Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface. The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Calxeda highbank SOC needs a custom sequence to bring up SATA links,
so override ahci_link_up with custom function to handle combophy setup.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Richard Gibbs
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
To support the Armada 38x, new values for the request-delay and the
response-timeout are needed. As the values already implemented in
this tool (for Kirkwood and Armada XP) don't seem to work here.
To make this more flexible, lets add make those 2 parameters
configurable via the cmdline. Here the new parameters:
-q <req-delay>: use specific request-delay
-s <resp-timeo>: use specific response-timeout
For the Marvell DB-88F6820 these values are known to work:
One board:
-q 2 -s 1
2nd board:
-q 5 -s 5
So this seems to be even board specific. But with this patch now
those values can be specified and tested via the cmdline.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Luka Perkov <luka.perkov@sartura.hr>
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
L2 cache may still be enabled by the BootROM. We need to first disable
it before enabling d-cache support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
If defined, the macro CONFIG_SYS_SPI_U_BOOT_OFFS allows a board
to specify the offset of the payload image into the kwb image
file. This value was being used to locate the image, but was not
used in the "header size" field of the main header. Move the
use of this macro into the function that returns the header size
so that the same value is used in all places.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Stefan Roese <sr@denx.de>
The AHCI driver currently waits 5s before timing out when sending a
data command to a drive. Some drives take upwards of 8s to respond to
the initial data command while they're spinning up. Increase the
data io timeout to 10s so that those drives can be found on initial
scsi scan.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Calxeda Midway part has A15 cores, which do not have the Highbank
A9's SCU used there for resetting the chip.
Add code to distinguish between the A9 and the A15 and invoke the
appropriate register writes to support the newer part.
Andre: rework detection of Highbank vs. Midway
Rob: fix Andre's reworked detection
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Now all manual mode configurations are done as part of
IO delay recalibration sequence, remove the hack done for
CPSW.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A generic is_dra72x cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating EMIF registers to enable HW leveling
on DRA72-evm.
Also updating the timing registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit imports some updates of kconfiglib.py from
https://github.com/ulfalizer/Kconfiglib
- Warn about and ignore the "allnoconfig_y" Kconfig option
- Statements in choices inherit menu/if deps
- Add Symbol.is_allnoconfig_y()
- Hint that modules are still supported despite warnings.
- Add warning related to get_defconfig_filename().
- Fix typo in docs.
- Allow digits in $-references to symbols.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Philip Craig <philipjcraig@gmail.com>
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit e11c6c279d broke calculating lr register
in function save_boot_params() and caused U-Boot to crash at early boot time
on Nokia N900 board.
This patch fix calculating return address in lr register and make Nokia N900
board bootable again. Patch was tested in qemu and also on real N900 HW.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
