If the source .env file changes to one that is also older than the
generated env.txt file then the .env file is not regenerated. This
means when switching board configs we do not regenerate the env.
This can be tested with:
$ make j721e_evm_a72_defconfig
$ make # this may fail to complete but that is okay for this test
$ make am64x_evm_a53_defconfig
$ make
$ vim include/generated/env.txt
Note this is still the J721e env not the AM64 config as expected.
As ENV_FILE is set based on configuration, regenerate anytime
autoconf.h changes.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all
to required pinctrl nodes to simplify use of the prevent booting on
power plug-in option in SPL.
With the following Kconfig options and nodes in u-boot.dtsi the prevent
booting on power plug-in option can work in SPL.
CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PMIC_RK8XX=y
&i2c0 {
bootph-pre-ram;
};
&rk817 {
bootph-pre-ram;
regulators {
bootph-pre-ram;
};
};
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 30975fb73d ("rockchip: Add option to prevent booting on
power plug-in") introduce an option to prevent booting a device when the
device was powered on due to power plug-in instead of pressing a power
button.
This feature works by checking the power-on source during PMIC probe
and powers off the device if power-on source was power plug-in.
This check currently runs very late at PMIC probe in U-Boot proper.
Fix so that the power-on source check can work at probe time in SPL.
Also enable probe after bind and remove the PMIC banner in SPL.
With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and
SPL_PMIC_RK8XX to power off the device very quickly after TPL instead
of after TF-A and U-Boot proper has been loaded and run.
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
change to: 324MHz
clk skew:0x64
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
clk skew:0x40
out
Power Off due to plug-in event
Fixes: 30975fb73d ("rockchip: Add option to prevent booting on power plug-in")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With PMIC_RK8XX, SYSRESET and CMD_POWEROFF options enabled it is
possible to power down a board using the poweroff command and turn the
board back on using a power button.
Enable the poweroff command on RK356x boards that have a button wired
to PMIC pwron.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the
poweroff command when PMIC_RK8XX is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Without DOS_PARTITION support U-Boot is not able to boot an OS stored
into an SD card with MBR partitions table. This is still a quite common
case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip
RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are
the only RK boards missing of DOS_PARTITION.
Reported-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK3588 boards that
have an enabled gmac node and drop ETH_DESIGNWARE and GMAC_ROCKCHIP for
remaining RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK356x boards that
have an enabled gmac node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove spam of RX packet not available debug messages when waiting to
receive a packet.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Return error code when phy_connect fails or no link can be established.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rx_pkt is allocated and not used for anything, remove it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for generating a LZMA-compressed U-boot binary with the
help of binman, if CONFIG_SPL_LZMA is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for generating a GZIP-compressed U-boot binary with the
help of binman, if CONFIG_SPL_GZIP is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update and improve documentation about build steps for SoCs that
require using TF-A and TPL binaries provided by Rockchip, such as
rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in
the list of supported boards. Minor page format improvements.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on rk3308 SoC using U-Boot
TPL or SPL, and therefore an external TPL binary must be used to
package a bootable u-boot-rockchip.bin image.
Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308.
Remove useless TPL_SERIAL.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the Rockchip IO-domain driver for RK3568 from linux.
The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.
It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.
Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Information from the first range group is always used to calculate the
voltage returned for buck converters. This may result in wrong voltage
reported back to the regulator_get_value caller.
Traverse all the possible BUCK ranges to fix this issue.
Fixes: addd062bea ("power: pmic: rk816: support rk816 pmic")
Fixes: b62280745e ("power: pmic: rk805: support rk805 pmic")
Fixes: b4a35574b3 ("power: pmic: rk817: support rk817 pmic")
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, simplify buck get_value, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Route signal from comb PHY instead of PCIe3 PHY to PCIe1l0 and PCIe1l1.
Fixes use of pcie2x1l0 on ROCK 5B.
Code imported from mainline linux driver.
Fixes: c5b4a012bc ("phy: rockchip: naneng-combphy: Support rk3588")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3588 variant to the driver.
Code imported almost 1:1 from mainline linux driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure aggregation or bifurcation mode on RK3568 based on the value
of data-lanes property.
Code imported almost 1:1 from mainline linux driver.
Fixes: 6ec62b6ca6 ("phy: rockchip: Add Rockchip Synopsys PCIe 3.0 PHY")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a phy_init ops in preparation for upcoming support of a RK3588
variant in the driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use clk_bulk API and syscon_regmap_lookup_by_phandle to
simplify in preparation for upcoming support of a RK3588 variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set number of lanes and link width speed control register based on the
num-lanes property.
Code imported almost 1:1 from dw_pcie_setup in mainline linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To quote the author:
This series tidies up SPL a little and adds some core ofnode functions
needed to support Universal Payload. It also includes a few minor
fix-ups for sandbox.
For SPL the changes include CONFIG naming, removing various #ifdefs and
tidying up the FIT code.
One notable piece of the ofnode improvements is support for flattening a
livetree. This should be useful in future as we move FDT fixups to use
the ofnode API.
The PCI helpers read only the base address for a PCI region. In some cases
the size is needed as well, e.g. to pass along to a driver which needs to
know the size of its register area.
Update the functions to allow the size to be returned. For serial, record
the information and provided it with the serial_info() call.
A limitation still exists in that the size is not available when OF_LIVE
is enabled, so take account of that in the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function cannot return true if PCI is not enabled, since no PCI
devices will have been bound. Add a check for this to reduce code size
where it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The spl_phase() function indicates whether U-Boot is in SPL and before
or after relocation. But sometimes it is useful to check for SPL with
zero code-size impact. Since spl_phase() checks the global_data flags,
it does add a few bytes.
Add a new spl_in_proper() function to check if U-Boot proper is
running, regardless of the relocation status.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses ARRAY_SIZE() but does not include the header file which declares
it. Fix this, so that command.h can be included without common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Typically the bloblist is set up after the devicetree is present. This
makes sense because bloblist may use malloc() to allocate the space it
needs.
However sometimes the devicetree itself may be present in the bloblist.
In that case it is at a known location in memory so we can init the
bloblist very early, before devicetree.
Add a flag to indicate whether the bloblist has been inited. Add a
function to init it only if needed. Use that in the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this down by 4KB so that it is large enough to hold the devicetree.
Also fix up the devicetree address in the documetation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not read this unless requested. Make it conditional on the
option being provided.
Add some debugging to show the state being written.
Signed-off-by: Simon Glass <sjg@chromium.org>
