x05 in directory
entry) where treated as deleted.
The UEFI SetTime() service is enabled on ARM QEMU.
-----BEGIN PGP SIGNATURE-----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=CgpH
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc3-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (3)
The following errors are corrected:
* Linux crash when accessing UEFI variables at runtime.
* UEFI variable using standalone MM on 32 bit systems
not working due to missing packing of communication
structure
* NULL dereference when FAT16 root directory is full
* FAT files with a short file name starting with 0xE5 (0x05 in directory
entry) where treated as deleted.
The UEFI SetTime() service is enabled on ARM QEMU.
commit 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()")
introduces a check using u16_strnlen(). This code is used on EFI
runtime variables as well, so unless we mark it as runtime, the kernel
will crash trying to access it.
Fixes: 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Pack struct efi_mm_communicate_header as done in EDK2 as seen in
release 201808 [1]. If not packed sizeof() for the structure adds
4 additional bytes on 32bit targets which breaks the ABI.
Link: [1] https://github.com/tianocore/edk2/blob/edk2-stable201808/MdePkg/Include/Protocol/MmCommunication.h#L21
Fixes: 23a397d2e2 ("efi_loader: Add headers for EDK2 StandAloneMM communication")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Enable EFI_SET_TIME on the sandbox and QEMU ARM to ensure that we compile
and test the relevant code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Using constants instead of anonymous numbers increases code readability.
Fixes: 704df6aa0a ("fs: fat: refactor write interface for a file offset")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
0x05 is used as replacement letter for 0xe5 at the first position of short
file names. We must not skip over directory entries starting with 0x05.
Cf. Microsoft FAT Specification, August 30 2005
Fixes: 39606d462c ("fs: fat: handle deleted directory entries correctly")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When trying to create a file in the full root directory of a FAT32
filesystem a NULL dereference can be observed.
When the root directory of a FAT16 filesystem is full fill_dir_slot() must
return -1 to signal that a new directory entry could not be allocated.
Fixes: cd2d727fff ("fs: fat: allocate a new cluster for root directory of fat32")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for the OpenCores I2C controller IP core
(See http://www.opencores.org/projects.cgi/web/i2c/overview).
This driver implementation is inspired from the Linux OpenCores
I2C driver available.
Thanks to Peter Korsgaard <peter@korsgaard.com> for writing Linux
OpenCores I2C driver.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
At present if CONFIG_RESET is not enabled, this code shows a warning:
designware_i2c_ofdata_to_platdata() i2c_designware_pci i2c2@16,0:
Can't get reset: -524
Avoid this by checking if reset is supported, first.
Fixes: 622597dee4 ("i2c: designware: add reset ctrl to driver")
Signed-off-by: Simon Glass <sjg@chromium.org>
The hidden I2C slave is also present on the Armada 8k AP806. Testing
shows that this I2C slave causes the same issues as Armada 38x.
Disabling that I2C slave fixes all these issues.
I2C blocks on the Armada 8k CP110 are not affected.
Extend the I2C slave disable to Armada 8k as well.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Regulator can be set to "always-on".
It's not error about enable/disable. It needs to check about
its condition.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It's useful to know an error number when it's debugging.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400,
db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b ("mmc: fsl_esdhc: support eMMC HS400 mode")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All of the existing quirks add retries to various calls of mmc_send_cmd.
mmc_send_cmd_quirks is a helper function to do this retrying behavior. It
checks if quirks mode is enabled, and if a specific quirk is activated it
retries on error.
