This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Unfortunately this driver uses the old video structure to store things.
This is not supported with driver model.
Drop the old code and comment out the other pieces, so the maintainer can
take a look.
Signed-off-by: Simon Glass <sjg@chromium.org>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry)
Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND)
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The code was mistakenly initializing the input buffer twice.
Tested to be working on BeagleBone by adjusting CONFIG_SYS_BOOTM_LEN to
64MiB (probably works with less) and preparing uImage with:
cat arch/arm/boot/Image \
| zstd --ultra -22 --zstd=windowLog=22 \
> linux.bin.zst
mkimage -A arm -T kernel uImage -C zstd -d linux.bin.zst \
-a 0x80008000 -e 0x80008000
Without the windowLog restriction, bootm fails with a zstd decompression
error 7 (window too large), which I haven't troubleshooted.
There should be a bit more documentation on the feature...
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes: 458b30af66 image: Update image_decomp() to avoid ifdefs
make sandbox_defconfig
make mrproper
make tests
fails with
../drivers/video/u_boot_logo.S: Assembler messages:
../drivers/video/u_boot_logo.S:5: Error: file not found: drivers/video/u_boot_logo.bmp
We have to delete the generated file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current approach for setting the environment variables that
describe the memory layout runs the risk of overlapping with
reserved memory regions. Use the lmb code to derive the addresses
for these variables instead.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The firmware on larger NVMe drives needs more than 100ms to come up.
Change the timeout to 1s.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* man-page for the wdt command
UEFI:
* Unit test for boot manager
-----BEGIN PGP SIGNATURE-----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=n5MM
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc5-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5-2
Documentation:
* man-page for the wdt command
UEFI:
* Unit test for boot manager
When calling efi_dp_from_name() we are not interested in the device part.
Just pass NULL as an argument.
Suggested-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a unit test for
* efidebug boot add
* efidebug boot order
* bootefi bootmgr
* initrd via EFI_LOAD_FILE2_PROTOCOL
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Up to now the initrddump.efi application has drained the input after
showing the prompt. This works for humans but leads to problems when
automating testing. If the input is drained, this should be done before
showing the prompt.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
initrddump.efi uses colored output and clear the screen. This is not
helpful for integration into Python tests. Allow specifying 'nocolor' in
the load option data to suppress color output and clearing the screen.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Use the MEMA - MEMD registers on the PFUZE100 as bootcount
registers.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add missing MEMA - MEMD register definitions for PFUZE100.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add the PWM node and enable it for AST2600 EVB
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patch add the support of PWM controller which can be found at aspeed
ast2600 soc. The pwm supoorts up to 16 channels and it's part function
of multi-function device "pwm-tach controller".
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Macros PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* are unused and are
duplication of PCI_CLASS_* macros defined in pci_ids.h header file.
So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace old macros PCI_CLASS_CODE_COMM and PCI_CLASS_SUB_CODE_COMM_SERIAL
by new macros defined in pci_ids.h. Old macros would be deleted in followup
commit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds support for using -Og when building U-Boot. According to the
gcc man page:
> -Og should be the optimization level of choice for the standard
> edit-compile-debug cycle, offering a reasonable level of optimization
> while maintaining fast compilation and a good debugging experience.
This optimization level is roughly -O1 minus a few additional
optimizations. It provides a noticably better debugging experience, with
many fewer variables <optimized out>.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a separate CONFIG_CC_OPTIMIZE_FOR_SPEED option in a choice,
in preparation for adding another optimization option. Also convert SH's
makefile to use this new option.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For consistency in runs, we need to always use the same pylint version.
Pin to 2.12.2 as this is what we have been using so far.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>