The bcm2711 has two emmc controllers. The difference is the clocks
they use. Add support for the second emmc controller.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
This clock has a different mbox ID so have this included in the relevant
header file.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspebrry Pi 4 uses the new revision code scheme as documented by
the foundation. This change adds an entry for this board as well.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Define two target configs for Raspberry Pi 4 (32 and 64bit) and the
corresponding BCM2838* configs.
Be aware of the current limitation in firmware which requires an
explicit configuration to force the arm in 64bit mode when the
respective target is used.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
[mb: rename BCM2838 -> BCM2711]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Devices of bcm283x have different base address, depending if they are on
bcm2835 or bcm2836/7. Use BCM283x_BASE depending on the SoC you want to
build and only add the offset in the header files.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
This defines a minimum defconfig for each of the two Raspberry Pi 4
variants. One notable difference is that we don't have a embedded dt for
this board given that the fw supplies us with one which we can reuse.
Furthermore, the ram size is not queryable through mbox interface as the
maximum reported size is 1G. The fw patches the dt with the right
memory configuration and uboot uses it as it is. We avoid u-boot
touching this configuration by making sure CONFIG_ARCH_FIXUP_FDT_MEMORY
is deactivated.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
On AArch64, kernel images are not self-decompressing and easily exceed
the 8MB limit.
Signed-off-by: Laurent Bonnans <laurent.bonnans@here.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Function bcm_2835_wait_transfer_complete() is not waiting long enough.
The previous code was claiming to wait for ~1 seconds, but as it depends
on register reads it's time actually varies.
Some cards require wait times of up to ~56 ms to perform
the command 'saveenv' on an EXT4 partition.
Re-implement the loop exit condition to use get_timer() which allows
to specify the wait time in more reliable manner. Set the maximum wait
time to the originally intended 1 second.
Signed-off by: Raul Benet <raul.benet_at_kaptivo.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Before we can send a message to the mailbox we have to check that there
is space to do so. Therefore we poll the status register. But up to now
the wrong status register, the one of mailbox 0, was checked. Fix this
by polling the status regiser of mailbox 1.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[mb: rename registers and update commit message]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This includes the patches from
Pull request for UEFI sub-system for v2019.10-rc4 (2)
Fix UEFI specification compliance issues in the simple network protocol:
* Correctly set and reset the interrupt status.
* Support filling the header in the Transmit() service.
* Correct the checking and setting of the network state.
* Implement the MCastIPtoMAC() service.
* Adjust the simple network protocol unit test.
Fix UEFI specification compliance issues in the protocol.
Fix UEFI specification compliance issues in the simple text output protocol:
* Avoid out of bounds cursor position.
* Do not set illegal screen mode.
Fix UEFI specification compliance issues in the block IO protocol:
* Check parameters.
* Return correct status code if buffer is unaligned.
Refactor initialization of EFI memory in preparation of support for
> 3GB memory on x86.
-----BEGIN PGP SIGNATURE-----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=lu6V
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc4-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (3)
This includes the patches from
Pull request for UEFI sub-system for v2019.10-rc4 (2)
Fix UEFI specification compliance issues in the simple network protocol:
* Correctly set and reset the interrupt status.
* Support filling the header in the Transmit() service.
* Correct the checking and setting of the network state.
* Implement the MCastIPtoMAC() service.
* Adjust the simple network protocol unit test.
Fix UEFI specification compliance issues in the protocol.
Fix UEFI specification compliance issues in the simple text output protocol:
* Avoid out of bounds cursor position.
* Do not set illegal screen mode.
Fix UEFI specification compliance issues in the block IO protocol:
* Check parameters.
* Return correct status code if buffer is unaligned.
Refactor initialization of EFI memory in preparation of support for
> 3GB memory on x86.
The sdhci capabilities registers can be incorrect. The
sdhci-caps-mask and sdhci-caps dt properties specify which bits of
the registers are incorrect and what their values should be. This
patch makes the sdhci driver use those properties to correct the caps.
Also use "dev_read_u64_default" instead of "dev_read_u32_array" for
caps mask.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds functions dev_read_u64_default & dev_read_u64
to read unsigned 64-bit values from devicetree.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We cannot do anything in EFI_BLOCK_IO_PROTOCOL.Reset() but this does not
justify to return an error.
Let EFI_BLOCK_IO_PROTOCOL.Reset() return EFI_SUCCESS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI_PRINT() offers indention of debug messages. Adjust the debug messages
of the BLOCK_IO_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Check parameters of ReadBlocks() and WriteBlocks().
If the buffer size is not a multiple of the block size, we have to return
EFI_BAD_BUFFER_SIZE.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL.SetMode() should return EFI_UNDEFINED if a
screen mode is not available.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
When backspacing in column 0 do no set the column index to ULONG_MAX.
Ensure that the row number is not set to ULONG_MAX even if the row count is
advertised as 0.
Ignore control characters other the 0x08, 0x0a, 0x0d when updating the
column.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Correct the name of the partition size component in struct
efi_device_path_cdrom_path.
Render entry, start, and size when converting a CD-ROM device path node to
text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Vendor device paths may contain data. When converting vendor device paths
to text this binary data has to be rendered.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adding a conventional memory region to the memory map may require ram_top
limitation and it can be also commonly used. Extract adding a conventional
memory to the memory map in a separate routine for generic use.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Implement the MCastIPtoMAC service of the simple network protocol.
It converts an multicast IPv4 (or IPv6) address to a multicast Ethernet
address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The network should start in status EfiSimpleNetworkStopped.
Add and correct status checks in the simple network protocol.
