Commit graph

143 commits

Author SHA1 Message Date
Eric Nelson
cfb8b9d335 i.MX6: consolidate pad names for multi-CPU boards
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board
may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo
(MX6DL) by including the proper header.

Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd
only support MX6Q, so they include mx6q_pins.h.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-03-07 16:43:46 +01:00
Fabio Estevam
76c91e668a mx6: Disable Power Down Bit of watchdog
On a mx6qsabresd revision C board with rev1.2 mx6q, the system gets resetted
and it is not able to reach the Linux prompt.

Comparing the watchdog behaviour on a revB versus revC board:

- On a mx6qsabresd revB:

U-Boot > reset
resetting ...

U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)

CPU:   Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: WDOG
...

- On a mx6qsabresd revC:

U-Boot > reset
resetting ...

U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)

CPU:   Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR

So due to revC POR/watchdog circuitry whenever a watchdog occurs, it causes a POR.

Clearing the PDE - Power Down Enable bit of WMCR registers fixes the problem and
is also safe for all mx6 boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-02-12 13:54:34 +01:00
Troy Kisky
34275d70fe arch-mx6: add mx6dl_pins.h
Only the values used in the sabrelite board are
added currently. Add more as other boards use them.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10 08:15:40 +01:00
Troy Kisky
eb0344d974 imx-common: cpu: add imx_ddr_size
Read memory setup registers to determine size
of available ram. This routine works for mx53/mx6x

I need this because when mx6solo called get_ram_size
with a too large maximum size, the system hanged.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10 08:15:40 +01:00
Troy Kisky
20332a066a mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololite
Previously, the same value was returned for both mx6dl and mx6solo.
Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev
stored at 0x280 instead of 0x260.
I don't have a sololite to verify.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10 08:15:40 +01:00
Eric Nelson
f95c960bcc i.MX6: add HDMI transmitter register declarations from kernel WIP.
Original source from Pengutronix HDMI driver work:

	http://git.pengutronix.de/?p=imx/linux-2.6.git;a=commitdiff;h=72c31cd67ac880bd90785af86f8e46f8ea7b3bb0

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16 12:35:11 +02:00
Eric Nelson
0fb1e57cb6 i.MX6: set drive strength for parallel RGB pads
Default drive strength is disabled and won't function.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16 12:35:11 +02:00
Fabio Estevam
dce67bd548 mx6qsabreauto: Pass the board revision to the kernel
The kernel from Freescale expects that the bootloader passes the board revision.

Read the board revision and pass it via get_board_rev().

Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16 12:35:11 +02:00
Benoît Thébaudeau
833b6435de mx5/6: Define default SoC input clock frequencies
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:10 -07:00
Matthias Weisser
e7bed5c2b3 imx: Use MXC_I2C_CLK in imx i2c driver
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Eric Nelson
2af7e81015 i.MX6: get rid of redundant struct src_regs (dupe of struct src)
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:09 -07:00
Eric Nelson
de710a14b5 i.MX6: define struct iomuxc and IOMUX_GPR2 register bitfields
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:09 -07:00
Eric Nelson
e66ad6e747 i.MX6: Add ANATOP_PFD_480 bitfield constants
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:09 -07:00
Eric Nelson
a83e1b7b8c i.MX6: define IOMUX_GPR3 register bitfields
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:09 -07:00
Eric Nelson
344da71a20 i.MX6: define bitfields for CHSCCDR register
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:09 -07:00
Eric Nelson
da6df2d1c8 i.MX6: change register name for CCM_CHSCCDR to match ref. manual
Register CCM_CHSCCDR (offset 0x34 in CCM) is named CCM_CHSCCDR in
reference manual, but was named chscdr in struct mxc_ccm_reg.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:08 -07:00
Eric Nelson
0bb7e316f0 i.MX6: provide functional names for CCM_CCGR0-CCGR6 bit fields
Add meaningful constants for each clock channels and use them for
enabling and disabling i.MX6 clocks.

Includes an update to enable/disable the IPU1 clock in
drivers/video/ipu_common to remove IMX5x register access
when used on i.MX6 as discussed in V1:

     http://patchwork.ozlabs.org/patch/185129/

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:08 -07:00
Stefano Babic
19f59ea6db MX6: drop binary constants from iomux header
Constants set with binary value (0b...) are not compiled
from old toolchain when used by the clrsetbits_le32 macro.
Replaces them with the corresponding hex value.

The error reported (for example with the mx6qsabrelite board)
is something like:

mx6qsabrelite.c:369:1: error: invalid suffix "b101" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b10010" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b0000" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b10001" on integer constant

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-17 13:17:06 +02:00
Benoît Thébaudeau
8e99ecd74b mxc: Define architecture identifier
Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.

The i.MX28 is omitted because its architecture is a bit different (like imx/mxc
vs. mxs in Linux).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
2012-09-01 14:58:30 +02:00
Stefano Babic
5fecb36ca0 MX: Set a common gpio.h for all i.MX
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
2012-09-01 14:58:27 +02:00
Troy Kisky
124a06d7fb imx-common/cmd_bmode.c: add imx bmode (bootmode) command
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.

Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:26 +02:00
Troy Kisky
d1c679a46d iomux: move IOMUX_GPR13_xxx defines
Move mx6 specific defines to arch-mx6 directory.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:26 +02:00
Troy Kisky
cc54a0f7cc imx-common: add i2c.c for bus recovery support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:57 +02:00
Troy Kisky
af2a35fb1f i.mx: iomux-v3.h: move to imx-common include directory
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:19 +02:00
Ashok
6b8ac524e7 mx6: Make pad name macro consistent with the datasheet
Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-20 23:03:28 +02:00
Fabio Estevam
05d4df1d8a mx6: Allow mx6 to access the IPUv3 registers
Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-10 11:35:38 +02:00
Jason Liu
0d952e5d2e i.mx: i.mx6x: NO_MUX_I/NO_PAD_I not set correctly
If one PAD does not have mux or pad config register, we need
set the NO_MUX_I/NO_PAD_I to 0, the old value is not correct

Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-07 14:07:25 +02:00
Eric Nelson
64e7cdb5e8 i.MX6: add enable_sata_clock()
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:33 +02:00
Dirk Behme
cac833a98c i.MX6: Add ANATOP regulator init
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.

Note: This should be but can't be done in the DCD. The bootloader
      prevents access to the ANATOP registers.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
2012-05-15 08:31:33 +02:00
Fabio Estevam
6a376046ef imx-common: Factor out get_ahb_clk()
get_ahb_clk() is a common function between mx5 and mx6.

Place it into imx-common directory.

Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:32 +02:00
Vikram Narayanan
a9407f2bc5 imx: Remove unneeded/repititive definitions from imx headers
Remove gpio related unused/repititive definitions from imx headers.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Eric Nelson
c415919d57 i.MX6: define CACHELINE_SIZE
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-04-16 14:53:58 +02:00
Fabio Estevam
a768386746 mx6: Read silicon revision from register
Instead of hardcoding the mx6 silicon revision, read it in run-time.

Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.

Tested on a mx6qsabrelite, where it shows:

CPU:   Freescale i.MX6Q rev1.0 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27 09:41:16 +02:00
Fabio Estevam
334bd0e225 mx6: Remove duplicate definition of ANATOP_BASE_ADDR
Remove duplicate definition of ANATOP_BASE_ADDR.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:16 +02:00
Wolfgang Grandegger
3f467529ca usb/ehci: Add USB support for the MX6Q
Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-26 23:09:23 +02:00
Troy Kisky
28774cbaac net: fec_mxc: add 1000 Mbps selection
Define FEC_QUIRK_ENET_MAC and add to
arch-mx6/imx-regs.h

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27 21:19:24 +01:00
Eric Nelson
d5c37c9cc4 mx6q: Add support for ECSPI through mxc_spi driver
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-27 21:19:23 +01:00
Eric Nelson
4b3a30e9ae mx6q: define GPIO macros for translating between ordinals and port:index
The interface to the mxc_gpio driver uses integer (ordinal) values to
refer to all GPIOs on the i.MX processors. The registers themselves
and much of the i.MX documentation are banked in groups of 32, and these
macros allow the use of the port:index numbering for clarity.

GPIO_NUMBER() converts to ordinal value from port:index
GPIO_PORT() returns the port of an ordinal value
GPIO_INDEX() returns the index or offset of the ordinal.

Discussion on the mailing list at
	http://lists.denx.de/pipermail/u-boot/2012-January/116927.html

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-02-27 21:19:23 +01:00
Troy Kisky
4591f523df i.mx6: mx6x_pins: Fix uart txd definitions
The uart txd pad can also provide the rxd function. But it does not stop its
tx role. This could be used for a half duplex serial port.

Change names to reduce confusion.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12 10:11:26 +01:00
Jason Liu
f2f7745825 imx: mx6q: add aipstz init for off platform periph
Init peripheral access control register of AIPSTZ OPACRx:

Buffer Writes(BW):      0 -> not bufferable,
Supervisor Protect(SP): 0 -> not require supervisor privilege level for accesses.
Write Protect(WP):      0 -> allows write accesses.
Trusted Protect(TP):    0 -> allows unstrusted master

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:10 +01:00
Jason Liu
bd2e27c043 i.mx6:imx6q: allign MAC address with burned-in ordering
For the i.mx6q, the burned-in MAC address will be the following odering,

fuse: 0x620[7:0]   MAC_ADDR[7:0]     ---> mac[5]
fuse: 0x620[15:8]  MAC_ADDR[15:8]    ---> mac[4]
fuse: 0x620[23:16] MAC_ADDR[23:16]   ---> mac[3]
fuse: 0x620[31:24] MAC_ADDR[31:24]   ---> mac[2]
fuse: 0x630[7:0]   MAC_ADDR[39:32]   ---> mac[1]
fuse: 0x630[15:8]  MAC_ADDR[47:40]   ---> mac[0]

This patch also fix the error caculation for the fuse bank[0] address

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Fabio Estevam
be252b654a net: imx: Add multi-FEC support for imx_get_mac_from_fuse
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.

This feature is important on mx28 SoC for example that has two FEC ports.

Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Jason Liu
23608e23fd i.mx: add the initial support for freescale i.MX6Q processor
i.MX6Q is freescale quad core processors with ARM cortex_a9 complex.
This patch is to add the initial support for this processor.

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de>
2011-12-09 17:30:10 +01:00