The bios emulator in the MAI board can not pass compile
and have a lot of crap in it. remove it and will have a
clean and small bios emulator in the drivers directory
which can be uesed for every board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
This patch add definition of the BIOS emulator and the ATI framebuffer
driver for MPC8641HPCN board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Additionally export the following fuctions (to make trab_config build again):
- simple_strtol()
- strcmp()
Also bump the ABI version to reflect this change
Signed-off-by: Martin Krause <martin.krause@tqs.de>
All of the PCI/PCI-Express driver and initialization code that
was in the MPC8641HPCN port has now been moved into the common
drivers/fsl_pci_init.c. In a subsequent patch, this will be
utilized by the 85xx ports as well.
Common PCI-E IMMAP register blocks for FSL 85xx/86xx are added.
Also enable the second PCI-Express controller on 8641
by getting its BATS and CFG_ setup right.
Fixed a u16 vendor compiler warning in AHCI driver too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
During config transactions on the PCIe bus an attempt to scan for a
non-existent device can lead to a machine check exception with certain
peripheral devices. In order to avoid crashing in such scenarios the
instrumented versions of the config cycle read routines are introduced, so
the exceptions fixups framework can gracefully recover.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
This brings back separate settings for PCIe bus numbers depending on chip
revision, which got eliminated in 2b393b0f0a
commit. 440SPe rev. A does NOT work properly with the same settings as for
the rev. B (no devices are seen on the bus during enumeration).
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)
Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)
Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map
Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Clear ECC status regs after ECC POST test
- Set dcbz for ECC generation with caches enabled as default
- Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Change Lime SDRAM initialization to now support 100MHz and
133MHz (if enabled). Also the framebuffer is initialized to
display a blue rectangle with a white border.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
As spotted by Matthias Fuchs, the default output values for all GPIO1
outputs were not setup correctly. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds ECC Post test for the Lwmon5 board based
on PPC440EPx to U-Boot.
Signed-off-by: Pavel Kolesnikov <concord@emcraft.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch fixes the negative consequences for 8xx of the recent
"ppc4xx: Clean up 440 exceptions handling" commit.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.
Signed-off-by: Stefan Roese <sr@denx.de>
The new "weak" functions ddr_wrdtr() and ddr_clktr() are added to better
support non default, boardspecific DDR(2) controller configuration.
Signed-off-by: Stefan Roese <sr@denx.de>
The new function remove_tlb() can be used to remove the TLB's used to
map a specific memory region. This is especially useful for the DDR(2)
setup routines which configure the SDRAM area temporarily as a cached
area (for speedup on auto-calibration and ECC generation) and later
need this area uncached for normal usage.
Signed-off-by: Stefan Roese <sr@denx.de>