This also adds mmc_send_cmd_retry, which retries on error every time
(instead of if a quirk is activated).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Add DHCOM based STM32MP15x PicoITX board
- Correct ALIGN macro usage for on syram for SPL dcache support
- Fixes on DHCOM: uSD card-detect GPIO and Drop QSPI CS2
- Fix compilation issue for spl_mmc_boot_partition
- Fix MTD partitions for serial boot
- Add support of MCU HOLD BOOT with reset for stm32 remoteproc
(prepare alligneent with kernel DT)
- Correct bias information and support in STM32 soc and STMFX
- Support optional vbus in usbphyc
- Update FIT examples to avoid kernel zImage relocation before decompression
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl++X0MACgkQ4rK92eCq
k3UQTQf/VndEkKb/jWxvXPI69g0aGW1CgzkJrOyv5LzR7E7n16Y6sDjnHFqNwqrM
5WWgft0KYY9zb3+Hk92ymD/Z7zKkIWDbp9FlFky3q7rcKe6mpNghtHS6VoiXwcRG
gZro+bM/5QKZUpZOcDB6oRtlKx+IgvKYAtOeURK1zUOkoiwuzoRPYhyEdi/DFFG8
y8ByGBj0SAkv//PKrF+XfS0F5eGJuBrncEfI3+iMtJI/P1fiP/UdySVUK58JkKMJ
hEUwuR7RADL1F0cP7ZQSBOXksLyKf/DpdYt8J52hf1ml3H5BmhWb91sFK58RRw/v
PBGbdoschACauAzbSdEh2sqp8dQG9A==
=ox0A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201125' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- STM32 MCU's DT update
- Add DHCOM based STM32MP15x PicoITX board
- Correct ALIGN macro usage for on syram for SPL dcache support
- Fixes on DHCOM: uSD card-detect GPIO and Drop QSPI CS2
- Fix compilation issue for spl_mmc_boot_partition
- Fix MTD partitions for serial boot
- Add support of MCU HOLD BOOT with reset for stm32 remoteproc
(prepare alligneent with kernel DT)
- Correct bias information and support in STM32 soc and STMFX
- Support optional vbus in usbphyc
- Update FIT examples to avoid kernel zImage relocation before decompression
Update kernel load address for FIT examples to avoid relocation:
- Kernel example uses Image.gz with U-Boot gzip decompression
at final kernel location 0x0xC0008000.
- Copro example loads zImage at a correct location (0xC4000000),
to avoid zImage relocation before decompression by kernel code.
An other solution to avoid zImage relocation is to align
the kernel load and entry address with the real location in FIT
(the relocation of zImage is skipped in U-Boot bootm command for
identical address) but it is less flexible because this offset
depends on FIT content:
For example:
## Loading kernel from FIT Image at c2000000 ...
Using 'ev1' configuration
Trying 'kernel' kernel subimage
Description: Linux kernel
Created: 2020-10-22 9:08:32 UTC
Type: Kernel Image
Compression: uncompressed
Data Start: 0xc20000cc
The kernel offset in FIT is 0xCC in FIT and zImage is decompressed at
0xC0008000 by kernel code:
kernel {
description = "Linux kernel";
data = /incbin/("zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0xC20000cc>;
entry = <0xC20000cc>;
hash-1 {
algo = "sha1";
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update pin name to avoid duplicated name with SOC GPIO
gpio0...gpio15 / agpio0....agpio7: add a stmfx prefix.
This pin name can be used in pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The device name is used in pinmux command and in log trace
so it is better to use the parent parent name ("stmfx@42" for
example) than a generic name ("pinctrl" or "stmfx-gpio")
to identify the device instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the bias configuration for all the GPIO configurations and not
only for input GPIO, as indicated in Reference manual
(Table 81. Port bit configuration table).
Fixes: 43efbb6a3e ("gpio: stm32: add ops get_dir_flags")
Fixes: f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).
Fixes: da7a0bb1f2 ("pinctrl: stm32: add information on pin configuration")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The coprocessor is running as soon as the hold boot is de-asserted.
So indicate this running state and save the resource table even
if the protective assert, to avoid autonomous reboot, is failed.
This error case should never occurs.
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the update of the MTD partitions in kernel device tree
for serial boot (USB / UART), and the kernel will use the MTD
partitions define in the loaded DTB because U-Boot can't known the
expected flash layout in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
spl_mmc_boot_partition is only defined when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is defined.
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The uSD slot card-detect GPIO is connected to PG1, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
