This is useful for display parameters. Add a simple decode function to read
from this device tree node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sort uclasses into alphabetical order and tidy up the comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Having this as a Kconfig allows it to be a dependent feature.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As this board seems to be unmaintained for quite some time, and its
not moved to the generic board ingrastructure, lets remove it.
This will also enable us to remove the CONFIG_AUTOBOOT_DELAY_STR2
and CONFIG_AUTOBOOT_STOP_STR2 macros, as this sc3 board is the
only one using one of this macros. A removal patch will follow
soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Juergen Beisert <jbeisert@eurodsn.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch adds device tree for the ST Micro stv0991 board & enables
device tree control. Progressively device tree support for the drivers
being used will also be added.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If regular NAND booting fails to find a valid uImage in the
kernel partition in NAND, try to boot using a zImage and dtb found
in a UBI volume in the rootfs partition. This is the NAND analog
of mmc zImage booting for device-tree based kernels.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Overo COMs have NAND flash that requires 4-bit ECC or better except for
the first sector which can use 1-bit ECC. The boot ROM expects to load
a payload from NAND written using 1-bit hardware-based ECC. In short,
write SPL to NAND something like this (4 times for redundancy):
#> nandecc hw
#> nand write ${loadaddr} 0x0 ${filesize}
#> nand write ${loadaddr} 0x20000 ${filesize}
#> nand write ${loadaddr} 0x40000 ${filesize}
#> nand write ${loadaddr} 0x60000 ${filesize}
Then, switch back to software-based BCH8 for everything else:
#> nandecc sw bch8
After [1], enlarge the max size of the SPL so the BCH code can fit.
[1] https://www.mail-archive.com/u-boot@lists.denx.de/msg163912.html
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Add the stm32F4 board's serial ports support.
User can use it easily.
The user only need to edit the number of the usart.
The patch also fix the serial print out.
Last, this version of patch fix the first patch checkpatch.pl error.
Thanks to Kamil Lulko.
Signed-off-by: kunhuahuang <huangkunhua@gmail.com>
usbupdate in real does allways load some script from usb-storage and execute
it, on all B&R targets.
So we do following 2 things:
- rename it to what it really does
- move it from boards to common environment
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Since we display in future the splash screen out of linux-os, we don't need
this support anymore within the common section.
But kwb-target is still using BMP_DISPLAY feature, so we move the related
from the common section into the target-specific.
Also the default environment of tseries will be adapted to this.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Since the used AM3352 SoC doesn't have GPU it isn't allways necessary to build
in complete drm-stuff into linux kernel. In very small applications only we use
the simple-framebuffer.
So we have 2 use-cases:
- device operating on drm-driver (let simplefb node disabled)
- device operating on simplefb-driver (activate simplefb node and reserve mem)
The decision is made by means of "simplefb" environment variable.
simplefb = 0
we don't enable the (maybe) existing simplefb node and all the rest around
display is up to the linux-kernel. We just disable the backlight, beceause we
do not want see the flicker during take over of drm-driver.
simplefb = 1
we enable the (maybe) existing simplefb node and reserve framebuffers size
in memory.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
the CONFIG_LCD_NOSTDOUT feature never had become mainline in uboot due to the
fact that the problem of "not writing out whole console to lcd" can be solved
with another way.
So we remove this unnary define.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
We take use of the new LCD_ROTATION feature.
The information about how the display is rotated is taken from B&R specific
(/factory-settings/rotation) information in the devicetree.
The information there is stored as string (cw, ud, ccw, none) since starting
support of this devices and cannot be changed, so we have to convert it into
none = 0
cw = 1
ud = 2
ccw = 3
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This patch fixes cross-compiling U-Boot tools with the musl C library:
* including <sys/types.h> is needed for ulong
* defining _GNU_SOURCE is needed for loff_t
Tested for target at91sam9261ek_dataflash_cs3.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Tom Rini <trini@konsulko.com>
Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures the environment
variables are reused and insures devices across product lines share the same
values.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For the distro_bootcmds to succeed on the sandbox a bit of setup is
required (e.g. network configured or host image bound), so running them
by default isn't that useful.
Add a -b/--boot command to the sandbox binary, which triggers the
distro_bootcmds to run after the other command-line commands.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make usb_get_bus easier to use for callers, by directly returning the bus
rather then returning it via a pass-by-ref argument.
This also removes the error checking from the current callers, as
we already have an assert() for bus not being NULL in usb_get_bus().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a uclass for real-time clocks which support getting the current time,
setting it and resetting the chip to a known-working state. Some RTCs have
additional registers which can be used to store settings, so also provide
an interface to these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the definition of struct rtc_time into a separate file so that sandbox
can include it without requiring common.h and the like.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need to use u8, and if we avoid it, it isn't so much of a problem
that rtc.h includes this header. With this change we can include rtc.h from
sandbox files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most callers unpack the structure and pass each member. It seems better to
pass the whole structure instead, as with the C library. Also add an rtc_
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Rename this function so that it is clear that it is provided by the RTC.
Also return an error when it cannot function as expected. This is unlikely
to occur since it works for dates since 1752 and many RTCs do not support
such old dates. Still it is better to be accurate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Change this function name to something more descriptive. Also return a
failure code if it cannot calculate a correct value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
At present this driver has a few test features. They are needed for running
the driver model unit tests but are confusing and unnecessary if using
sandbox at the command line. Add a flag to enable the test mode, and don't
enable it by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model versions of the legacy functions to read and write a
single byte register. These are a useful shortcut in many cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This comment should refer to SPI, not serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Only set the speed if it has changed from last time. Since the speed will
be 0 when the device is probed it will always be changed on the first
transfer after the device is probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:
tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This enables the usage of the "preboot" environment variable on Marvell
boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.
Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.
[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.
Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