Correct the unit test:
* Shutdown() and Stop() during setup if needed
* invoke Shutdown() before Stop() when tearing down
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fill the media header in EFI_SIMPLE_NETWORK.Transmit().
Check that the buffer size is large enough for the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Check that when the WaitForPacket event occurs
EFI_SIMPLE_NETWORK_RECEIVE_INTERRUPT is set.
Check the return value of Receive().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GetStatus() must clear the interrupt status.
Transmit() should set the TX interrupt.
Receive() should clear the RX interrupt.
Initialize() and Start() should clear the interrupt status.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_CMD_BOOTEFI_SELFTEST for the QEMU RISC-V boards.
Travis CI QEMU testing has been enabled for qemu-riscv64_defconfig. With
this patch we will test the UEFI sub-system on the board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As stated in commit a61a4a1db0 with DM_MMC,
exynos boards now enumarates external SD/MMC slot as mmc2, instead of mmc1
with legacy mode. Moving mmc2 before mmc1/0 restore the previous behavior
of trying external SD/MMC before internal slot.
Signed-off-by: Guillaume GARDET <guillaume.gardet@arm.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The mmc_spi driver's priv is not available in its bind phase(). Use
platdata instead.
Fixes: 05e35d4297 ("mmc: mmc_spi: Re-write driver using DM framework")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are two cases not been considered:
- use uint for timeout, it will overflow when size bigger than 512KB for
it *8*1000 at the beginning, but we may use size up to 32MB; The
'timeout' will overflow if size bigger than 51.2MB after this fix, which
should be enough for U-Boot;
- The timeout is using clock speed for data rate, but the device may not
have such high speed, eg. clock is 52MHz while the device write speed may
be less than 10MB/s, and we may use up to 150MHz clock.
Fix them in this patch, the max timeout is about 6500 when size is 32MB
after fix.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Enable the MMC subsystem and the Aspeed SD controller. Also enable the
use of the device tree for probing the controller.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.
While at it, add time units info as comments to struct mmc fields.
This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
mmc_wait_dat0() expects timeout argument to be in usec units. But some
overlying functions operate on timeout in msec units. Convert timeout
from msec to usec when passing it to mmc_wait_dat0().
This fixes 'avb' commands on BeagleBoard X15, because next chain was
failing:
get_partition() -> mmc_switch_part() -> __mmc_switch() ->
mmc_wait_dat0()
when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0().
Fixes: bb98b8c5c0 ("mmc: During a switch, poll on dat0 if available and check the final status")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
When look through the code, I found this bare metal
drives is not used, so remove it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With GCC 9.2.1 net/nfs.c leads to multiple errors of type
address-of-packed-member.
net/nfs.c: In function ‘rpc_req’:
net/nfs.c:199:18: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
199 | p = (uint32_t *)&(rpc_pkt.u.call.data);
| ^~~~~~~~~~~~~~~~~~~~~~
net/nfs.c: In function ‘nfs_readlink_reply’:
net/nfs.c:631:46: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
631 | nfs3_get_attributes_offset(rpc_pkt.u.reply.data);
| ~~~~~~~~~~~~~~~^~~~~
LD drivers/block/built-in.o
net/nfs.c: In function ‘nfs_read_reply’:
net/nfs.c:692:46: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
692 | nfs3_get_attributes_offset(rpc_pkt.u.reply.data);
| ~~~~~~~~~~~~~~~^~~~~
struct rpc_t is only used as local variable. It is naturally packed. So
there is no need for the attribute packed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
rpc_pkt.u.call.data is an array of uint32_t. There is no need to convert
it to uint32_t *.
memcpy() expects void * as it 1st and 2nd argument. There is no point in
converting pointers to char * before passing them to memcpy().
In ntohl(data[1]) != 0 calling ntohl() is superfluous. If the value is
zero, does not depend on the byte order.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some environment variables are relevant for networking. For these
U_BOOT_ENV_CALLBACKs have been defined. When the corresponding environment
variable is updated the callback updates the state of the network
sub-system.
In the UEFI subsystem we can use the network even if CONFIG_CMD_NET is not
defined.
Let the usage of the U_BOOT_ENV_CALLBACKs depend on CONFIG_NET and not on
CONFIG_CMD_NET.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a check to rpc_pkt.u.reply.data at nfs_lookup_reply.
Signed-off-by: Cheng Liu <liucheng32@huawei.com>
Reported-by: Fermín Serna <fermin@semmle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a check to rpc_pkt.u.reply.data at nfs_readlink_reply.
Signed-off-by: Cheng Liu <liucheng32@huawei.com>
Reported-by: Fermín Serna <fermin@semmle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a check to rpc_pkt.u.reply.data at nfs_read_reply.
Signed-off-by: Cheng Liu <liucheng32@huawei.com>
Reported-by: Fermín Serna <fermin@semmle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a check to nfs_handler to fix buffer overflow for CVE-2019-14197,
CVE-2019-14200, CVE-2019-14201, CVE-2019-14202, CVE-2019-14203 and CVE-2019-14204.
Signed-off-by: Cheng Liu <liucheng32@huawei.com>
Reported-by: Fermín Serna <fermin@semmle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a check to udp_len to fix unbounded memcpy for
CVE-2019-14192, CVE-2019-14193 and CVE-2019-14199.
Signed-off-by: Cheng Liu <liucheng32@huawei.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reported-by: Fermín Serna <fermin@semmle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The net_random_ethaddr() tries to get some entropy from different
startup times of a board. The seed is initialized with get_timer() which
has only a granularity of milliseconds. We can do better if we use
get_ticks() which returns the raw timer ticks. Using this we have a
higher chance of getting different values at startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
